• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

POS vapor lock?

trust

PITA
City
White Rock
State
NM
In March I swapped on a 4.0 head and mopar EFI, everything seemed fine, drove it to jeep safari and home and did have very slight vapor lock type problem coming home. I rerouted the fuel lines per the instructions and havent had an issue since other than on again off again pinging on regular gas although I also havent taken it more that 10 or 15 miles from home either.

I left last night on a much anticipated Big Adventure with two long time 4 wheeling buddies, we have done a week long BA for several years now and they are one of the highlights of the year. We missed last year because one of the guys was working overseas so this was also a homecoming/reunion of sorts. You can tell where this is going....

Left last night with a full tank of premium (to address any pinging issues), all my camping gear, ARB Fridge, etc. Actually well packed and stowed. The pinging was persistent although off and on and mostly related to incline, up hill ping, down hill not. This is the flat part of the trip. Temp about 1/3 up the gauge, tranny temp about 120, everything in the green. About 730 pm, after 48.3 miles by GPS it starts to cough and sputter and quits. Pull to the side, get out and start looking, fuel line to the rail is cool to the touch, fuel line at the junction between new and old is cool, pressure regulator is warm but comfortable to touch as is the fuel pump.

15-20 min and it's running fine, 6 miles and sputter then die.... again everything is cool, I dont hear fuel boiling like I have in carbed engines. 20 minutes and when I go to start I notice temp gauge is now 3/4 scale but it fires up, temp comes back down to 1/3 and off I go, about a mile and sputter. Long story short it's now 830 or so and i abort and after a rest i turn around and head home. makes about 55 of the 60 miles home without issue and going up the last significant hill (actually, the only really noticable hill in the whole 120 mile failure) it really struggles, sputters and dies. Finally restarts, limps up the hill and runs back into town and parks at the house...

So, two things, 1) why does it continue to ping? I have changed out the plugs, actually already had and didnt realize it, to the cooler, guaranteed not to ping spark plugs and am running premium 91 octane fuel. Timing is computer controlled and I cannot manually retard it. 2) why is it vapor locking, or is it? I did check all clamps/connections and the system is tight, no air leak to cavitate the pump. I did not have my fuel pressure gauge with me, I loaned it out and havent seen it but will this weekend although who knows if i can duplicate the problem or not. I do have a spare pump and probably should have changed it and the filter but didnt. I find that hard to accept though as this POS has been my daily driver for 4 months or so without issue and a weak pump would have been an issue when it was 110* here, not 50* wouldnt it? Could the 4.0 head be cracked? The power and mileage from this swap have been, to say the least, underwhelming. I would swap the stock head and carb back on but I sold all those parts last Friday since the swap seemed to be at least working if not spectacular

Thoughts, suggestions? I will be spending time with the MOPAR people at SEMA next week (assuming the cummins doesnt fail on me too) but I expect that to be fruitless. My current 'plan' is to just sell it and move on to something less disappointing as a hobby. After 37 yearss + of jeeping I think I'm done with the damn things but I hate to move this thing in it's current condition. 24 hours ago I would have told prospective buyers they could drive it anywhere, now I wouldnt sell it unless the buyer brought a trailer
 
pump, filter and regulator are on the cross member in front of the tank per the MOPAR instructions, fuel line is the stock 3/8
 
I this system has the regulator at the tank with the pump, the return line is either 5/16 or 3/8, I believe it's the 5/16 line, which ever is in the directions. It was suggested that the pump might be marginal?
 
Last edited:
changed pump and filter, doesnt run at all now, in correctly, verified the polarity, etc clearly no fuel pressure in the rail but I need now to go to town and buy a new fp gauge
 
It's hard to figure out what is causing your vapor lock issue from this side of the keyboard. How close are the lines to the exhaust? Are the lines all running down the drivers side and have to cross over the exhaust? Take a pic of the filter/regulator and maybe we can figure it out.
 
return line is 5/16, pump, regualtor and filter are on the crossmember just i front of th etank per the directions. The supply runs down the passenger side frame rail, the exhaust down the drivers. When it did it the fuel line in the engine compartment was cool to the touch and there was no sound of percolation.

I got the pump and filter changed and the fuel line eventually refilled and purged enough for the pump to draw properly. Went about 90 miles and did the sam ething curiously, it did it at the same place it ALWAYS coughs, sputters, and dies, every time I've passed that spot for the last 8 years I've owned it, regardless carb, efi, whatever. VERY curious. Restarted after a bit and ran ok until an uphill stretch about 3 hrs later and did it again, it was snowing at the time and about 11 pm. Again, lines are cool to the touch, temp is 1/3 or less, trans temp is ~110 or so.

After that it didnt do it for the rest of the weekend until I was coming home today and did it after about 170 miles from the previous fill up, at about 3/8 tank. Filled it from jerry cans and it ran fine the 140 miles home. It does ping more or less constantly under load or up hill with 91 octane fuel (highest available) and even with premium and an octane booster. at least at highway speed in teh dirt it didnt seem to but I may have missed it. Instructions say it needs 93 Octane at sea level (why? the stock 4.0L doesnt?) Timing is controlled by the computer and I have done the cooler plug swap that is supposed to alleviate the ping (so is the head but it doesnt)

thanks for the help with this, it just ruins the purpose of the jeep

Hesco does say that it will ping unless you buy their special chip..... suffice it to say, not exactly th eresults I had expected from all of the myriad web info on the swap
 
Last edited:
So, am I understanding right.... that it runs fine when the tank is full (other than the ping)? And trouble starts at less than 1/2 tank on hills?

Have you looked inside the tank? Your intake tube, screen and pick up may need some attention. If it cracked part way up or some other wierd thing due to vibration or rust or whatever.... it could cause system to pull air, reduce fuel rail pressure, and ping due to lean condition or shut down because injectors cant work properly.
 
One other thing is to make sure the tank does not have any pressure or vacuum in the tank. Does the cap hiss at all when you open it up?
 
not exactly, it is likely to have trouble when it gets in the 1/4-3/8 tank range but that's not a given. When it did it last time and the tank was low there was pressure in the tank now that I think about it. And there is a small dent in the skid plate under the tanks, I plan to drop it and pound it back flat so that could be causing some fuel starvation at very low tank levels but it was near full when it did it initially.

It SEEMED to be better with the new pump, not perfect but better. It still pings even premium with additive and still had, at times, disappointing performance and at others tolerable.

Thanks for the suggestions
 
Next time open the cap when it vapor locks(or before the place where it normally has a problem) and see if it has either/or pressure or a vacuum in the tank. If the tank isn't venting well, the fuel volume consumption may exceed the tanks ability to deliver it.
 
Sorry to hear about your problems with the MPI:(

I installed the same kit on my red Scrambler (identical except I have the manual trans computer) and have had great luck with it so far, except for the 10-15 second slightly rough idle after initial flair on start up.

I ran my fuel feed line (5/16" line) and fuel return line (1/4" line) both down the drivers side, same side as my exhaust. I too was concerned about vapor lock, but so far I have had no issues. I drove mine non stop from coastal Mississippi to north Alabama a few weeks back, 70-75 mph, I had no issues. I even ran it completely out of gas, no problems:eek: It sputtered once, i knew it was about empty, so I slowed down some. Got in the right lane, slowed down to 55, kept driving smooth. It died, did not try to restart it, coasted on the blowout lane. Dumped 5 gallons in it, fired right back up. Drove it 1/8 of a mile to a gas station, took 7 gallons to fill it up. That's how I know the advertised 15 gallon tanks only hold 12 gallons. Anyway, my cap did not hiss when I removed it, so I am assuming my vent system is working correctly. I also ran a new metal vent line from the rear of the jeep to the under hood canister. Maybe double check how you ran your lines off of the charcoal canister, if I remember the instructions were not too clear on this part:shrug:

I am curious to see how you crossed over the engine compartment with your supply line. I did not like how the instructions wanted you to run the line down the passenger side, then cross over to the manifold under the hood. Seemed like a bigger risk of vapor lock running the line this way IMO. I ran my supply line down the driver side frame rail directly to the manifold, right along side the factory return line. My pump and filter are mounted on the cross member in front of the tank.

It seems like the newer MPI kits Hesco sells don't utilize a return line, Hesco says that they are less prone to vapor locking, but I don't know anything about this setup. I always thought you had to run a return line on a high pressure fuel injection set up? Seems like the two line system would be better against vapor lock, considering fuel is constantly flowing through the lines, not sitting stagnant inside the lines:confused:

As for the power increase and mileage gains, I am very happy. JeepAddict on this board drove my red Scrambler, and he too was impressed by the power. Several other local jeep people have drove it, and were also very impressed. My red Scrambler will blow the doors off of my stock 05 Rubicon, even though it is pushing 35" tires and the TJ is pushing stock height tires, both with 4.10 gears:drool: MPG at interstate speeds had been 16 mpg, which I think is good for 35" tires, 4.10 gears, no overdrive. A few people have been trying to get me to put a 4.0 head on my 258, but I am so happy with its performance I don't want to risk screwing it up. IMO, I don't see how a 4.0 head could improve what I already have, or if it would it would be such a minuscule gain it would not be worth the trouble/expense:confused:

I have been mainly running 93 octane premium with no pinging at all. I also ran 1/2 a tank of 87 octane through it, no pinging. I have been running 93, just to be safe though. I did run 91 in north AL with no issues, too.

What kind of camshaft and or compression ratio are you running? Is the lower end of the engine within spec:shrug:

Hopefully this issue can be resolved fairly easily:fingerscrossed:
 
A dent in the skidplate wont matter. That would only be an issue, maybe, if the skidplate and tank are touching at the dent and vibrate together which may make a hole eventually.

But, taking a hit hard enough to make a dent could affect your pick-up tube, vent lline, etc... I would check these first.

Vapor lock is almost never a problem on EFI vehicles because the fuel is under high pressure which increases its boiling point significantly. In the jeep system specifically, it constantly flows to the fuel rail and back to the tank so it doesnt sit in a hot spot in the line for too long and what isnt burned gets to go back and expand in the tank to cool off.
This cycle makes vapor, which can pressurize your tank, which can affect how well your fuel pump works. And as mentioned above, too low fuel pressure makes lean condition, makes ping.
 
Last edited:
In the jeep system specifically, it constantly flows to the fuel rail and back to the tank so it doesnt sit in a hot spot in the line for too long and what isnt burned gets to go back and expand in the tank to cool off.

Not all of the Jeep systems have a return off of the rail-
 
Next time open the cap when it vapor locks(or before the place where it normally has a problem) and see if it has either/or pressure or a vacuum in the tank. If the tank isn't venting well, the fuel volume consumption may exceed the tanks ability to deliver it.

I had this problem several years ago when I did the 4.0 conversion. The same solution as Mysunnshine's is what got me on the way to fixing my issue. The issue was related to eliminating what I believed to be unnecessary vacuum lines to the canister and turned out to be important for the vent line for the gas tank.

So were you able to complete the trip in the Commanche?

Later, Ken
 
not exactly, it is likely to have trouble when it gets in the 1/4-3/8 tank range but that's not a given. When it did it last time and the tank was low there was pressure in the tank now that I think about it.



Thanks for the suggestions

I had intended to post earlier, however since I am not familiar with the MPI conversion, I decided to leave it to the ones that are.
I know from past experience with a carb/mechanical FP system that the vapor lock like problems can be caused by the return line to the tank being restricted or blocked.
On my buddies 8 I found this to be the case and the problems would show up after extended running time. The fuller the tank, the sooner the problem. His was getting a vacuum in the tank that would eventually cause fuel starvation. Once I decided that may be the problem, an easy test was to loosen the gas cap. The problem went away. Upon checking the return line it was discovered to be obstructed by 25+ years of rust build up.
Someone else on here had posted similar symptoms with a carb system, I never did hear back on what he found.
HTH. Good luck with getting the conversion straightened out. I'm still hoping to do a head/MPI swap from my GC someday.
 
Back
Top