• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Curious about the Klune V underdrive......

mtruckstuff

Back Home in Colorado
City
Loveland
State
CO
Anybody have any direct experience with these? Thought about maybe putting one in a rock unit along with my NV4500 and a 225 Buick.

Paul
 
Have installed a bunch of them. Excellent product. Never seen one break. About 8 inches long,cable activated 2 to 1 or 4 to 1. What else do you want to know?
 
Interesting thing to note with this is it can be used as an adapter from tranny to t-case. Interesting option if you're looking at a setup that would otherwise require an expensive adapter.

I've "fantasy built" rigs that included these :D
 
Eric,
Good point!

Rig in question is a "fantasy" rock build right now, too. I've run my son's '71 with a 225 Buick and it's a great motor. Light, decent highway power and good grunt down low, easy to work on and lots of power possibilities. Should be simple between an NV4500 and D300. My biggest concern is getting from the Buick to the 4500. I'm not sure if the Buick runs a typical GM bellhousing pattern. If it does, it should be a snap. GM input shaft (I have a Dodge tranny) and 4WD tailshaft housing (mine is 2WD) and I should have it.

My other option would be 225/NV4500/D18/Warn OD, but would require an offset rear end. This scenario would skip the Klune.

Ahhh..it's fun to dream;) ;)

Paul
 
The 225 is the standard GM BOP pattern bellhousing. Those 225s are great low end motors, but the heads stink (sorry). I raced one until the 231s came out. The 231s had what were called 'high port' heads, they flowed better the Kenne-Bell Stage II aftermarket heads, that cost a bunch back then....but then again, I was trying to go fast. At the time, I switched to a Chevy 229, because I thought parts would be easier...boy was I wrong.
 
How about the 231 Odd-Fire from '75 to '79? I kind of like the goofy lope at idle.
Paul
 
Klune-V

I run one in my Scrambler. Have been for about 4 yrs now. I can tell you that i broke it the 1st time out. I broke the shaft between the tranny and Klune. It went from 32 spline to 23 spline (I think or something like that). It was a square cut shoulder and it snapped right there. They warrantied it and i upgraded it and have not had any troubles with it since. I have gotten used to it now and it works really well.
 
mtruckstuff said:
How about the 231 Odd-Fire from '75 to '79? I kind of like the goofy lope at idle.
Paul
Those are the same BOP pattern and "I think" with the good heads.
 
Scott Mine said:
I run one in my Scrambler. Have been for about 4 yrs now. I can tell you that i broke it the 1st time out. I broke the shaft between the tranny and Klune. It went from 32 spline to 23 spline (I think or something like that). It was a square cut shoulder and it snapped right there. They warrantied it and i upgraded it and have not had any troubles with it since. I have gotten used to it now and it works really well.

i got one but never used it much maybe 6 hours in my old jeepster with 220hp 4.3. Mine is a 4-1 23 spline in and out to the dana300.

Scott Mine do u think i can make it live behind a mildly built 300hp small block and auto as long as i dont get on it in 4-1
 
Hold Up

I have behind a small block and auto right now. I do get on it more and more each time i get out. Did you splined shaft neck down from the Klune-V spline ( I think 32) to the 23 spline dana 300? If so did it have a square shoulder? That was how mine was and i broke it with the straight 6. I think as long as it is not a square shoulder then i think you are alright. How longa ago did you buy this?
 
Scott Mine said:
I have behind a small block and auto right now. I do get on it more and more each time i get out. Did you splined shaft neck down from the Klune-V spline ( I think 32) to the 23 spline dana 300? If so did it have a square shoulder? That was how mine was and i broke it with the straight 6. I think as long as it is not a square shoulder then i think you are alright. How longa ago did you buy this?

ive only had it for a year and a half and i dont think the shaft was cut like that so i might be ok
 
Shaft

Yeah ... I bought mine about 4 yrs ago and that was when they were first coming out. So i know that they have gotten better. If they did not and you break it then have an excellent warranty and they will work with you.
 
Back
Top