• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

83 Scrambler Restoration Project-Georgia

Need some help from the group....does anyone know a good shorty header option for an AMC 304....the Headman Headers I bought don't fit....and if I cannot find a good Shorty Header then I will just have to use a manifold instead. thanks in advance...
 
Man I LOVE that color.... I think I want one like that instad of black or even red now.

Keep it up and post more picks.

;)
 
Latest Update of Pictures

We are getting there....taking awhile longer than hoped as we had to fabricate a few parts....hoping to get it back to body shop tomorrow to finish putting back on parts....we shall see....had hoped to be finished by now. Oh well...I think it will be worth the wait...:cheers:
 
Last edited:
Headed back to body shop for final detail work

Still things to do on the engine, transmission, exhaust, etc....but it is headed back to body shop for final body work. Engine runs great but having a problem with Oil pressure....which we think we can fix with a HP Oil Filter....as I put a cheapo on it. Sounds great....still need to do final checks before it is ready for the road in a few weeks. CH

attachment.php
 
Still working on it...

It is getting closer....been working on it and slowly putting it back together. It is funny how things fit differently when you put them back together.....seems like we have to keep making modifications. I thought I would have been done by now. I just hope I have it ready to roll before it gets to cold to drive without the top. Will post more pictures when I have time...:wave:


attachment.php
 
That is a slick looking Jeep. that is the same color as my Tacoma. Love it.
 
Need some help/input

Got it cleaned up yesterday and then we fired it up to move it back inside the shop. When we did the Oil Filter gasket blew (for the 2nd time) and I shut it down. These pictures were taken before that...

I have exhaust manifolds on and I am thinking the heat might have caused some of the problems. I am having it hauled to the muffler shop next week to have the muffler fabricated....so I am not going to start the engine again until we get the muffler installed.

I would appreciate any help with other explanations as to why I might have this issue??? I am going to install a High Pressure K&N filter that has 550 PSI pressure rating to see if that solves the problem as well. All input is welcome...thanks, CH

attachment.php


attachment.php
 
Last edited:
It sounds like something may be restricting oil from circulating through the block.
 
It sounds like something may be restricting oil from circulating through the block.


Thanks....where would I start as far as eliminating things? How can you check if Oil is circulating through the block without tearing the engine apart? This is frustrating....:banghead:
 
I blew an oil filter at the gasket once. When I took the new filter off, the old gasket from the previous filter was stuck to the block. Make sure there isn't an old gasket stuck on there.
 
Had an old Chevy that did the same thing. Turned out to be the pressure relief in the oil pump. Swaped the pump out and all was good. Don't know if AMC works the same way.
 
Leaving the Body shop...

Paint & body all done....I have a few minor places that we will fix when I go back for final detail...but very happy with how it turned out. Also...big Kudo's :woot: to the gang at Bulltear for talking me through my high oil pressure issue. I have a relocation kit that I have coming that I think will fix the problem. When we replaced the old engine with the new crate V8 304...I did not keep the original screw in oil filter adapter....and the ones they make now are 1/16 inch smaller....which is why my oil filter kept blowing off. It will actually work much better as I am going to relocate the filter to the frame which will make for much easier oil changes in the future. Also, I am going to loom all the new painless wiring this weekend to clean up the wire around the engine. Will send pictures of that when I get done...

Monday I am having it picked up from the house to deliver to the Muffler shop to have the muffler fabricated. After I get it back...I am going to re-run the brakes lines and then I think I am ready for my first test drive....cannot wait!!!! :cheers:

Thanks to all on this board for the help in the Oil pressure problem....here are pictures as of this afternoon....the last one it is loaded up headed back to my house! Best, CH

attachment.php


attachment.php


attachment.php


attachment.php


attachment.php
 
Last edited:
Half door options

It looks like the best fit is modifying TJ uppers. There are some write ups on here and others places on the internet.

I am using a set of hard fiberglass sliders for a yj that I found after seeing them in a picture that fit. Not sure of the brand, but they fit pretty good. Not a perfect seal, but with a little work I think I can make a good seal. I like the look of the half doors with the yj mirrors.
 
I dont have any suggestions. I am in need of a pair for my scrambler before winter hits. I was planning on the TJ uppers but I was hoping to talk to someone that has done it before I buy a pair. Nice Scrambler it looks great!!
 
When a Jeep looks this good after a build it inspires me to keep going. You did a great job and did not go overboard like some Jeep builds I have seen over the years.
 
Back
Top