• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Any love for the 304 V8

Kim Dawson

CJ-8 Member
Member
City
Molalla
State
Or
Because the 304 was mostly pre-Scrambler, I don't hear much about them. Haven't had a running one
yet. Do they perform well and get decent mileage, as compared to the 258 or even the 260. Most people
probably prefer to go with a later engine, but I was wondering how well the 304 is liked by someone who
has had them.
 
I had a 304 in my CJ7 Levi Renegade package...Strong motor the PO had short pipes and cherry bombs running out under the passenger compartment so it was too loud for me. The Jeep had auto trans and Quadratrac. I would not say I got great mileage but thats never been an issue with me anyway.. Man I wish I had the Jeep back... :banghead:
 
Thanks for the reply. Sounds like you enjoyed that Renegade. By the lack of response the 304 isn't too popular with the CJ8 crowd. Well, I went out today and bought two of them. One with 20K on a rebuild with an Eldebrock intake, an RV cam, and headers. The other was still runable but on the tired side with a Mallory distributor and headers. Both had bellhousings, one with the trans mounting surface about 7 inches wide, and the other at 10 inches. I guess the wider mounting will give me more choices on transmissions. Now I can find out how I like the 304.
 
I like the 304 a lot. Sound awesome, torque, v8 cool factor. Quite a few people on here have them. I believe there would be more, but the 258 is super solid and the 4.0L swap is relatively easy and nets drivability.

I think if I were to AMC V8 swap I would go 360. Availability is higher, 4 barrel carb intakes more common and TH400 (common)/T-176 compatible. Of course there goes the MPG.
 
I have a 304 in a 1978 International Harvester Scout 2, don't know if is the same or not. I have never been in the engine. When I bought it in 1982 it had 114,000 miles on it. and a broke odometer. I can't even imagine how many miles it has now.
 
Thanks for the replys. Good to know there are some kind words for the 304. I'll put the low mileage one in a CJ8 parts pile I picked up and keep it all AMC. My 83 GMC has a 305 and it has lots of power. Is the SBC that much different than the 304?
 
Thanks for the reply. Sounds like you enjoyed that Renegade. By the lack of response the 304 isn't too popular with the CJ8 crowd. Well, I went out today and bought two of them. One with 20K on a rebuild with an Eldebrock intake, an RV cam, and headers. The other was still runable but on the tired side with a Mallory distributor and headers. Both had bellhousings, one with the trans mounting surface about 7 inches wide, and the other at 10 inches. I guess the wider mounting will give me more choices on transmissions. Now I can find out how I like the 304.

No response didn't mean I don't like em. :wave: About the best driving combo to me in stock form is a 304 with a t-150 3 speed in a little CJ5. I don't have any in a scrambler. But I sure do like that light rumble of a factory 304. I had a Quadratrac 304 auto once in a CJ7 tho and didn't like that but that wasn't the fault of the 304 tho :bacon:


 
I love my 304 in the CJ5... as Eric said, the combination of the T150/D20 and that 304 with 3.54 gears on 33's really does very well together.
I fuel injected mine as well, so it starts without pumping everytime!

I just wish I could drive it more... the CJ5 and the kids/wife, doesn't work out as well as the CJ7 does... and soon the Scrambler... just keep getting larger and larger (room wise).

cb
 
(The International 304 is NOT the AMC 304.) I love the 304! I ran one for many years until I needed some valve work, at which point I just moved on up to the 360 (and eventually the 401). The 360 is probably more common though which is why you hear about them more often.
 
My old '76 CJ7 Levi had the factory 304 in it. I now run a 304 in my '81 Scrambler. The '82 will have a 360 in it just to be different and I found it cheap.

Nothing against anyone's builds on here but for me I have to stay AMC.
 
Absolutely nothing but LOVE for my 304s, I've had probably 7-8 over the years. Great engine never had much issue except the 1st one I put in the Scrambler, but more my fault for trusting the PO vs. me looking into things before I installed it. Lesson Learned! The one I currently have in the 8 has had some work done to it, not sure what, but it's got a whole lot more snort to it than any of my others.
 
Thanks for the reply. Sounds like you enjoyed that Renegade. By the lack of response the 304 isn't too popular with the CJ8 crowd. Well, I went out today and bought two of them. One with 20K on a rebuild with an Eldebrock intake, an RV cam, and headers. The other was still runable but on the tired side with a Mallory distributor and headers. Both had bellhousings, one with the trans mounting surface about 7 inches wide, and the other at 10 inches. I guess the wider mounting will give me more choices on transmissions. Now I can find out how I like the 304.

Check that intake, if it is the SB2 by Edelbrock take it off and toss it in the scrap pile... That thing is worthless, flow sucks and it robs power. It was an attempt to comply with the EPA regs that started coming out in that time and well, it didn't work out very well
 
Intake has Torker on it. Good to hear there is love out there for the 304. Now I'm even more excited about picking these up. Thanks for the replys and the combinations that you have found work well with the 304.
 
Torker works well on it, give a bit more low end, one thing that most 304s are lacking g on compared to the 258. My set up is 304/T18a/Dana 300 twin stick w/ Terra low 4:1 kit, and I'm running 4.11 gears and 36 tires. I can run down the interstate with out issues and crawl just about anywhere I want to. You'll be able to get a lot more wheel spin out of the 304 also, if you plan on playing in mud.

Sent from my HTCD200LVW
 
I had a buddy when I was on the east coast who picked up a 304 to put in his 7. It was his first engine swap, so I came over to give him a hand. He handled the mop-up of getting all the little things reattached after I left, but the next time I saw him, he could lift a front tire off the ground when he dropped the clutch. It had the Edelbrock "Performer Package" consisting of the Performer intake, 600 cfm carb, and Performer-Plus cam, and was otherwise stock: stock ignition, stock heads, stock bottom-end. I was REALLY impressed with what that did for the 304 compared to my stock 304. (Everyone on IFSJA stays away from the cam on a 360, but I really think Edelbrock made it with the 304 in mind.)
 
The PO of the 304 with the Torker intake kept the carb. Would 600 cfm be what it was intended to use? The headers that were used with that one were the out-the-fender-well type. I'm not sure I want to go that route. The other 304 has headers that tuck inside the frame. I figured I'd use those, although the PO said the others would give more power. Anybody have any thoughts on which way to go with the headers? Thanks for your thoughts and expierences, guys.
 
I personally did not have any luck with headers on the 304 in the '76 CJ7. They were in-frame and for the life of me I could not keep the heat down. I even had them wrapped professionally by a local race shop (thinking maybe they had some special magic versus when I wrapped them). after constantly fighting with high heat I switched back to factory manifolds and didn't have high heat issues again. I honestly didn't notice a power loss.

based on that experience alone I went with factory manifolds on the 304 in my '81 and plan to do the same with the 360 for the '82.
 
Unless you plan on building a monster HP engine the difference between the headers and factory manifolds will not be enough to really notice on a close to stock engine. I've never had a set of the inside the frame, so can't say anything on them, I am currently running the outside the frame with hooker purple hornies, only real draw backs are I can't put my factory aide steps on due to clearance issues and tires rub the header at full turn, other than that I like them.

Sent from my HTCD200LVW
 
Doug Thorley Tri-Ys (inside the frame) for the win!

Short of those, I like the factory high-flow manifolds.
 
You will always get more power from optimizing the timing and jetting... just saying- 😉

Sent from my SM-G920V
 
Back
Top