• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Spankrjs 1985 Spring Special CJ-7

Took some of the top parts off the carburetor so I could remove and clean the idle tubes.

Reference picture for me:

20261103_175306.jpg

Took this top plate off to take a look, everything moving freely, no debris in here, looks OK.

20261103_180308.jpg

Take these parts off:

20261103_180323.jpg

Then you can get to the idle tubes.

20261103_180314.jpg

Two screws and the entire venturi cluster comes out.

20261103_180334.jpg

NOTE: I also removed and reinstalled the little check ball to blast out a few more ports with carburetor cleaner. Be careful with this, very easy to drop it down into the intake/engine!!

Using torch tip cleaning kit to check/clean the idle tubes for obstructions.

20261103_182123.jpg

Blast carburetor cleaner through the tiny port inside the big circle. One for each tube. This is how fuel gets inside the brass tubes.

20261103_182142.jpg

Blasted out all the little ports in this part with carburetor cleaner, too.

20261103_182156.jpg

20261103_182206.jpg

Make sure to reinstall the little check ball before reinstalling the removed parts. Be careful!!

20261103_182930.jpg

Then reassembly.
 
  • Like
Reactions: SKT
Good news/bad news: no real gunk or varnish observed, no blocked idle tubes or ports that jumped out at me.

20261103_184639.jpg

Restart took a bit of effort, all the fuel and carburetor cleaner flooded the engine when I was screwing around. Finally started up, idled like crap for a bit, finally cleared up. Quick test drive, maybe marginal improvement.

Little bit more screwing around, unplugged the vacuum advance, engine did not immediately drop RPM which I thought was odd? After a few seconds RPM would drop. Vacuum advance hose definitely pulling. Plugged that hose back up, unplugged the 4"/10" vacuum switch and drove around. Not a good idea, you have to really baby the throttle to keep the engine from falling flat on its face. So, just assuming that thingy is doing what it is supposed to. Plugged it back in, another quick drive, a bit better. Drove some more, sometimes almost no issues, then they would come back. Very intermittent.

I improved the situation or it improved itself, at least it is not violently bucking/surging during light throttle anymore, but the stumble is still there.

Sprayed brake parts cleaner around carburetor and intake, no vacuum leaks were found. Maybe a vacuum hose leak somewhere?

Things Jeep does perfect:

Starts right up
Shuts right off (no run on or dieseling)
Idles perfect
Choke working properly
Sol-Vac working perfectly
High speed operation perfectly
Heavy and light acceleration perfect

Things Jeep does not do well:

Steady light throttle to maintain constant speed, slight surge or buck. Better but still present. From 5 -40ish miles per hour.

The same buck/surge is also felt while decelerating, either with foot 100% off pedal or normal slow lifting of foot off pedal to slow down with vehicle in gear.

Did not notice a "light show" from spark plug wires with hood up/engine running outside in the dark.

So, maybe a carburetor blockage that is slowly working it's way out?

Maybe a slight vacuum leak leaning out mixture?

Maybe idle mixture set a hair too lean (was not a problem 6 years ago).

Maybe timing off (was not a problem 6 years ago)

Maybe vacuum/mechanical advance not working properly in the distributor, maybe sticking? Did have this issue 6 years ago.

More work/diagnosis needed, that's it for now.

20261103_193059.jpg
 
Piddled with this one some Saturday morning.

20261107_073353.jpg

Decided to investigate the distributor/timing.

20261107_073407.jpg

Distributor installed, twisting the rotor, it would spring back but the weights were not swinging back consistently each time, at least the one I was looking at through the square hole in the pick up base plate. That might be normal, not sure.

20261106_184826.jpg

20261106_184828.jpg

20261106_184834.jpg

So, decided to investigate. Pulled the center gear thing off (don't lose the roll pin), then the pick up coil. First thing I noticed, one of my springs is loose, providing no "spring" back at all.

Loose spring:

20261107_074736.jpg

Tight spring:

20261107_074722.jpg

I kept both the original springs I removed from the distributor with these two aftermarket light springs.:

20261107_075214.jpg

20261107_075239.jpg

Comparison, left to right:

Too loose original spring
Spring I had installed, too loose
OEM spring I reinstalled

20261107_075324.jpg

Unfortunately, no real data on what springs are used in what OEM application. Only way to verify is to map the Advance curves, which I did before, probably need to do again. I imagine some tension at rest is better then none. With none, getting some mechanical advance at idle, besides the initial advance you set.
 
Spring installed, note dry oil wick/sponge in top of distributor shaft.

20261107_075720.jpg

A little drop of oil added. I imagine this dried out due to the Jeep sitting up a long time. A little dab will do you.

20261107_075856.jpg

Put a little plastic safe oil (rc car crossover product) to the plastic bushings on the Advance weights.

20261107_080249.jpg

Took apart the Advance plate to add a little lube here, too.

20261107_080340.jpg

A little dab on the three yellow dots and on the center raised metal portion.

20261107_080425.jpg

None of these parts were sticking on the bench, but a little lube won't hurt.

Reinstalled everything, don't lose the little PIA roll pin!

20261107_081510.jpg

It is easier to slide gear down the shaft, then install the roll pin.

20261107_082026.jpg

Quick test drive, a bit better, but still have the surge when transitioning from idle to low speeds. Better, but still annoyingly there. The whole engine/Jeep is not bucking anymore, bit still not right.

So, hard to know if anything I have done has improved anything, or maybe I still have a carburetor blockage that is working itself out.
 
Checked the timing, some information. Just remember, this Jeep is still using the MCU to control timing, so not like a regular carburetor/timing set up.

Everything hooked up, engine running at idle speed of around 600 RPM, only 8 degrees advance showing.

Unhooked vacuum advance and vacuum switch, total timing at idle of 600rpm is 6 degrees. So MCU only allowing 2 degrees of advance at idle?

So, looking at my underwood sticker, checked the timing at 1,600rpm, around 20 degrees total (this is with switch unplugged and no vacuum advance).

20261108_184701.jpg

Should be 11 max, I was around 20 degrees.

Adjusted down, idle drops to 400 rpm.

Shut engine down, hooked up vacuum advance and vacuum switch, restart, base idle at 500rpm with 6 degrees advance showing.

I just added a bit more advance, so probably back where I started. Quick drive, a bit better. So, Shut Jeep down, came back took it on a 10 kile trip, it was crap. Not bucking, but terrible low speed operation. If you.are barely on gas it surges. If you give it more pedal it is fine. Drove it to my buddies house, it stayed parked about 8 hours. Drove it home, much better, but still present.

Very inconsistent. Wondering if I just have a carburetor blockage that is working it self out. I'll work on it some more next week when I get back from Hot Springs.

That's it for now.
 
Rev engine way up and at the same time have Jeepaddict slap his hand over the top of the carb. It works 100% of the time about 2% of the time.
 
Piddled some more with this one off and on this week at night after work.

Swapped out the ignition control module, just for the hell of it. This Jeep had been running a NAPA top of the line module. Swapped in a budget O'Reilly module I had been running in my green Scrambler over 10 years ago, before swapping that one to Mopar fuel injection. No change, problem still existed after swap.

20261117_182026.jpg

A note on modules, including the above picture.

20261117_182015.jpg

20261117_182009.jpg

Almost any new module you buy today is made in China. Best bet is to find a NOS Ford Motorcraft module. Interesting note on the above modules: the expensive NAPA and the cheap O'Reilly module are the exact same part. Same case, wires, everything. Only difference is the sticker, and the warranty. IIRC, expensive NAPA module has a 3 year warranty, budget O'Reilly module is lifetime warranty. So, buyer beware.

Anyway, ignition control module seems to be OK.

I also checked the ignition coil, both hot and cold, it checked out fine.

About the only bone headed thing I did recently to this Jeep had to do with the "Deceleration Valve". This is an emissions part, usually only found on California emissions manual transmission models. This part goes between the upstream pulse air tube/manifold vacuum source/big vacuum port on back/bottom of carburetor. Something to do when you dump off gas pedal, manifold vacuum soars, does something. Anyway, it needs to be mounted in the correct orientation, metal end up. There is some type of spring loaded diaprahm in there, can give you a very hard to find vacuum leak. I mounted it upside down when I installed the new valve cover gasket, not a good idea.

The Deceleration Valve, mounted in the correct orientation:

20261120_171815.jpg

Close up of the metal top of the valve:

20261120_171836.jpg

Reinstalled correctly, no change.

So, at this point I was about to start blaming everything under the sun: EGR Valve, coolant sensor, vacuum switch, carburetor.

I noticed tonight that it is more of a miss, not a flat spot. It got worse tonight when I was messing with it, consistent miss no matter what. So, being a redneck, I start pulling spark plug wires off plugs with the engine running to see if I could find a dead cylinder.

I pulled #1 off, noticed a difference, put it back on.
Pulled both #2 and #3 off at the same time, no change, got worried, maybe head gasket issue.
Pulled #3 and #4 off, very minor change.
#5 minor change, #6 big change.

So, let's pull spark plugs. All plug wires are firing. And hard. Not as hard as HEI, but they pop pretty good!!
 
This is going to look BAD, and it is, BUT it is not oil, this is all carbon. All 6 are covered, #1 and #6 are the cleanest. They are located at the far ends of the intake manifold, so makes sense.

20261120_183652.jpg

#2 and #3:

20261120_183659.jpg

20261120_183702.jpg

#5, not as bad:

20261120_183709.jpg

#1:

20261120_183719.jpg

All 6 are black, middle are the worse. Not oily or wet, all carbon.

20261120_184138.jpg

These plugs did not have many miles on them when the Jeep was parked 6 years ago. I am hoping the combination of old gas, dumping gas/ spraying brake parts cleaner down the carburetor to get it to fire up, spraying two cans of carburetor cleaner down the carburetor, and all the gas tank additives caused this.

Handy dandy service manual the above spark plug picture came from, I absolutely love the cover art on this book!!!

20261120_184528.jpg

So, six new spark plugs installed, driving/running about 95% perfect again. Drove it around for about 45 minutes tonight, all speeds, lots of stop and go, running great and gets better the more I drive it. Going to burn two tanks of fuel through the engine, pull out the spark plugs, and see what they look like. Hoping all this is carbon/crap fuel/additives, especially how all 6 plugs were fouled out. Not thinking oil burning, especially all six cylinders, and the plugs are dry. We will see.

Look forward to driving it, especially since it is running really well again!! Surprised it ran as well as it did before swapping out the spark plugs!!!

20261120_213930.jpg

That's it for now.
 
Last edited:
Back
Top