• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Can't Buy It so I Built It

No, I worked with Bill over there and he based the spring design off the specs that I was building too. 360, 35s, winch, etc. I also went with the orbit eye shackles that are supposed generate more flex with less bind. We will find out. Here's a link to my build thread.

Man your scrambler is nice! This community is such an inspiration and motivator for me. It's really cool to see how others have done their projects.

That's good to know about the Alcon springs. I'm definitely considering this option if I decide to go bigger. It would be good to know that the springs are designed for the exact weight. I have an old 8274 winch I rebuilt for my old XJ I had. It definitely sagged the front end down on it but it also rode so much nicer with the extra weight up front. I'm not planning to add the winch just yet. I'm leaning towards building it more stock and then deciding later what things I want to upgrade. The temptation is always to go bigger but that always starts to snowball into other things to upgrade. I'm really leaning towards even going with a stock YJ leaf spring and 31s. If I decide I need to go bigger in the future that stuff is easy to change.

I'm thinking the Alcon springs would be the way to go if I build a camper on the back. I'm starting to see this build as 2 phases really. Phase 1 is getting it on the road, camp and travel with it. Then decide what changes I want to make and plan for phase 2.
 
I would recommend to take your time and make sure that phase 2 doesn't replace new parts purchased in phase 1. Take this from someone who has ran stock height up to a 4" BDS lift and tires from 31-37". Personally my vote would be for a 2.5" OME, BDS, Alcan or Rubicon Express (in no particular order) lift spring with a 33" tire. I would probably look at a 3.73 axle ratio with that.

I bet everyone on this forum thinks you need to mount that 8274 on your 8. They just look right.
 
I would recommend to take your time and make sure that phase 2 doesn't replace new parts purchased in phase 1. Take this from someone who has ran stock height up to a 4" BDS lift and tires from 31-37". Personally my vote would be for a 2.5" OME, BDS, Alcan or Rubicon Express (in no particular order) lift spring with a 33" tire. I would probably look at a 3.73 axle ratio with that.

I bet everyone on this forum thinks you need to mount that 8274 on your 8. They just look right.
Yeah I agree, replacing new parts a year or two down the road wouldn't be ideal. I'm going to keep an open mind until I'm ready to order the parts. I'd like to build my own front bumper for the 8274 in the future. It'll definitely make it's way on there then.
 
I would recommend to take your time and make sure that phase 2 doesn't replace new parts purchased in phase 1. Take this from someone who has ran stock height up to a 4" BDS lift and tires from 31-37". Personally my vote would be for a 2.5" OME, BDS, Alcan or Rubicon Express (in no particular order) lift spring with a 33" tire. I would probably look at a 3.73 axle ratio with that.

I bet everyone on this forum thinks you need to mount that 8274 on your 8. They just look right.
They really do!!

761C20C8-6506-41EF-A1C7-1493A4BB0B58.jpeg
 
So I'm starting to have second thoughts about having my TDK frame galvanized and I am looking for some input. It doesn't ship from TDK to the galvanizing plant for a couple more weeks yet. When I originally placed the order I figured it was better to go with the galvanizing now since it seemed like better protection for the frame. But now I'm concerned about two things:

1. It seems like people have trouble getting paint to stick to them, even with proper preparation taken. I don't think not painting it is an option either since I don't want that shiny galvanized look.
2. I'm going to need to weld things to the frame too like motor mounts and potentially other modifications.

Originally I was thinking even if I need to remove some galvanizing to weld to the frame that the inside would still be protected. But now I'm not so sure it's a good idea. The TDK frames are already going to way outlast the old ones and chassis paint would do a pretty good job at keeping it protected too. What do you guys think?
 
Unless you plan on parking in the ocean from time to time, I'd say nix the hot dip. Galv is a pain to do any post-dip work to, and I think a well prepared, well laid paint job even without zinc will outlast the treatment the OEM frames got from the AMC assembly process. There are also far less impingement spots on the TDK frame for crud to accumulate, so the rot should in theory be less of a threat in general.

I don't have anything to base this opinion on other than being a general hack-job fabricator and enjoying the possibility of burning on random pieces of metal without developing lung issues, and covering my shoddy work with a cheap and easy rattle can treatment. I also have a tendency to rock rash, and scraping off a long streak of galv seems counterproductive.
 
Use properly applied paint to include surface prep and then follow with fluid film and cavity wax. Watch a video on the making of G Wagons, they add Cosmoline to their frames.
 
Unless you plan on parking in the ocean from time to time, I'd say nix the hot dip. Galv is a pain to do any post-dip work to, and I think a well prepared, well laid paint job even without zinc will outlast the treatment the OEM frames got from the AMC assembly process. There are also far less impingement spots on the TDK frame for crud to accumulate, so the rot should in theory be less of a threat in general.

I don't have anything to base this opinion on other than being a general hack-job fabricator and enjoying the possibility of burning on random pieces of metal without developing lung issues, and covering my shoddy work with a cheap and easy rattle can treatment. I also have a tendency to rock rash, and scraping off a long streak of galv seems counterproductive.

I had mine dipped and with a little clean up, it painted up well. But, I did it for the inside of the frame not the outside and living in Michigan, you might as well be sinking it to the bottom of the ocean. But in truth, it will never see the salt again anyway. But do it once, do it right.
 
Thank you guys for all the input on this. It gave me quite a bit to think about. The jeep is by no means going to be a daily driver in the winter but I do think it will see some salt. I don't want a little bit of salt to keep me from a trip in this thing. But ultimately I made my decision after talking with TDK on the phone. After speaking with them I've decided to skip the galvanizing. They strongly suggested to skip it if I'm planning to weld to the frame and also agreed with the difficulty of painting it. The plan now is to paint the frame inside and out then use protective coating like fluid film on the inside.

On a lighter note, they also mentioned that they are ahead of schedule right now and with skipping the galvanizing my frame should ship next week!
 
Thank you guys for all the input on this. It gave me quite a bit to think about. The jeep is by no means going to be a daily driver in the winter but I do think it will see some salt. I don't want a little bit of salt to keep me from a trip in this thing. But ultimately I made my decision after talking with TDK on the phone. After speaking with them I've decided to skip the galvanizing. They strongly suggested to skip it if I'm planning to weld to the frame and also agreed with the difficulty of painting it. The plan now is to paint the frame inside and out then use protective coating like fluid film on the inside.

On a lighter note, they also mentioned that they are ahead of schedule right now and with skipping the galvanizing my frame should ship next week!
Sounds like the right choice for you. You definitely want to be done with any frame work before galvanizing. I had mine dipped after doing all of the repairs, etc then had an experienced shop powdercoat it. It was a no-brainer moving to the tropics where the air is like a continuous salt bath. I had pretty much everything that could be galvanized done.
 

Attachments

  • 32202659_10213992650509016_7032144580736712704_n.jpg
    32202659_10213992650509016_7032144580736712704_n.jpg
    58.7 KB · Views: 10
The Carribean is brutal on ferrous metals. Even stainless will rust. Aluminum gets corrosion and electrolysis.
 
Just an update for anyone looking to follow my Instagram, I've changed it to @TheDustyRag to keep all the profiles consistent.

I'd update my first post but it seems I can no longer edit posts. Does anyone know how to edit a previous post?

I'm also missing the like button on others posts too.
 
Been a few weeks so I wanted to give an update. It got pretty cold a couple weeks ago so I decided to pick something to work on I could do inside. The old heater and vent air box needed some attention so I tore them apart and made all new seals, new heater core, removed the old tenants belongings, cleaned and then painted everything. I was going to do a write up on this but I followed this guys video and parts list here and he already did a really good job at documenting everything needed. I'm really happy with how everything turned out too. Only thing is that the cage wheel he recommends isn't the right size. I believe it's the one that would have came with an AC optioned cj. I'm not sure what the right part number would be if it's out there but I can tell you it's not J8126991 or 35602. You can probably guess how I know. Mine was in decent shape so I ended up just reusing it. Other than that it went really smooth. Oh and I also upgraded to the chevy blazer motor PM102 too.IMG_6129.JPEGIMG_6133.JPEGIMG_6140.JPEGIMG_6144.JPEGIMG_6152.JPEGIMG_6160.JPEGIMG_6181.JPEGIMG_6225.JPEGIMG_6287.JPEGIMG_6304.JPEG
 
Oh and I can't forget. The frame is here! Man is this thing pretty too! Now I'm trying to decide how I want to paint it. I think I'm going to do that here soon. I'd really like to hear your thoughts on what's worked for you. Right now I'm considering using something like POR15 to straight bare metal or possibly epoxy primer first and then a topcoat. Not sure how I want to go about it just yet.
IMG_6541.JPEGIMG_6546.JPEGIMG_6525.JPEGIMG_6521.jpeg
 
Epoxy Primer and top coat. I'm not a fan of por15. But also they use por15 more for rusted metal, not new metal. Also epoxy/paint the inside first (that's where most of the rust forms, once it's there it's hard to kill).
 
Back
Top