• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Roll Cage Pics and Opinions

TXtrailbuggy

It sure is smokey in here
City
Kyle
State
TX
I am looking to design a roll cage for my 8. I would like to see pics of those who have cages, half and full.

Also I was wondering what everyones opinion is with this; do I tie the roll cage into the frame or do I design a cage that is a completely self contained pod type and just bolt it to the body, with reinforcements of course.

Thanks, Bo
 
this is my winter project this year...i too look forward to the posts..i finished building my tube bender..just waiting on cold weather before i start
 
I like mine in the Unlimited and I will be copying that for one of the Scramblers.

101_0044-1.jpg


I love the Shape from the top.

101_0040-1.jpg


101_0825-1.jpg


101_0827-1.jpg


101_0826-1.jpg
 
Last edited:
Here's a few of mine . . not too good in detail though. I'll try to get more.

A031-1.jpg


It was made so that the spare could fit vertically in the back of the Jeep. It was like that when I bought it. There are a few things I would have done differently, but in the end, it's a cage, I need a cage, it is very well made and will do the job:

100_0700-1.jpg


100_0050-1.jpg
 
I'm in the same boat - designing a cage for the 8. My Scrambler (if I ever finish it) is not going to be hardcore by any means - all new sheet metal, fresh paint, new interior, etc. The goal is light wheeling, family camping and yeah, I'll admit it - just cruising around on the pavement in a classis 8... So, I don't want a jungle-gym of tubes. I want a stock-ish look... as stock as full cage can look anyway.

The challenge is putting the C and D pillars in the "right" places. I want 3-point belts for the rear passengers - just factory-style shoulder belts. So, that means an upright near the back seat. But it has to be behind the rear seat.

And I don't want a tube (like a diagonal) passing the rear passengers’ heads – side impact or roll will cause one’s head to smack the bar = death… Our heads don’t do so well with hard side loads ;)

I had hoped to have only the A (windshield) pillar, B (behind front seats) pillar and a D pillar – just behind the rear seat… but if I push the rear seat back (for more leg room) the space between the B and C pillars is too great – needs triangulation… hmmm
 
Last edited:
Here is my setup. I've gone the expensive route before, check out www.roverhybrids.com an look under the projects link. That was a custom made full cage. My current Scrambler utilizes the stock roll bar in the bed but, I bought a full CJ-7 cage and cut it up to fit under my 1/2 cab. It was a cheap route to go this time and I like it just fine.....
 
Here is what I did, EOR font cage for a scrambler, and I took a second rear factory bar and I cut it up to make a full cage. Where the factory hoop bends inward I cut and rotated it so it bends back and lines up with the rear feet. So the rear hoop is welded to the original roll bar at the foot and so the floor mounts are original. I do not do rock crawling here in FL, and this also allowed easy entry as well as use of my half cab.
DSCF3472MediumJPG-1.jpg


I also took the EOR dash bar and I used that to fabricate a frame tie in. Got some polyeurethane bushing from a auto store to cushion them. I think they are from a torsion control system or something. I just need to paint the frame tie in. I only tied in the front part of the front cage since the floor board is not that strong, the rest mounts to more substantial body areas.

DSCF3473MediumJPG-1.jpg
 
Last edited:
Stouttrout said:
I like mine in the Unlimited and I will be copying that for one of the Scramblers.

101_0044-1.jpg


I love the Shape from the top.

101_0040-1.jpg


101_0825-1.jpg


101_0827-1.jpg


101_0826-1.jpg

Why am I not seeing all your rigs in magazines? You do some of the nicest builds I've ever seen....:bow:

.
 
WildTurkeycj8 said:
Why am I not seeing all your rigs in magazines? You do some of the nicest builds I've ever seen....:bow: .

Not only does he build 'em well, our man Dan know how to wheel that thing!:smokin:
 
I'm sure you've seen my old Scrambler around before, but I loved this cage. I had an inside cage made (so I could get the half hard top on) and a rear cage in case I ever wanted a back seat. All tied into the frame

JeepBoat1small1-1.jpg

back shot
Photo274-1.jpg
 
Last edited:
cjgoode said:
Here is what I did, EOR font cage for a scrambler, and I took a second rear factory bar and I cut it up to make a full cage. Where the factory hoop bends inward I cut and rotated it so it bends back and lines up with the rear feet. So the rear hoop is welded to the original roll bar at the foot and so the floor mounts are original. I do not do rock crawling here in FL, and this also allowed easy entry as well as use of my half cab.
DSCF3472MediumJPG-1.jpg


I also took the EOR dash bar and I used that to fabricate a frame tie in. Got some polyeurethane bushing from a auto store to cushion them. I think they are from a torsion control system or something. I just need to paint the frame tie in. I only tied in the front part of the front cage since the floor board is not that strong, the rest mounts to more substantial body areas.

DSCF3473MediumJPG-1.jpg
What make are your rear fender flares ? Pat
 
to pcozad1 not trying to be a dick but how your cage is tyed to the frame i wouldnt trust the bolts at that length "your only as strong as your weakest point " the cage is strong but if you roll and those long bolts break now you have no cage only reason i say this is i come from desert prerunning and speed really tears things apart
 
Here's a few of mine . . not too good in detail though. I'll try to get more.

A031-1.jpg


It was made so that the spare could fit vertically in the back of the Jeep. It was like that when I bought it. There are a few things I would have done differently, but in the end, it's a cage, I need a cage, it is very well made and will do the job:

100_0700-1.jpg


100_0050-1.jpg

this thing looks even better now that it is in my rig!!!
 
to pcozad1 not trying to be a dick but how your cage is tyed to the frame i wouldnt trust the bolts at that length "your only as strong as your weakest point " the cage is strong but if you roll and those long bolts break now you have no cage only reason i say this is i come from desert prerunning and speed really tears things apart

That was actually cjgoode's rig. pcozad1 was just quoting it to ask a question.

And holy old thread Batman! I miss Hazard's rig... always liked that one.
 
Back
Top