• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Storage options for bed of scrambler

Oakley

BENEFACTOR
Gold Member
Lifetime Member
SOA Member
City
Cumming
State
GA
I have looked but did not see any talk about storage ideas for the back of my scrambler. I was thinking about some sort of bolt in drawer system. As mine is a hard top with bulkhead there is just no room to store any gear coolers etc.
Just wondering what others do in this situation. Anything I put in the back now would just slide around and mess everything up. When I pulled it out of the woods someone had put a small aluminum truck box in the back but as you could imagine it looked horrible.
 
I have looked but did not see any talk about storage ideas for the back of my scrambler. I was thinking about some sort of bolt in drawer system. As mine is a hard top with bulkhead there is just no room to store any gear coolers etc.
Just wondering what others do in this situation. Anything I put in the back now would just slide around and mess everything up. When I pulled it out of the woods someone had put a small aluminum truck box in the back but as you could imagine it looked horrible.

I like the storage box I got from GR8TOPS. It carries enough supplies and still leaves me room in the bed for other items. It sits below the top edge of the bed so is low profile. I mounted it using the existing holes for the rear seat.3.jpg2.jpg
 
That seems to fit in there nicely. Also lockable is a plus. thanks for the pictures.
 
That seems to fit in there nicely. Also lockable is a plus. thanks for the pictures.

I run a full soft top, but I have been looking for some ideas as well. I like the idea of lockable AND water tight storage. I have not found anything in particular that fits my needs on the market as of yet. I have contemplated building my own slide out drawers at some point.
 
The previous owner of my Jeep installed these neat tie down rails. I keep my spare tire in the bed and ratchet strap it down to this. I canIMG954384.jpg tie down most anything else as well that I want to transport in the bed.

I also built a rear shelf that pivots off of the inner fenders and covers the area behind my back seat. It's not theft proof but what really is. It keeps things out of sight pretty well and also serves as a solid platform to store things on top of. I can post pics if interested.
 
Last edited:
We are always open to new ideas that others come up with.
IMG_20200708_104543766.jpgIMG_20200708_104624743.jpgIMG_20200708_104426331.jpgi usually use the bed like this or w/o the backseat then I move the spare where the seat is and carry gear under the deck lid. And I can also tie stuff down to the top side of the deck.
 
Nice. What hardware do you use to mount your hi lift jack ?
Just an L bracket, bolted through the lower factory hole in the roll bar. I spaced it up a bit so the jack runs parallel with the roll bar when the bottom of the jack rests on the floor. I also screwed a rubber bumper onto the end of the bolt that goes through the jack rail for the deck lid to rest on.IMG_20200818_085743780.jpg
 
Nice. What hardware do you use to mount your hi lift jack ?
When I had mine mounted that way, I used 3" muffler clamps with those long hex nuts you can get from Ace with another bolt i turned into a stud. I had cut down shock bushings on either side of jack frame with a wing nut hold it down. I have changed all that going to a full top so I doubt I have any pictures of it.
 
For storage, I have an 8 inch deep tuffy pull out drawer mounted behind my rear seat in the Scrambler. I built a rack and mounted on top of the pull out drawer, for more strength to support an ice chest.
My high lift Mount It’s very simple. I took a long 3/8 bolt and cut the head off. Heated it up and bent a candycane hook where the head used to be. Then I just simply hooked the highlift Jack, ran the boat through the factory roll bar hole, and tighten the nylon lock nut on the bottom side to pull the jack down tight so it wouldn’t rattle. The bottom footprint of the highlift Jack slides over a stud that I installe7CFF20DA-F9FF-4905-8E8C-4CB971E1CDCB.jpeg6BFA3751-1909-46E0-B154-BDCEA56DC877.jpeg77B79264-964B-4ECA-BA8F-A64D548AEF2E.jpegCF6C8C6E-0F71-4816-A221-FC7644E4D38E.jpegC8B1D2F8-B9EF-4455-8321-869173BCB06F.jpegAE313239-46E7-46DC-A3AF-36D8E57D3A3A.jpegd at the bottom of the rollbar. This setup has been very secure and has been in use for better than 15 years.
 
I mocked up rear quarter boxes for the Scrambler that fit where the Lido ones went. Mine will be out of 14 gauge metal with a lock, 9 inches at the widest point and nearly as tall as the bed side. My neighbor, that does welding, will make them up when he gets a chance. I asked him about making them up in quantity. He makes small stoves and I thought he could add these storage boxes to his product line. I ordered hinges and locks I need to get to him. Those rear quarters just seem like the ideal out-of-the-way place for storage.
 
I went and talked to the guy I had do my interior on my 65 442. He can make me a great cover for my bed but I’m just not happy with having all the snaps down the side of my bed. I am currently working on other options.
option # 1 would be to widen top of bed with steel 2 inches to the inside of the roll bars all the way around. This would then allow me to put a hard roll and lock cover system on
66540B92-7A0B-46E7-9486-1AC81D051381.png
any thoughts on this idea? Or do I just go with the snaps
 
I think that sounds pretty cool! I wouldn't want the snaps either.
 
Back
Top