• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Shocks and Body Roll

FlagJeep

Scrambler Junkie
Lifetime Member
City
Flagstaff
State
az
So over the years I have proven not to be brave enough to drive over 55mph in my Scrambler due to side to side body roll that kicks in and gets worse with more speed in that region.

I currently have a Rubicon Express 4.5" lift with Rubicon Express monotube shocks, and 35" tires. Some input I have gotten is that better shocks will take care of this issue (the steering seems fine as far as I can tell). I have a sway bar that I am going to improve the mounting brackets on as well.

Any input? I kind of figured way back when building the scrambler that the RE shocks would be the best match with the RE lift but didn't do any real research. I am attempting to get into contact with some companies to figure out a good match of a shock set-up. It would be nice to get to 75mph comfortably, so I could drive the freeway and not get my doors blown off, but have just mostly avoided it to date due to my own speed limitation.

Any thoughts are appreciated
 
I have the RE 4.5 kit, no sway bars, and Edelbrock shocks. I have had it over 100mph several times, and it cruises comfortably at 80 MPH. But- I also installed all new steering components, new ball joints, and made sure there was NO play when putting it all together. My tires are 35", and the wheels are 8" with .25" negative offset. I have found that loose steering, wheels with a lot of negative offset, and loose spring mounts all contribute to vague steering. I can dry turn my Scrambler and get no pops, no clicks, and corresponding equal rise/fall due to proper caster.
 
Yeah, mine is not steady enough for 100mph.

I replaced and upgraded the ball joints when I built it, replaced the steering box. It turns pretty steady and quiet until it stops.

I'll try to get the front end in the air this weekend and see if everything feels tight

Spring mounts are tight

What is the rise and fall with the caster that you are speaking of?
 
When I built my scrambler I set my caster to 8 degrees to make the steering a bit lazy. The Jeep drives perfectly smooth and straight at any speed and I can even take my hands off the wheel at 75 with no issues. I have a 3 inch black diamond lift with Bilstein shocks and a sway bar running 33x12.50 BFG all terrains.
 
Don't let shocks control your body roll. Let a sway bar do that.......

I'd be glad to, except it doesn't seem to help. I'll have to look closer at things I guess, gonna try to clear some garage space so I can get to work on it.
 
Take some pics of your front end/axle at ride height and the sway bar components. I'm guessing that you have something going on because I can run 80 all day long without issue. And like what Kane said, caster can contribute to some of the driveability with twitchyness. Does it change(get better) when you have the hard top off?
 
Hope this shows something

Take some pics of your front end/axle at ride height and the sway bar components. I'm guessing that you have something going on because I can run 80 all day long without issue. And like what Kane said, caster can contribute to some of the driveability with twitchyness. Does it change(get better) when you have the hard top off?

I haven't gotten it to go over 60 with comfort since I assembled it. I do need to repair a passenger side sway bar bracket, but the issues were present well before I screwed that up (had forgotten to reconnect the sway bar disconnect once). When the hard top is off, it is different but I don't think it goes away. I don't know that I have pushed it when I have had the top off.

It is sunny out, which lights up some of the pics and washes out some of the others. Let me know if you notice something, need a better picture of a specific spot or if my pictures generally are all at unuseful angles. Thanks for the input.

I know I need to re-spool my winch too
 

Attachments

  • front view.jpg
    front view.jpg
    49.5 KB · Views: 94
  • under from front.jpg
    under from front.jpg
    61.2 KB · Views: 95
  • under from rear.jpg
    under from rear.jpg
    58.1 KB · Views: 94
  • damaged sway bar mount.jpg
    damaged sway bar mount.jpg
    37.1 KB · Views: 94
  • driver wheel.jpg
    driver wheel.jpg
    44.7 KB · Views: 94
  • passenger wheel.jpg
    passenger wheel.jpg
    35.1 KB · Views: 95
  • passenger shackle.jpg
    passenger shackle.jpg
    43.7 KB · Views: 94
  • driver side axle view.jpg
    driver side axle view.jpg
    43.4 KB · Views: 94
Take some pics of your front end/axle at ride height and the sway bar components. I'm guessing that you have something going on because I can run 80 all day long without issue. And like what Kane said, caster can contribute to some of the driveability with twitchyness. Does it change(get better) when you have the hard top off?

I have a friend up here who's scrambler had a similar feel and he said he had to put a shim in between the leaf spring mount on the rear frame and that took most of the roll away. It has seemed to me that it feels like a lot of the roll comes from the rear, but I could just not be aware of what is actually happening.

I don't have a fancy rear sway setup like the mysunnshine Scrambler
 
I don't have a fancy rear sway setup like the mysunnshine Scrambler

LOL.....I can tell you where to get one.. ;) It does make a difference.

You're still running the stock steering shaft? How tight is it? Ususally the pucks in that bell tend to wear out. Borgeson makes a nice replacement....
 
Cell phone pics are terrible for this. The fish-eye effect is generally corrected electronically... but not so much with front-end photos!

I've even run outside to look at my own Jeep, after seeing close-up photos that look so out of whack! :crazy:

That said, toe-in is a good thing to check, as is caster. Mine doesn't wander, but it doesn't exactly self-correct, either. It's not unmanageable, even at 65-70mph, but I've got to pay attention!

I really should get an alignment check, just so I know what's going on....
 
The rise/fall I was speaking of is due to the caster.
 
Cell phone pics are terrible for this. The fish-eye effect is generally corrected electronically... but not so much with front-end photos!

I've even run outside to look at my own Jeep, after seeing close-up photos that look so out of whack! :crazy:

That said, toe-in is a good thing to check, as is caster. Mine doesn't wander, but it doesn't exactly self-correct, either. It's not unmanageable, even at 65-70mph, but I've got to pay attention!

I really should get an alignment check, just so I know what's going on....

Yeah, I need to double check it, and make sure it didn't have to do with camera or how it was parked. Moved it into my garage, can re-check tonight
 
LOL.....I can tell you where to get one.. ;) It does make a difference.

You're still running the stock steering shaft? How tight is it? Ususally the pucks in that bell tend to wear out. Borgeson makes a nice replacement....

Still have the stock steering shaft, how would I gauge "tightness" in it?

I'll take one of those custom rear sway bar set-ups you have, I am sure they must be affordable right? :D
 
One thing I had to do on my RE kit was replace the bushings on the frame end of the front shackles. The "conversion" shackles they use put a lot of force on those bushings and they developed a lot of play over time.

I'd also like to get clarification about this "side to side body roll" at speed. Is the Jeep not tracking straight when you're trying to drive straight at higher speed and that is inducing the body roll or is it that the Jeep tracks ok but when you're turning at speed you lean or sway uncomfortably? Pretty important difference in those two scenarios, to my thinking.

As has been said, there's no reason a lifted Jeep can't drive perfectly well at any highway speed.
 
One thing I had to do on my RE kit was replace the bushings on the frame end of the front shackles. The "conversion" shackles they use put a lot of force on those bushings and they developed a lot of play over time.

I'd also like to get clarification about this "side to side body roll" at speed. Is the Jeep not tracking straight when you're trying to drive straight at higher speed and that is inducing the body roll or is it that the Jeep tracks ok but when you're turning at speed you lean or sway uncomfortably? Pretty important difference in those two scenarios, to my thinking.

As has been said, there's no reason a lifted Jeep can't drive perfectly well at any highway speed.

I'll check the shackles.

When driving down the road it will track straight, then the side to side movement of the body makes driving sketchy proposition, with the steering eventually impacted seemingly by the momentum of everything above it going side to side. Trying to correct it with steering will typically magnify the waviness, so I have to slow down to regain steadiness

Sometimes it seems wind induced (especially with the hard top on), it can be induced by steering, I have almost felt like accelerating can cause it perhaps from unequal push from one wheel versus the other out of the rear axle (might be making that up but it feels that way sometimes), and in general if I am going fast it will get wavy.

A fast corner is something I expect to be uncomfortable, so that really isn't the issue, although I could make it one if I tried it.

Thanks for the input, hopefully this weekend I can dig into the Scrambler and figure some things out. All input is appreciated.
 
Ah....

Is there any reason for those swaybar drop brackets? They aren't part of the RE kit, were they on there with a previous lift?

Your swaybar links are longer to make up for the lift, so they're leaning well back because of those drop brackets. Stands to reason that your swaybar links are rotating between the pivot points rather than actually actuating the swaybar properly. Hold a pencil between both hands with the pencil vertical. When you move the lower hand up, it's going to push the top hand up. Now put the pencil at an angle like you have on your links and push the lower hand up, the pencil is just going to want to rotate in space.

This effect is enhanced because the links are leaning rearward. The axle is going to move forward as the suspension compresses, moving that end of the link forward as it comes up. I think you're basically driving it as if there's no swaybar at all.

I'd put the swaybar back in the stock location, and get some new polyurethane bushings to swap in at the same time while you're at it and see what that gets you.
 
Back
Top