• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

The little flatty--for a lil fella

So here is where I hit a dead end and I can only "roughly" figure for the power steering components till I get a rad in place. But I am shooting to put the res tank on the passenger side. This will give plenty of room and keep it high enough to not cause any problems.

gmb-289.jpg


gmb-290.jpg
 
Time to get the radiator mounted..

I want to run it a little more forward ( for when dale wants to toss that lil 3.8 for a good chev 4.3 :redneck:) since the option is there..

gmb290%7E0.jpg


I want to remove some material and also make a nice flat surface. It looks like a fat kid sat on the area where the rad would be.

gmb-291.jpg


All cut flush. I only removed about 3/4-1" but now its a nice flat surface.

gmb-292.jpg
 
First thing I know I need to remove is this big fat turd..

gmb-293.jpg


Nothing like cutting something in pure anger...

gmb-294.jpg


I made caps and welded them into place to give a good footing for the new cross member to sit.

gmb-295.jpg


Time to build the mounting setup for the rad.

gmb296.jpg



Hope to have something soon...
 
So I have been poking along on it for the last couple of weeks and just running myself into circles. Did 3 different setups for the rad and scrapped them. Well like anything it just hit me and I went with it and got the result I was looking for. But in any case the rad is now mounted/ruffed in(gotta trim it on the outer edges) and damn solid.

gmb297%7E0.jpg


gmb298.jpg


So with the rad mounted the ps cooler location just fell into place. So next I will get that mounted and then onto the res tank (which I have a rough idea there)...

I have a bunch of free time finally so I am going forward...
 
This definitely took some time to find the sweet spot for this but I finally found it (picked up another 90 degree ARP fitting). The hard part was keeping it in place so I could make the standoffs--but I figured it out..

gmb300.jpg


Got them made and tacked into place and pulled the engine cage and burned them in.

gmb301.jpg


gmb302.jpg


So next back to the cooler.... Hopefully have that in place tommorow..
 
So my original plan was to mount the p/s cooler under the new cross member. All my plans went out the door when I realized I had pulled the winch and with it in place there was a high chance of the cable smacking the cooler.

So I went with my second location which is still a good spot.

gmb303.jpg


I got the rad back in to test fit everything and it looks great. Plenty of room to either run a mechanical fan or an electric fan.

gmb304.jpg


So all the metal work under the hood is done except the clutch master which will only require a few holes in the plate next to the brake booster.,

So in the morning I move back and start the second battery tray that Dale wanted.
 
Got the new base made up.

gmb305.jpg


Bent up the support tube.

gmb306.jpg


Got the new battery mount finished. I just have to cope the center tube and its ready to weld in..

gmb307.jpg


gmb308.jpg
 
Got the battery tray mounted. I think I did a decent job of duplication...

gmb309.jpg


gmb310.jpg


So scratch that off the list...
 
I went ahead and got the hydro stuff plumbed. I need to get some more 5/8 material and redo the hose from the res to the pump..

But another thing scratched off the list...

gmb312.jpg


gmb-313.jpg


gmb-314.jpg


gmb-315.jpg
 
Last edited:
It took a bit of work but I finally got the brake pedal portion of the pedals done. It was a pretty tight fit to get the correct throw on the master and miss the steering shaft.

gmb316.jpg


I got the location for the clutch master and the hole cut in the firewall--so hope to have a dent in that tommorow night.

Also one thing I will need you to do dale is fit Jackson for the pedals and make sure he can reach them. If not I can cut and turn them but I figured I would let you have the final call on that apon its return trip..
 
Got the clutch master installed. I have a little more work to do on the pedal but its pretty close to being done...

gmb317.jpg
 
Ok I got the clutch pedal assy done up--turned out perfect..

gmb-318.jpg


Here is the pedals..

gmb-319.jpg


Actually Dale I still want ya to fit Jackson on the pedals. Since these things have such a shallow foot area I can't push them forward without cutting the pedals down and raising the pad.
 
My head is spinning !!!!
I feel an anxiety attack coming on

Very impressive work my friend !
 
Nice, nice, nice. I applaud your attention to detail. Everything look well thought out. You the man!
 
Thanks fella's. I wish I could have gotten it done quicker but I am happy with how it has turned out to this point...
 
Back
Top