• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

First CJ8!

oldschoolnewcj8

Basic User
City
ocala
State
FL
hey guys I'm new to the forum and just thought I would share my scrambler. I found it on craiglist but the guy said he wanted to trade for an f250. well i had a 92 f250 4x4 gas (had some major body damage) that I used to haul the garbage off and hardly ever used. hopefully I didnt get ripped however I've always wanted a scrambler and the cost as you know does not matter then. Here's some details: 1982 cj8 scrambler, remanufactured 258 by titan motors in ocala florida with around 5000 miles, bored to about 263, 2bl weber carb, dui distributor, and hedman headers, 3inch body lift, almost bald 33x12.50s. Custom diamond plate dash. the frame is in okay condition, few rust and bend spots, it has been plated on both sides of the frame for half of it. The guy that owned it cut out all the rust on the floor board and fiberglassed all of it. He replaced the rear bed with thick diamond plate. the rear quarter panels have a few small rust holes and the two biggest rust spots/holes are under the door jam on each side. but all these rust holes are covered by diamond plate rockers and corner protectors. the only problem is that the t14 in it is bad and will not go into any gear. so he included a t18 with granny low and dana 20 tcase to go with it. He says its a jeep t18 but im not sure. and im not sure what all parts I will need to put it in besides different length drive shafts. any help on that would be appreciated. well heres some pictures of her!

c1c5a554-1.jpg


b14a36ea-1.jpg


3d3f7288-1.jpg


its also missing the small panel that the tailgait hinges bold to so its kind of just hanging there :mad:

78c03144-1.jpg


ae3eb524-1.jpg


b8ce9250-1.jpg


She is a little ruff but I plan on putting plenty of tlc into her. First things for it are going to be seats and front fenders, as well as re-painting a few things. I just bought a spring over axle lift and I am currently in the process of putting that on. Thanks for looking, hope you like her! :rotfl:
 
Last edited:
This is how she currently sits. I am in the process of putting the lift on (well all I've done so far is take everything apart) and got stuck because I have to go buy a pickle fork to get the drag link off the pitman arm.

IMAG3165_zps35ad81b0-1.jpg
 
Welcome to the family. You'll love it. Much advice and info here. We like pics; keep 'em coming with the build. What are your plans for it? I'd say you did great on the swap btw. Any questions you have, just ask. There's a wealth of knowledge here. Again, welcome aboard.
 
Congratulations on your new Jeep. Lots of help can be had here. Good luck.
 
thanks, looking forward to working on it, especially with this 90-100+ weather slowly going away here in Florida. I am trying to get the jeep ready for my local jeeptober fest here in ocala. Only two more weeks. not going to get much done. :banghead:
 
oh and as for future plans, for now its just going to be a trail jeep as i slowly work on things and find the different missing parts. then down the road I am either going to keep it for a while and restore it or make it my daily driver and turn it into one bad machine.
 
It's a scrambler, therefore it is already a bad machine. As you fix it up and dump big $$'s into it, the level of badness will increase exponentially. You will be keeping the girls away with a stick....

:)
 
I'd say you did pretty well if the work on the frame was done right. The T-18 + Dana 20 is worth $500 on its own if it's a Jeep T-18 or a Ford T-18 that's already been converted. They're hard to find either way, and if it's a converted Ford you may even be better off as parts are easier to come by. Check the casting numbers on the case, plug em into Google, that'll tell you what it is. Good news is, you can get EVERYTHING for these vehicles. You could literally build one out of aftermarket parts. Welcome to the club!

As far as parts for your T-18 swap, check out Novak Adapters. They have a writeup on it I believe. When I did mine, it was a Ford T19 (T18 with a synchro 1st). All I needed was a new pilot bushing that Novak sells, different length driveshafts, a Ford clutch pack, and I had to drill new holes in my transmission crossmember. That was it. This is assuming he gave you the correct bellhousing. If not, I'm not sure if you can re-use your T14 bellhousing with modification or if you will need to get another one. If you need to replace your pilot bushing (if it's an adapted Ford), you may have to take out this small bushing inside the end of your crank in order to make the Novak bushing fit. It's like 1/16" thick and the stock AMC bushing sits inside of it. I had to notch it and tap it out with a hammer and chisel. If your tranny is a true Jeep T-18, I think it should bolt right up with your existing bushing and clutch pack, although check the clutch pack for wear. They're cheap and while you're in there you might as well replace it if it's looking tired. If you're looking for driveshafts instead of altering your existing ones, look for shafts from a factory automatic transmission. They should be close/exact fit, but always measure first. As an alternative, there are several driveshaft shops online who will build you a better than stock new shaft for what it would cost for your existing shafts to be altered and rebalanced. When I looked for mine rears were $150 brand new from a shop in CO that advertises on eBay. I think there was another in NJ as well. Sometimes you will also have to drop your cross member with some 7/8 bar stock as spacers. I didn't have to do this, but some people do have to depending on their setup.
 
Last edited:
Back
Top