• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

'93 4.0L Swap into '84 Scrambler

I used Fuel Injection rated fuel line @ like $9.00 per foot plus fuel injection rated hose clamps. Very good point tho. That pump is rated close to 100 psi or so and standard fuel hose won't cut it.
 
Ken,

thanks for posting those pics.. I'm still figuring out how to route my delivery line while I've got the tub off the body.. figured I'd mount the drivetrain before the body and finish the plumbing as best I can before the tub goes back on.. I hadn't thought of the crossover behind the tub like you did but I like it.

I also like the re-purposing of the coil bracket for the fuel pump, I was getting ready to shop for a strap for mine, but now I'm going to dig through my CJ parts bin and see if I have an extra.

I'd be interested in seeing how you mounted the ECU/PCM into the engine compartment, and some details on your 4-wires to fire and how you splice it.

Congrats on getting this done!
 
Last edited:
This past weekend I attempeted to clean up the mess that the spaghetti monster left under my hood. I pulled out the cj computer from under the dash and pulled that harness through the firewall. I pulled off the split loom and started tracing back wires that were no longer being used and either cut them or unplugged then from where they went. The majority of the stock harness that was a part of the computer control for the 4.2 motor came out in one piece. It is amazing how it cleaned up the engine compartment. Here are some pictures showing all of the wires that came out as well as a couple of under the hood showing where things were mounted and how it looks now. I still have to clean up a few of the plugs the unused bulkhead from the xj but I want to spend some time driving and playing with switches and stuff to make sure I won't need to splice any more wires into the cj harness.


IMAG0481-1.jpg


IMAG0482-1.jpg


IMAG0483-1.jpg
 
I see you kept the PDC, remember that using that provides all kinds of fused battery + and ignition hot circuits that you CAN cut out, but you can also re-use. If you want to get complicated, there's a couple of relays in there that you could also use to switch power to some higher-amp applications.

I left as much wire as I could on each one of those, sealed up the end with tape, labeled them and bundled them up next to the PDC so I can go through and rework a lot of the power feeds using that more modern PDC and newer wires.

I may never use them all, but once you cut them out, you'll likely never be able to rewire it and if you already have the box in there, I think it's worth keeping them. Realistically, if you're just going to cut them all out, you could replace the whole PDC with a couple of relays and a little wiring work and have an even cleaner setup.

Just throwing that out there... looks great and doesn't it feel good to get all that stock wiring crap out? :D
 
That's great to know... I just purchased some new Hella headlights that I am going to be running some higher wattage bulbs in. I was planning on wiring up some new relays to run higher amperage feed to the headlights. Now you've got me thinking. Great suggestion on possibly utilizing some of the relays that are no longer being used in PDC. Hopefully I can appropriate those for my high/low beam feeds to the new lights. I love this site!!! So much information :thumbsup:
 
That's exactly the kind of thing that you can do with them and it's actually a lot simpler than wiring in new relays as long as you ID the wires correctly coming out of the PDC (which is pretty trivial with the wiring schematics, at least it was on mine).
 
Ok... Here is a couple of updated photos of the Scrambler and some more information that may be helpful to someone else doing this swap. My Scrambler had factory air conditioning with the under dash unit. The issue that I ran into in trying to retain the factory air conditioning system and use the compressor from the new xj motor was that there were two different styles of fittings used between the two vehicles. My Cj uses flare fittings on the hoses and the stock compressor from the 4.2. The XJ 4.0 compressor uses a newer O-ring fitting and I needed to find a way to make my hoses work with the new compressor. I could have new hoses made but that would be $$$$. In my searching on the internet I believe I have found a solution in an O-ring to Flare adaptor. I couldn't find any information in the forums of other Jeepers who have performed a 4.0 liter swap offering a solution to adapting the newer compressor to the older A/C system of the CJ. I have not run this setup yet but I see no reason why this shouldn't work. I found the fittings @ http://www.coldhose.com/cat/flare-adapters-22.php and here are some pictures of what the adapter fittings look like as well as a few recents of the Scrambler.


97otofadaperbwjpeg-1.jpg


O-ring to Flare Adapters


IMAG0027-1.jpg


Heated Seats out of a '96 E36 M3. My wife is a huge fan of these.

IMAG0098-1.jpg


Out in the California desert with it's rattle can paint job.
 
Fuel Pump Wiring

You said you had the pump prime but not run and you needed a second wire. Mine is doing the same, I have the one wire hooked up that's ignition from CJ ignition (2 light blue wires) to white/yellow wire to fuel pump relay. Can you tell me what is the other wire that I need to make it run? Thanks,
 
What year motor are you swapping? Both of my wires were green going into the same pin on the bulkhead from the xj harness. I had originally hooked up only one of those wires to my fuel pump and that was when it would prime and run for about 5-10 seconds. I now have both of them hooked up to the one wire running back to my fuel pump and everything works as it should. Maybe the wires are different color from your harness?
 
Mine are different colors, I'm swapping from a 92 YJ. I'm having 2 problems right now. First is my starter is only getting enough power to start the motor once or twice then it only clicks after trying more times. When I turn the key I hear the fuel pump kick on and prime, then go to start and the starter struggles but it will start then instantly die. I've had the battery checked, tried to jump it and tried the battery from my other Jepp and it always does the same. I'm betting I'm having a grounding issue but have yet to figure it out. I'm also thinking that I must need a second wire to the fuel pump to let it run. Any other ideas?
 
I would check your grounds first. And a test probe on your wire to the fuel pump to see if it is getting power after it has started. How did you do your crank position sensor? That could possibly be part of the problem too.
 
After attempting to add the CPS to my T-5 bellhousing with no success I bought the relocation kit from Hesco and its not been a problem. I had it running originally by putting the 3 wires together for power on the YJ harness that I spliced into the CJ harness. Using this method the fuel pump would run no problem and the engine would run great for about a minute or two until it would stall (air issue I think). Since I hooked it up to the CJ ignition switch been having these new issues. Still trying to narrow done the problem!
 
Dubs1856, bumping your thread to see if you had any luck making the XJ 4.0 A/C compressor work with the CJ components using the o-ring to flare adapters. I am finishing up the wiring on my '84 postal CJ8 with the OBDI 4.0/AW4 and am wanting to run the 4.0 AC compressor with the CJ stuff. If you did get it to work, could you possibly elaborate a little more on the setup and what it required, particularly which wires you ended up using! Thanks!
 
A/C is blowing cold still and no leaks. The adapters worked perfectly. There was a single wire that activates the xj compressor and I just tapped into that one with the cj wire at the firewall. I don't remember the colors of the wires on mine and it's all buttoned up and in split loom but you can use a test light to figure out which cj wire in the bulkhead is throwing power when the ac is switched on and then trace the wire back from the compressor clutch on the xj motor and connect them. If you have trouble figuring it out let me know and I'll dig into mine a bit and find out which wires it was. Best of luck!!!

Ken
 
That is exactly what I was hoping to hear Ken! Good to know it is still working well and leak free! Do you happen to remember what size of adapter fittings you needed? The postal is out in the shop and it's -5 without the windchill here outside (don't plan on going back outside tonight) and I don't know the fitting sizes off the top of my head! I think I was definitely overthinking the AC wiring; all I need to do is hook the stock CJ AC compressor wire from the bulkhead directly to the XJ compressor. So I take it all the stock XJ AC wiring that runs to the PDC and ECM can be completely eliminated or did you run the CJ compressor feed through the relay in the PDC? I'm trying to clean up as much of the excess wiring I can. Thank you again!


Sent via signal flare
 
I just called Cold Hose and spoke with John. I was trying to see if I could look up my previous order to find out what I had ordered. Anyways... John was very helpful and said that you would need a #8 and a #10 o-ring to flare adaptor. One for the supply side and one for the return side. The cold hose part numbers for those items are ATC6242 and ATC6243. Those come with the adaptors and the necessary o-rings according to John. Give John a call (800) 223-7167 if you have any questions to make sure you get the correct parts. Best of luck!!!
 
Thank you for taking the time to get the correct part numbers for the fittings! I'm going to get mine ordered this coming week. One last question for you about the AC compressor wiring. If I am understanding you correctly, I just need to take the single wire from the XJ 4.0 compressor and connect it to the original AC feed wire from the CJ bulk head and that is it? Did you eliminate all the XJ AC wires, particularly those that run to the PDC (with the AC relay) and the ECU? I appreciate all the help!


Sent via signal flare
 
I'm reasonably certain that I ran the CJ wire directly from the bulkhead to the XJ compressor. I cleaned up as much of the XJ wiring that I could as well.
 
Dubs,
"Heated Seats out of a '96 E36 M3." How easy an install was this to do? did you need a lot of fab work and did you use the Jeep risers or custom?

Thanks,
Allen
 
It wasn't terrible but was a bit involved. I made custom seat risers which are working but I'm thinking about re-doing the risers to get the seats lower to improve clearance between the seat tracks and the cj doors. My wife appreciates the heated seats.
 
Back
Top