• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Hinges?????

gaducker

Legacy Registered User
City
Newnan
State
ga
I am tearing down for paint now and need yalls opinion. Paint hinges body color or get stainless hinges and related hardware? Some stainless kits I have seen don't seem to be built as well as factory hinges.
 
I'm a factory paint guy....unless the rest of the jeep has a bunch of other chrome and bling.

I feel the stainless hinges just jump out too much, slap you in the face and say "HERE I AM"
 
I've got my cj8 in primer and about ready to paint, but mine is being painted in pieces. If I paint the hinges separately, it will be hard to install without scratching or peeling the paint. I've also acid dipped the hinges and the rust still tries to work it's way out of the hinge. On my cj7 I did, I used stainless windshield hinges and have no problems (I leave the windshield up, so they do work well). I like the look of painted hinges so I might try to take the stock hinges apart to get all the rust out, then paint them. If that works, I might try to put her together painted. If any problems, I wouldn't think twice about using stainless for durability.
 
I have "Get rid of stainless bits from PO" on my list if things to do. So my vote would be body color.
 
Factory hinges are built much better than any aftermarket stainless I've ever seen.
 
Body color. I hated how the PO put all black hinges on my red Scrambler.


 
I repainted mine body color and had no problems when installing them. I put a small amount(very small) of grease on the screw heads so it wouldn't mess up the paint.
 
heard a layer of tape around the torx bit during re-installation will reduce damaging the paint.
 
I certainly prefer the hinges to "disappear" into the paint finish, by painting them the same color as the body. The "strap" or "band-aid" appearance of different color hinges looks too unfinished or like a cheap assembly, to my eye.

This may be a poor question, but why wouldn't a painter paint the body pieces and corresponding hinges separately and then assemble them before applying one or two final coats of paint, besides it being more labor intensive? Note: The hood, tailgate and windshield would include hinges applied during final paint application, but not also applied to the body, for obvious handling reasons. So, for lack of a better description, it is a partial assembly.

I've never disassembled any of these body pieces, and I am not familiar with how much assembly was done at the factory prior to painting. Although, I have read about the bare metal behind hinges; I'm trying to envision how the hood, tailgate and windshield could have all been assembled onto the tub in a paint booth at AMC, as that doesn't seem possible/practical.

For example, the doors with hinges applied and corresponding tub hinge female leaves are simple, because the hinges slide into eachother (i.e. removeable pin). However, I've never closely examined the windshield, hood or tailgate hinges to know whether they disengage from each other at the hinge barrels, or if they are a "non-removeable pin" type of hinge that require one side of the hinge leaf to be unscrewed from the body?
 
Yes, the fact that it is more labor intensive is the main reason. And put me on the anti aftermarket hinges bandwagon for sure....

I have pics I can dig up of a complete jeep CJ body rolling down the assembly line with the doors and w frame hung and painted as all one assembly. Also dipped in a bath earlier down the line. The doors are propped open and the windshield frame tilted forward about 45 degrees. The whole thing then gets shot inside and out.
 
...a complete jeep CJ body rolling down the assembly line with the doors and w.s. frame hung and painted as all one assembly. ...The doors are propped open and the windshield frame tilted forward about 45 degrees. The whole thing then gets shot inside and out.

Wow, that would be an interesting thing to see. So, the hood hinges are the only hinges applied afterwards, since I would suspect the tailgate was also anchored to the tub just as were the doors and windshield.
 
Wow, that would be an interesting thing to see. So, the hood hinges are the only hinges applied afterwards, since I would suspect the tailgate was also anchored to the tub just as were the doors and windshield.

When I took apart the original paint "Yard Scrambler", the part of the hood/cowl that was under the hinges WAS NOT painted, just like the areas under all of the hinges:thumbsup:

If I had an original paint CJ that was in excellent condition, I would seriously consider pulling all of the hinges/front fenders to tub/fenders to grill and painting, before problems start:twocents:
 
...I would seriously consider pulling all of the hinges/front fenders to tub/fenders to grill and painting, before problems start:twocents:

Geez, you think they even had the front fenders and grille installed on the paint line? However, I suppose that wouldn't be any different that any other pickup truck...just lower and slide the motor into the engine bay. So, everthing except the hood and top was installed before going through the paint line?
 
When you paint all the parts and then put them together, any bolt head that tightens against a new painted surface can chip or peel the surface (especially the windshield hinges). You would have to touch these spots up with a brush which would not look good. Especially if you went to a lot of work to do it right. If the finish was baked on (like a factory finish), it would hold up better to the tightening of the bolt. Amc put the jeeps together, then painted. The joints and under the hinges on the jeeps I've taken apart didn't even have primer on them (not that it would have held up since back then they used lacquer primer which absorbs water). I've never tried the grease under the bolt head. If that works, that would be great since I like the painted look also.
 
Geez, you think they even had the front fenders and grille installed on the paint line? However, I suppose that wouldn't be any different that any other pickup truck...just lower and slide the motor into the engine bay. So, everthing except the hood and top was installed before going through the paint line?

On the "Yard Scrambler", which is an '83, yes, it appears to me the grill/fenders/hood/tailgate/doors/windshield frame were all bolted to the tub before paint. But, this is speculation on my part, but then again, why else would all the body tub metal be "bare" at these locations:shrug:

On my red Scrambler, when I repainted, I had all the body parts, including hinges, painted separately. I wanted to make sure every square inch had paint. But, in doing so, all of the pieces do not match 100% perfect. For a "trail" jeep, looks perfectly fine to me:twocents:

But, to do it "right", and get a "perfect" finish, you would have to prime/first coat in separate pieces. Then, assemble everything, bring back for final paint and clear. This would give the "best" finish, but would also cost the most, in both time and money:twocents:

If/when I ever repaint my Sherwood green Scrambler, that is how I am going to do it: prime/paint separate pieces, reassemble, final coat/clear last. You could probably get by finish painting the underside/inside before reassembly. It would be about impossible to stand back and say: "Hey, that under body paint above the drive shaft is about 2 shades off from the hood":rotfl: You would never be able to see both pieces simultaneously. However, a hood/door/tailgate to body tub side difference will really stand out:twocents:
 
Yes that picture I have has the hood and grille installed too, and the hood is propped up about 20 degrees. I need to get it out tonight and take a pic.

The few that i have restored for others I had all the pieces done in primer individually at my paint guy and then reassembled onto my frame at home for fitment and to align the hood fender door gaps etc. Then the whole thing taken off as one unit and put onto a frame carrier dolly thing i made and then off to the painter again. The frame dolly is a cj frame with an extended tounge and no front axle that allows it to be towed like a single axle trailer. This way I tried to mimic what the factory did to get no turning of torx bolts or any variation of color change painting the parts piecemeal. And the frame dolly catches all the overspray the painter likes the fact he doesn't have to mask anything and the end product is a fully assembled painted tub.
 
I got some paint in a spray can from paintscratch.com, took hinges off and painted under them and the backsides of the hinges, THEN took the Jeep to paint, so when he prepped the Jeep he sanded the area all around the hinge and the top coat covered everything, and I had the peace of mind knowing the backside of the hinges and underneath them were painted.

The jeep looked pretty sweet before paint. I drove it around with primer black front clip and windshield frame, copper paint, with 3A beige spots all over it where the hinges were.
 
Back
Top