• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

TF999 - Rebuild Options

ag4ever

Average Nut
BENEFACTOR
Gold Member
Silver Member
Lifetime Member
SOA Member
City
Richmond
State
TX
I have 3 TF999 transmissions, one I know is not working correctly and I believe to be the original transmission in the Overlander. The other 2 are from parts purchases over the years.

Overlander one is:
8933000917 - 4WD JEEP, Export, Non-lockup
7992 date code (Wednesday, June 15, 1983)

Second one is:
8933000913 - 4WD JEEP, Lockup
8083 date code (Wednesday, September 14, 1983)

Third one is:
K3238773X - 4WD JEEP, Lockup* (input shaft indicates non-lockup)
7266 date code (Friday, June 19, 1981)

The second and third transmissions are completely unknowns. All I can confirm is the second has the lockup torque converter input shaft and the third has a non-lockup input shaft (despite the code indicating it should be a lockup torque converter). I have not pulled the transmission in the overlander, so I cannot confirm if it is a non-lockup torque converter like the code indicates. All three appear to be in the same shape externally. None look abused or have obvious damage apparent. All three decode as TF999 (heavy duty versions of the TF904). Overlander leaks transmission fluid from the dip stick tube at the transmission case. Bad o-ring I assume.

So, which transmission should I rebuild for use in the overlander?

I have read conflicting opinions on the lockup torque converters in the TF999. Some like them and appreciate the improved fuel economy from the 250 +/- rpm drop, and others bemoan them claiming they are unreliable pieces of junk that fail and takeout the rest of the transmission in the process.

Should I rebuild the original transmission assuming it is a non-lockup, rebuild the spare ‘81 non-lockup, or go to the ‘83 lockup one?
 
Two of my Scramblers have the non-lock up TF999. My third Scrambler has a lock up TF 999. I definitely prefer the lock up over the non-lock up. It almost feels like the transmission shifts into an extra gear when it locks up.
 
I have a couple of TF999's in the parts shed, with the intention of swapping one into my green CJ7 at some point.

Where are the tag numbers on them to get those codes? I didn't really look at them when I picked them up, just stuck them in the shop.

You going to do a rebuild thread on one (with lots of pics!) or have it done by someone else?
 
Isn't most of the lockup stuff in the torque converter, there's some complexity in the hydraulic circuit but the important bit is the converter.
I mean that the quality of the convertor is the driver for the life of the lockup system.

You may be best to dissemble all 3 and pick the best parts. I wish i could have found a better valve body for mine.
 
I have a couple of TF999's in the parts shed, with the intention of swapping one into my green CJ7 at some point.

Where are the tag numbers on them to get those codes? I didn't really look at them when I picked them up, just stuck them in the shop.

You going to do a rebuild thread on one (with lots of pics!) or have it done by someone else?
1B750217-DB64-4774-8EB2-EE3ED520BD0F.jpeg
On the driver’s side above the pan. First number is the part number, second is the date code, third is the production sequence number for that day.

This is the input shaft for a non-lockup torque converter:
C2AA87C2-EBE7-481B-AAA2-8B55B74B2BB5.jpeg

This is the input shaft for a lockup torque converter:
3B946425-B30D-49D3-A0EB-EBFF729DFFF5.jpeg
On this one, the machined portion fits in a recess in the torque converter and fluid passing through the input shaft controls the lockup clutch.

I plan to rebuild it myself, once it climbs up my priority list. Currently, finishing the installation of gas lines in the house are higher up the list. If I was smart, I would get Precision Transmission in Amarillo rebuild it for me, but they don’t allow carryout service. Only full remove, rebuild, installs. I am sure there is a good shop in Houston, but the one I always used (Shine Transmission) is out of business. Seems nobody really works on these relics anymore.

I do plan to install a Transgo Shift kit, probably a level 1, but I may go level 2. Not going full manual level 3!
 
Last edited:
Isn't most of the lockup stuff in the torque converter, there's some complexity in the hydraulic circuit but the important bit is the converter.
I mean that the quality of the convertor is the driver for the life of the lockup system.

You may be best to dissemble all 3 and pick the best parts. I wish i could have found a better valve body for mine.
Most of the work is in the converter, but it does use a different valve body.

For parts, https://www.transtar1.com/ is the recommended place to buy quality used components as well as new parts. You might be able to source a “new“ valve body from them.
 
View attachment 102026
On the driver’s side above the pan. First number is the part number, second is the date code, third is the production sequence number for that day.

This is the input shaft for a non-lockup torque converter:
View attachment 102024

This is the input shaft for a lockup torque converter:
View attachment 102025
On this one, the machined portion fits in a recess in the torque converter and fluid passing through the input shaft controls the lockup clutch.

I plan to rebuild it myself, once it climbs up my priority list. Currently, finishing the installation of gas lines in the house are higher up the list. If I was smart, I would get Precision Transmission in Amarillo rebuild it for me, but they don’t allow carryout service. Only full remove, rebuild, installs. I am sure there is a good shop in Houston, but the one I always used (Shine Transmission) is out of business. Seems nobody really works on these relics anymore.

I do plan to install a Transgo Shift kit, probably a level 1, but I may go level 2. Not going full manual level 3!
Thanks for the pics. I'll have to dig mine out and see what I have.

I've always driven sticks, but since we have 3 CJ's and the womenfolk are always crying about not liking the clutch, I figured I would put an auto in one of them sooner or later.

No one around here that will do a bench build (I live in the boonies) so I'm in the same boat as you as far as shops.

I'd love to see pics as you go if you wanted to do a build thread (hint, hint).

As far as the converters go, aren't you supposed to always use new? From what I understand there isn't any way to test them, but they can be rebuilt/ drained/cleaned, and they should always be replaced when a slushbox is rebuilt.

I don't know much about them. I traded an extra T176 for two TF999's, an auto column, Lokar kickdown, and auto brake pedal. The guy I traded with said the transmissions were both "good" but I would rather go through one than risk installing one and having to pull it back out.
 
I will be replacing the TC. If they are bad, they destroy the transmission. No chance risking it. There are a few shops around here that rebuild them, or they are listed as available on Transtar’s website.

I plan to do a build thread once I start it. I already have the master rebuild kit, bought a couple years ago.
 
I have been driving the Overlander more each weekend, and I am finally frustrated enough with the poorly shifting transmission to start a rebuild of a spare to swap in.

This will be a “real time” post following the rebuild process, so if it take a while you can blame one of the below reasons.

1.) Other obligations are preventing my devotion of time to this project

2.) I found a part that needs replacing and as a result waiting on part delivery

3.) The rebuild has become ”work” and is no longer an enjoyable experience. (I learned this lesson a long time ago from a friend of my wife’s family. Once a hobby becomes work, step away and come back tomorrow with a refreshed state of mind. Thank you Jerry Bramlett! This philosophy can be applied to sooo many facets of life.)

All that said, I am striving to do this as quickly as I can, I want to drive the Overlander more, and the transmission is preventing me from trusting it on longer drives.

So, should I start a new thread, or just continue with the rebuild here?
 
First step, cleanup and light disassembly.

9D0BC444-6507-417E-B82A-2D3ACF742DCC.jpeg

FE1D4D48-875B-4953-942F-2CAF2D277119.jpeg

7D3238F5-D400-4E0A-9895-E266A519B303.jpeg

Now that the thick crud is off, dip stick removed, tail housing removed, on to shift lever and switch.
 
New thread so everyone searching can find it easily. Just kidding. What ever works for you.
 
Back
Top