• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

SOA Kit

It looks well thought out, but doesn't look "Heavy Duty" in the pics on their site.
I'm curious how much it all adds up to with all the bells and whistles.

More specifically:

SOA spring plates/U-bolts
Rear Anti-wrap bar
High steer setup
Extended drive lines or dropped T-case adapters
lengthened brake lines
longer shocks

I think thats about all you'll need :D
 
What's your opinion on a SOA lift in general? I am running 35's right now and would like to get a little more clearance (around 6" to 6.5"). Currently I have a Rubicon Express 4.5" spring lift. To get more clearance I know the only option with the RE is a body lift of about 2". I'm not really crazy about body lifts, so I was thinking about doing away with the rubicon springs and replacing them with stock YJ springs and doing a SOA (which would give me about 6.5"). Any advice on if this would be the way to go? I know that a body lift would be cheaper, but overall for a better ride and better offroading I've heard that a SOA is the way to go.
 
My opinion on SOA is if you can run whatcha got with minor mods STICK WITH IT. SOA is great off road but it has drawbacks on road. That lift you have is a fine setup and will take you far if you just need a little clearance trim.
Only trim what you need, that will give you the clearance you're looking for AND keep your center of gravity low.

When are you having problems with rubbing? Where are your tires touching the body?

If you want to drive your rig onroad stay SUA, if you like to work on your rig and run heavy trails SOA is a great choice but for all around safety and low maintenance performance keep the Spring Under setup you have now.
 
I have yet to figure out why a dropped pitman arm doesn't work for steering for anybody that learns stuff on the internet. I really don't like the Z drag like either.

Stock YJ springs are too soft. Get lots of body roll and axle wrap.

The best options I've done are CJ rears with extra leafs added, and toyota fronts with extra leafs added. The toyota fronts are mil-wrapped. You need to use stiffer than stock to still have good highway manners and minimize axle wrap. Don't worry about the flex, it will.

Since you already have a good lift I'd just stay with it. Install some TJ flares.
 
ryankopecki said:
I have yet to figure out why a dropped pitman arm doesn't work for steering for anybody that learns stuff on the internet. I really don't like the Z drag like either..

A dropped pitman arm wont work because the leaf spring gets in the way of a straight drag link - hence the (IMHO, poor) "Z" solution given here. Hi-steer is really the only way to go on an SOA set-up. When one usually considers how "cheap" an SOA is - they usually don't consider the steering issues. To do it right, with hi-steer, is not cheap.

ryankopecki said:
Stock YJ springs are too soft. Get lots of body roll and axle wrap.

I agree... I even added extra leafs to a set of stock YJ springs - they "almost" lasted one complete season of wheeling - then, they were shot. I now run the RE SOA 1.5" lift springs and am quite pleased with them.

Also, as far as this "bolt-on" SOA kit goes - it looks like it positions the new, over the axle, perches parallel to the old, under the axle perches. While this is great for the front - it will not work for the rear. More than likely you will want to go with a CV drive-shaft (another "cost" of SOA usually overlooked) in the rear which requires a new pinion angle on the rear axle.... and, I'd hate to add shims to that stack of bracketry that would be there already.
 
Last edited:
Rocktracktor hit the nail on the head. SOA is good when done right. That kit is a great starting point but by the time you're really "done" it's going to be over $1500. easy.

Run whatcha got.
 
Dropped arm worked for mine back in the day. Seems it works on all the ones I see on the trail. Lots of YJs run that way also. Have to stay low though. No 1.5" lift springs and no longer shackels. Not saying it will never rub at full lock right with right front at max droop.

I agree with you on the shims for the rear. I think most people waste money on a CV shaft to fix a problem that could have been solved with shims. I prefer to actually cut the perches off and reweld them so there are no shims to crack and fall out. Most SUA lifts I've checked set the angle wrong also. Drivetrain height and angle (flat skids) can also have a big effect on whether a CV shaft is needed.
 
Last edited:
I have used their SOA kit, OTT steering kit, YJ spring conversion kit, springs and shocks. Biggest problem is their service is terrible. The kit didn't arrive complete and it took forever and was a considerable hassle to finally get the parts that had already been paid for. Their steering kit is a good idea but toe in adjustability is poor. The YJ conversion has since been replaced with a MORE reverse shackle kit. The YJ springs are too soft on the street and I will never purchase anything from RRO again and would advise you do the same. If you are going to do SOA it is a lot more involved than just finding a way to put the axles under the springs. I don't believe there is one particular kit that's going to have all the answers. The dropped pitman arm and steering problems with SOA are real and not simple to fix. Good shocks and springs are a must. SOA is problematic on the road. It can be done but is a compromise at best for on and off road. You may already have a better starting point for where you want to end up.
Good luck.
 
Thanks for all the advice, I think I will steer clear of RR Offroad and the SOA. I will be using my jeep for more of a daily driver than offroading, so I definitely want to keep the on road driving at its best...
 
I just want to know why you're having clearance problems with the current setup.

Maybe a mild body lift or trimming is the way to go.
 
I have the same problem. I am running the exact same tire/rim set up with a Superlift 4" lift and was trying to decide on what to do about a little more clearance. I am strongly considering triming and installing TJ flare. Post your decision when you make it.
 
I ran the Superlift 4" kit...more like a 3" kit. My new RE Extreme 4.5 looks like it will clear 36" tires with no problems....
 
The 35's will fit with the rubicon 4.5", but just looks like they are crammed in there. Would look better with about 2" more clearance. Will probably end up with a 2" body lift, still unsure.
 
Back
Top