• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

How hard to fix?

Escondido

Scrambler Junkie
Lifetime Member
City
BOERNE
State
Tx
I can work under the hood but have never done any body work. Looking at a new project. Frame is pretty good. But I don't know how scared I should be of this. Without body work experience I don't know if this is manageable or scary. Any thoughts appreciated.

00M0M_hZYCnRoJ0Vw_600x450.jpg
 
How good do you want it to look? The easiest and cheapest way is to cover it up with some aluminum diamond plate. The hardest way would be to blast the entire tub to white metal (after you've removed it from the frame and every component).

If those holes don't go all the way through, a bondo job might be OK.
 
That would make me nervous just by the look of it. As mentioned above; how good do you want it to look (and with no body work skill... how deep are your pockets)?
 
Is that area behind the rear wheel well the only rust spot? How are the floor pans? Bed? Rockers? If that is the only area I say go for it! If the whole thing is riddled with rust then I'd pass.
 
What do you want the finish project to be (i.e., factory stock, rock crawler, or resto-mod)? What is the asking price? Is this the only rust spots?
 
Could you show me the brush guard, does that look like what I think it is?
As for the body work if it's your first try at it and that's all that's wrong it's not too hard. You would need to cut out the rot and then weld in new sheet metal. Go slow as to not heating it up too fast or the metal will warp.
 
As someone else who did not know anything about body work heading into a project looking similar to that, I would say pass. The hardest part of my whole project, with an engine and transmission swap, by far the most time consuming, toughest part of the whole thing was patching, bond, sanding, painting and the like (and I even paid for some of the body work to be done).
 
That thing looks darn straight and the rear rust doesn't scare me at all. If the frame is indeed rust free then I'm betting the body rust is minor UNLESS it's been sitting outside collecting rain and leaves. Even then the bed should be the only major issue. If you're patient the bodywork on these is not that challenging and if you really want a Scram this looks like a very decent start. Post some more pics and let's see what ya got!

If it were me and I wanted a driver and the bed floor was shot I would have someone fabricate an insert and then cover it up with rubber. Honestly though I'm betting it's not that bad. I'd go for it.....
 
Ill agree with Dave K and also say that is what appears to be very localized rust. In other words way above average condition to start with. We would love to see more pics but based on just that one don't be afraid to dive in, given price consideration too of course
 
I'd be worried more about what you don't see yet if conditions for that Jeep were such that this rust could proceed this far.

If I were trying to make a really nice Jeep out of it, I'd be too paranoid for anything short of pulling the body and blasting it to bare metal.

Still a ton better than most, not saying it's not a great start, just that once I see rust through like that, I'd assume you're into frame-off/sandblasting land.
 
I haven't seen in person, trying to get up there later in the week. Had a buddy do the drive by. The owner also mentioned a rusting spot on the passenger side under the dash which had me worried. I'm not looking for showroom. Just something that drives well, hasn't be overly modded, and can be a nice long-term scrambler. Definitely not a 2 foot paint job. I think if the rear quarter is the worst the price might be ok. He's asking 7000. I seem to find plenty of 81 base models but not a laredo.

Here's the link to the jeep for sale. http://austin.craigslist.org/cto/4418968945.html
Couple more images from the ad. Somebody was asking about the grill guard.


00c0c_dQji1WgUC2M_600x450.jpg

01616_3TffO3n2sqM_600x450.jpg

00V0V_6FvmCvLdBrL_600x450.jpg



I
 
My eyes my eyesssss. Dam that front bumper has got to go.
As for rust if it was under a pine tree you would be surprised how fast the acid will eat the bed right along where it shows right now. I would inspect the body mounts and spring mounts for rot hopefully it was just pine needles in the bed. But I see rust above the rock guard on the passenger side and on the drivers side of the hood and windshield frame, I believe he's asking too much. Too much work for a beginner at body work.
 
That's a surprisingly reasonable price for a non-tricked out Texas Scrambler. I agree with KC, though, perhaps a bit high. You'll be hunting for replacement $eat covers, the body work, new front bumper and original chrome rims (if all that's your thing), but its otherwise a very nice mostly original Scram.

It is an 82, you saw that, right? The spare tire mount gives that away, but it is a Copper Brown Metallic which is a bonus :)
 
A Texas Scrambler Laredo WITH FACTORY AIR.....Very minimal rust....runs and drives well...Run, don't walk, to get it.

$7K for what appears to be an original paint Laredo with factory AC seems like an exceptional deal to me. The rust looks like it is from the seem joint where the bed is welded to the quarter panel. There is no paint under there so they are prone to rust under certain circumstances. Not to difficult of a repair as the "A" and "B" pillars seem to look good.

Just my :two cents: :wave:
 
Get pictures of the inside below the door, the support pillar behind the jeep emblem, along the floor where it meets the side. I may be wrong (trying to get look at pictures) but I'm guessing I see rust in these areas. If you see it on the outside, the odds are it came from where the metal joins together on the inside. If you get it, see if you can talk him down, I've seen better for 7,000 listed on this forum. If these areas are that rusted, you've got some serious work replacing metal for a 7,000 jeep when for 2,000 or so more you can get a real rust free or minor surface rust jeep. You would be money ahead.
 
I did see that it was an '82. I was just saying that I seem to come across plenty of base 81 models and have been hoping to find something with better options.

So far still available. I hope to get up there in the next couple days to look it over. Another nice one popped up in Houston. Will post it in third party sales.
 
Back
Top