• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

TF999 hard tp shift out of park position? What could cause this?

JeepScrambler

CJ-oholic
Lifetime Member
SOA Member
City
Claflin
State
KS
I'm in the process of installing an AMC 360 V8 in place of the 258 in my '84 CJ7. The Jeep currently has TF999 automatic transmission that was rebuilt about 15k miles ago. Ever since the rebuild of the transmission, it has been hard to shift out of park. It goes through all of the other gears just fine and even goes back into park normally. The issue is just when trying to shift out of park. I had a B&M ratchet shifter in the Jeep before and just chalked the hard shifting out of park on the aftermarket shifter. You had to slam the shifter pretty hard to get it out of park. In the course of the 360 swap, I have decided to go back with an original tilt column shifter so my wife can drive it easier. I am using an Ididit column cable shift linkage setup. Got the cable column shifter installed and and still having the same hard shifting out of park I was having before.

The cable is adjusted and lines up with the gear indicator correctly and shifts fin in all other gears. When I disconnect the cable and try to manually move the lever from the park position, it is still really tough to get it to shift out of park. This leads me to believe it is something internal. Is there some sort of internal adjustment on this or could there be an issue with the shifter detent in the park position? I have been searching for hours and cannot find anything similar to the issues I am having. Anyone have any ideas on what could be causing this and were to look on how to get this fixed? Jeep will be ready to run in a few days but want to get this taken care of before hand. Any help is appreciated!
 
I had the same problem several years ago. Trans shop that did the work had installed the park detent/lock spring incorrectly. they repaired it and said it was a simple fix. Of course I was the one that pulled the trans back out and took it to them, then reinstall it. :shrug: :wave:
 
I've never really tore into a TF999 before. Is the park detent/lock spring something I need to drop the valve body out of the transmission to gain access to?
 
I've never tore into one either. No knowledge at all on the internals. Sorry. :wave:
 
check your linkage against the firewall you may find a bolt head causing the hang up that was my problem on 2 CJ7
 
Updating this thread as I finally figured out and fixed what was causing my transmission to be hard to shift out of the park position. After some extensive searching, I found this site that described my problem I was having http://www.4wdmechanix.com/Survival-Upgrades-for-Jeep-and-Dodge-Ram-Automatic-Transmissions?r=1. The gear shift selector detent ball had wallowed out the bore in the TF999 valve body where it rides. This was causing the detent ball to wedge against the shift selector. Luckily, a company called Sonnax offers a "Detent Sleeve and Ball Kit", part number 22771-12K. To install, it also requires their "Reamer Kit", part number 22771-TL12 to bore the detent ball and sleeve hole to install the new stainless steel sleeve. It does require removing the throttle body from the transmission.

While I had the throttle body out, for peace of mind, I decided to go ahead and installed a Sonnax manual valve (part #22771-09) that "allows fluid charging of the torque converter in Park position." I also installed a Sonnax Lube Regulated Pressure Valve (part #22771A-02K). "This helps assure adequate fluid to the converter and works in conjunction with the new Sonnax manual valve." And since I had the transmission opened up, I adjusted the both bands in the transmission. I'm pleased to say that now after installing the Detent Sleeve and Ball Kit and other parts, the Jeep now shifts better than it ever has while driving, and the Jeep will now shift out of the park gear properly. A big thanks to Moses Ludel and his post on 4wdmechanix.com for his information that helped me fix my hard to shift out of park problem!
 
Great work and thanks for sharing. I'm sure this info will come in handy for others down the road. :thumbsup:
 
Thanks for posting this. I have the same problem with my TF999, that I will eventually have to get into.
 
Back
Top