• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Swapping Springs...

John N

Addicted....Ex-SOA VP
Lifetime Member
SOA Member
City
Rockville
State
VA
In an effort to get a little more lift in the nose of my Scrambler, I ordered a set of 1451 RE rear springs. I have a set of RE springs on there now that are probably 5+ years old. The springs came today. I bought them about 5 weeks ago when they ran a free shipping promo. I am putting the new set in the rear and putting the used rear set in the front. I got the rear done already....twice or so. I got them in and was going over everything and found the spring center bolts were loose. I went to tighten them and they weren't loose....they were stripped :banghead:. I called RE, a bit pissed since I'm taking apart what I thought I'd just finished. They agreed, without any hassle, to next day a new set of center pins to me and suggested I use 3/8" grade 8 bolts to replace them anyway. I found the bolts, while I was still on the phone, so they're still sending the center bolts, just not next day. Ground the heads round and reassembled. The rear is done and sitting only 1/2" higher....so far...so good.

On to the front.............
 
That sounds like something that would happen to me...everything is two steps forward, one step backward! Let me know if you need an extra set of hands to get the front done.
 
The front........

The front went easier. The rear springs that I put in the front, both had bent center bolts. Now, like the rear, they have grade 8 bolts for new center pins. Also, I put in new steel, 4 degree shims instead of 2.5 degree aluminum. I didn't get the tires back on for a measurement, I found the front brake pads looked bad; so, new pads on tomorrow.

Thanks for the offer Mike.
 
John- did yours originally have 1450's front and 1451's rear? Mine's like that and even when I sit on the tailgate the front is still 1 1/2" lower than the rear. Been thinking about swapping front to rear- did you ever try that? I think my 5.3 and winch way a lot more than the tire carrier...:D
 
John- did yours originally have 1450's front and 1451's rear? Mine's like that and even when I sit on the tailgate the front is still 1 1/2" lower than the rear. Been thinking about swapping front to rear- did you ever try that? I think my 5.3 and winch way a lot more than the tire carrier...:D

No, I didn't think of that. Yes, they were 1450's in the front and 1451's in the rear. Now it'll be old 1451's in the front and new 1451's in the rear. I will be able to tell you how they do in the front with a winch, V-8 and heavy bumper. I have seen how much the rear will go down with 4 people and gear, I don't think the 1450's would cut it, if that's possible for you.

Anyone with recent production springs from RE should check their center bolts, too.
 
Swap Completed....

I got the springs all done and re-did my measurements. I have exactly no real gain. I picked up 1/4" -1/2" in the rear and nothing in the front. The Jeep is sitting more level.

I now have the shackles adjusted well, new brake pads, steering, suspension and u-joints lubed and more castor in the front. It actually handles much better. Plus a few other adjustments made and couple more things to take care of. After doing the brake pads, I now have a sticking brake caliper to replace.
 
Caliper replaced and brakes bleed. The pins were stuck in the bushings. I could have cleaned it up and not replaced it :banghead:, but I'd already bought and painted the replacement. I found the issue as I pulled the old one off.
 
Back
Top