• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Swapped MC2100 to 258 problems.

flashover604

Scrambler Junkie
Lifetime Member
City
Lancaster
State
Oh
Hi all,

I just got done swapping an MC2100 onto my 258 last night. It came off of my hangar queen 75 cj5's 304. It's a 1.08. I got the jeep to START, but it runs horribly and smokes like nothing I've ever driven (including a '23 T-Bucket with a 289 with dual Holley 600s). I'm sure that the main jets are too large. They're 50s. I plan on picking up a couple 47s and swapping them in. As for the vacuum ports, I plugged every one except the large one on the rear drivers side which I have going to my brake booster and the front drivers side by the air mixture screw is going to my distributor vacuum advance. I took the choke from my BBD, reversed the coil inside, and fitted it to the mc2100 in place of the manual choke that was on the cj5. There was a port on the bottom of the choke that I plugged as well. It will start, but it runs really rough, REALLY ROUGH, and smokes like an old highball train.

Any suggestions besides the bigger main jets?


Any help would be appreciated!



 
Also, I believe the carb was originally on an automatic. It had the spring/diaphragm dashpot up by the throttle linkage.

It also has Custom 8 stamped into it and an "8" cast on the bottom. I can't find any info on that.


 
Is your timing off? Are you sure the vacuum advance is hooked to the right port?

:shrug:
 
I don't think that the timing has changed, but I'll look into it. I pulled the top of the carb after I shut the jeep off and the bowl was almost empty.


 
All I have hooked up on mine is the vacuum advance (small nipple on bottom front) and the PCV which is hooked to the large nipple on the back of the base. I'm running a 47 and a 46 in one and 47s in the other.

I would unhook the brake booster until you get it tuned, then figure that out. What is your timing setting?

I don't think the main jets should matter when it's at idle. I could be mixing that up with my old Weber.
 
I initially plugged everything except the vacuum advance line going to the small nipple, drivers side front. I'll check the timing in a couple weeks. I said "to heck with it" and took the family to Florida for a week plus vacation!


 
I'd guess the power valve may be blown or the needle/seat isn't sealing off.

Sent from my SM-G920V
 
I replaced ten power valve with the new one in the rebuild kit. It's the taller two stage versus the single stage I took out. If the needle/seat was bad, I would expect it to overflow. The seat stops fuel from coming in when the float pushes the needle down. The filter is a little above the inlet, so fuel would have to flow uphill out of the bowl, into the filter, and back to the the tank via the return hose.

What exactly does the power valve do? Where does it route fuel?

I believe I have three outlets in the bowl, (not counting a defective needle/seat.

1. The main jets.

2. The accelerator pump which pushes fuel to the two venturis.

3. The power valve. Where fuel goes from here, I haven't a clue.

I replaced the needle and seat and set the float at 7/16" from top of float to top of carb with the supplied gauge. I replaced the accelerator pump and the little red diaphragm under it and made sure it was pulled through completely. I replaced the rod that presses the AP. I replaced the power valve and gasket and hand tightened firmly. The carb isn't leaking externally.

I'll order a set of .047 jets and see if they change anything, and I'll double check my timing.

I'd still love any ideas. I'm out of my own!


 
I looked up power valves on eBay and found several different sizes from #25 to #105.

Any idea which I'd need?


 
What exactly does the power valve do? Where does it route fuel?

The power valve is vacuum signal controlled enrichment. At steady state(no butterfly movement) operation, the powervalve opens up to give enrichment where the accelerator pump is inactive. There are 1, 2, and 3 stage powervalves. At different levels of vacuum, it will "stairstep" up extra fueling until at no vacuum it's all the way open.
 
Ok. That makes sense. Any idea what the different sizes are? Or better yet, which size I should get?

Also, I understand that I need to fabricate an arm to change the carb from rear pull to bottom pull. Do any of you guys have any pictures of yours? I know the guy on eBay sells one, but I'd like to make my own. I'm also going to make a bracket to move the return spring forward of the carb instead of below it.


 
Ok. That makes sense. Any idea what the different sizes are? Or better yet, which size I should get?

Also, I understand that I need to fabricate an arm to change the carb from rear pull to bottom pull. Do any of you guys have any pictures of yours? I know the guy on eBay sells one, but I'd like to make my own. I'm also going to make a bracket to move the return spring forward of the carb instead of below it.

Order a throttle cable from a 1980 CJ-7 with 304. Snaps right in place, no fabbing required.
 
Does the 1980 cable just get re-routed to pull backwards or is there a different bracket that it mounts to?


 
d80ffbd5d835f6c5615b709231043832-1.jpg


Also, this part that is circled... I had to remove it due to the throttle linkage hitting it. I couldn't rotate the linkage more that few degrees without hitting it. The large port went to my brake booster, the small port that is capped off in this picture went to my vacuum advance. I plugged the manifold with a pipe plug and dope and used the large port on the bottom back side of the carb for the booster and the small front drivers side port for the distributor.


 
Does the 1980 cable just get re-routed to pull backwards or is there a different bracket that it mounts to?

Snaps into the firewall on the pedal end, and you can fab a square hole for the other end to snap into if you want it to be pretty, or just zip tie/wire the other end to keep it from flopping around. Mine is zip tied. Did it 10 years ago as a temporary fix, and haven't touched it since.
 
Ok. Got it.

First the "no run at idle"...

HUGE vacuum leak. The gasket that seals the carb to the adaptor was wrong. It left a 2"X1/8" opening that I THOUGHT wasn't open to the bottom of the carb. I re-used the original spacer and it idles great.

Second, the smoke.

I put new 47 jets in place of the 50s and reinstalled the power valve. When I originally installed it I don't think I tightened it enough, and I had two gaskets stacked instead of just one. Tightened it up with none gasket and...no more smoke.




 
Back
Top