• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

hot running 360, cooling ideas

revho

$9.00 vanilla malt
Lifetime Member
City
beaverdam
State
MI
Took it out for a maiden voyage last night. Half hour drive and got back to hear the coolant over flow res boiling. So....looks like I will need an alum radiator and possible taurus fan upgrade before too much driving. The original radiator was suspect going back in anway as it looked somewhat dirty and plugged.


She sucks some gas now too with that 360... you can watch the gas gauge go down. Literally.

Any input from people that converted their I6 to a hot running 360? did you do a cross flow aluminum 2 core or go with a 3/4 core aluminum? Downflow or cross flow? This is an auto with the TF999 as well.

Thanks,

Kevin
 
Last edited:
If you haven't already tried it, I did a radiator flush on a hot running Ford Econoline 150 van. It made a huge difference. I couldn't run the A/C before because it would overload the engine. After the acid flush it ran like a champ. The junk that flushed out was unbelievable. It may be worth a shot as it's cheap and easy to do.
 
I've got the 360/TF999 also, my cooling seems to work well. I've got a stock type 3 core that I put in new with a stock ('81 304, CJ-7) fan shroud and the stock 360 Waggy fan.
 
I've got the 360/TF999 also, my cooling seems to work well. I've got a stock type 3 core that I put in new with a stock ('81 304, CJ-7) fan shroud and the stock 360 Waggy fan.

Ive been reading from other forum searches that a fan shroud is pretty key as well to keep the header heat as well away from the radiator. I was also told that a taurus fan upgrade wouldnt do as much as the stock fan on the 360 in regards to pulling heat out.

Good stuff so far.
 
OEM 3 core radiator and OEM shroud for V8 works great for me. I tried a home brew shroud and electrical fan in the past but it didn't work nearly as well.
 
When I lived in DC, I ran a stock 3-core with a 360 and a FlowKooler pump (no shroud) and never had any issues, even during the hottest days in July. When I jumped up to my 401, I went to a replacement copper 4-core (I forget the brand, but still have it in my Jeep) and added a fan shroud. Never had any overheating issues.
 
Also, dont run the tranny cooler through the radiator. Get a separate tranny cooler. As above, shroud is key.
 
Also, dont run the tranny cooler through the radiator. Get a separate tranny cooler. As above, shroud is key.

I currently have an individual tranny cooler but it is mounted on the radiator. Is there a better spot to put it?
 
I currently have an individual tranny cooler but it is mounted on the radiator. Is there a better spot to put it?

Mine is mounted to the radiator, too. No problems from it. He's saying not to run the trans cooler line through the stock cooler loop in the bottom of the radiator.
 
Roger that. From the sounds of it then I will start hunting for a cj 304 fan shroud and new radiator. From the sounds of it, a 3 core oem would be fine.

Thanks everyone.
 
I picked up a reproduction shroud from OMIX-ADA. I don't remember the vendor I used.
 
Question for you all again on this one. Had the day off today so I pulled the old radiator. When I took the top hose off I looked in. the hose and the inside of the hose had rust colored radiator fluid. Drained that out and noticed the hose had a coiled spring inside, assume to keep the hose from collapsing? Have I just not noticed this in a hose before and it is common? The rusty antifreeze didnt look good either.
 
Question for you all again on this one. Had the day off today so I pulled the old radiator. When I took the top hose off I looked in. the hose and the inside of the hose had rust colored radiator fluid. Drained that out and noticed the hose had a coiled spring inside, assume to keep the hose from collapsing? Have I just not noticed this in a hose before and it is common? The rusty antifreeze didnt look good either.

The spring is common, and is exactly for what you intuited. Rusty antifreeze is bad. I'd suggest a chemical flush.
 
The biggest thing you have to learn about the cooling system is that it IS a system. You can't just tweak one thing, and of course it does not help that as a car community we tend to pass around individual nuggets of information, but often not the whole story. You can kill yourself by listening to good advice in isolated fashion, even when individually many of those nuggets of truth are based on some truth. Whenever I find myself getting in a jam, I ask myself if I have quietly started acting in a thinking pattern I call "monkey see monkey do". Meaning, I'm taking individual nuggets of info and not getting to the fundamentals of "why" I'm doing something. Sometimes it sneaks up on you. We are all guilty from time to time.

First, aluminum in and of itself does not necessarily make for a better radiator. Aluminum works very well, especially in race vehicles that receive large and constant volumes of air delivery, but its not the best material for heat conduction. A traditional copper radiator actually has better heat transfer, all other things such as size being constant, so if you are in a jeep that is crawling at low speeds you may well be better off with copper when sustained airflow is not present constantly. The blind choice of aluminum is not as simple as many make it. (I actually took out my aluminum radiator just for the reason that extended slow trails would be part of my requirements)

Fan sizing is another one. Many guys will grab an electric fan and like my jeep was when I purchased it, there was a pusher on one side and a puller on the other. They covered the very same portion of the radiator, so when running they worked together, but only covered a relatively small portion of the overall square inch size of the radiator facing. Fans have a fixed pitch, once they are pushing air at the rate of that pitch, adding another fan covering the same area essentially does nothing. The job of a shroud is to force the airflow over the entire area of the radiator, not just the portion the fan is covering. Trying to just add electric fans without a shroud or a plan for airflow will just not get you there.

Going further, an automatic transmission can generate loads of heat. In one way or another, this may be putting a sizable extra load on your cooling system, especially if you are pushing bigger tires/lift etc.. Transmissions need cooling too, and if you have it routed through your radiator, you could actually be pushing up your engine temps. That's why some say to not use a transmission cooler internal to a radiator. I won't directly refute that, but will instead target the main issue being the total cooling capacity of the transmission and radiator combined. In many cases, you need to increase this and the best way is to add an external transmission cooler. It's best placement is usually in front of the radiator and sized appropriately will not only bring your transmission temps down but add capacity to your engine cooling as well by removing the need for your radiator to work overtime. Most transmission shops recommend routing this additional cooler through the radiator transmission circuit as well, and so long as the overall cooling capacity is sized appropriate this will work fine.

We have not even touched on quality hoses (old hoses can be collapsing internally), or pump efficiency (you may not want to spin a pump faster than the stock water pump pulley as coolant needs to sit in the radiator long enough for heat transfer to take place, thermostat temps (lower is not necessarily better) etc... So hopefully you get the message that a cooling system is just that, a system, and you can not address it by looking at one piece at a time. This is very much a weakest link sort of situation.

Most troubleshooting on an engine is best done as holistic systems (ignition, fuel delivery, braking, etc..) and your cooling system is no different. When you address it, address all the components in it together.
 
thanks Ghostwave for the very informative post above. Some mod might want to sticky just this tech info.

Diving deeper into what I have, it is a 360/999 auto/300. I have a basically new copper 3 row radiotor and OEM V8 CJ fan shroud. I already have an external tranny cooler that was mounted to the old radiator. Currently I have 34x10.5x15 tires with stock axelsand gearing. Axels and gearing are later on down the road.

Based on what you have typed above, I should be in a better place now, correct?
 
This was in its maiden voyage...was the motor setting for a length of time maybe empty, meaning no coolant in it? But if you noticed rusty color, I would suspect your radiator is now full of rusty scale from the engine, and the flow is impeded hence the boil over... I would take it to a shop and have it boiled out. Flush out the motor without the heater or radiator hooked up other wise you'll flush all the loose crap back into it.

I dont think this will help the gas mileage though LOL
 
This was in its maiden voyage...was the motor setting for a length of time maybe empty, meaning no coolant in it? But if you noticed rusty color, I would suspect your radiator is now full of rusty scale from the engine, and the flow is impeded hence the boil over... I would take it to a shop and have it boiled out. Flush out the motor without the heater or radiator hooked up other wise you'll flush all the loose crap back into it.

I dont think this will help the gas mileage though LOL

The motor had been recently built (2012ish) and was in a running cj7 when I got it. I had it swapped over (2012) but dont know much more than that. The radiator I removed today did have rust in it but the antifreeze was nice and green still as it was just filled a hundred miles or so ago. It was just that top hose that had rust in it, I assumed from that spring in it.
 
thanks Ghostwave for the very informative post above. Some mod might want to sticky just this tech info.

Diving deeper into what I have, it is a 360/999 auto/300. I have a basically new copper 3 row radiotor and OEM V8 CJ fan shroud. I already have an external tranny cooler that was mounted to the old radiator. Currently I have 34x10.5x15 tires with stock axelsand gearing. Axels and gearing are later on down the road.

Based on what you have typed above, I should be in a better place now, correct?

I'll try not to have an expert opinion on a combination I have not personally tried. That said, it sounds like you have the right type of components lined up so if it does not at least drive down the road without overheating, I'd be surprised and be looking for some kind of failure. Don't forget a new cap and at least watch the flow in the radiator to form an opinion on whether the water pump is circulating. Does sound like you should be in a better place.
 
Back
Top