• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Tip of the day

I replaced my stock steering linkage (drag link/tie rod) and used large hose clamps to clamp it to the inside of the frame rail. The frame is straight, the linkage is ready to simply slap on if something happens to my heavy stuff and I know the alignment is pretty close. Even left the steering damper bracket on so I don't have to set that up either
 
Dont know why, but here is my weak submission anyway.
Here in Va. we are required to use a front AND a rear license plate. As it is difficult to find a suitable location on a winch bumper, I have in the past used large clips normally used for attaching a mag lite to a floor board. The idea is that you press the clips to the vertical rollers of the fairlead and rivet the license plate to the clips. I realize this thread is difficult without pics, and I will look for some to post.
Hope this helps SOMEBODY.
Todd
 
DC CJ8 said:
Dont know why, but here is my weak submission anyway.
Here in Va. we are required to use a front AND a rear license plate. As it is difficult to find a suitable location on a winch bumper, I have in the past used large clips normally used for attaching a mag lite to a floor board. The idea is that you press the clips to the vertical rollers of the fairlead and rivet the license plate to the clips. I realize this thread is difficult without pics, and I will look for some to post.
Hope this helps SOMEBODY.
Todd

Nice! They make a bracket for sale that does this same thing, but I bet your solution is cheaper and can be found at almost any hardware store.

Glad to see this came back up, now we have to work to keep it up.

I love the idea of strapping the spare steering setup to the frame too!
 
I used the Maglite clips also. I used the front mounting plate (plastic), from a Cherokee and, with a little trimming, bolted the clips into the backing while securing the license plate to the front. Perfect fit and easily removable for the trail.
 
Ok, here's one from my soft top days.

I always hated the idea of rolling up the attached rear window, because I knew that grit would scratch it up. I figured out that if you used 2 long bungee cords, hooked one to each end of the rear window lower rail, and then hooked the other end to the top of the roll bar on each side, the rear window would be held up tight and parallel to the floor, out of the way, and get no scratches.

Here's a crude pic- the red line represents the rear window, the dark green is the bungee.

attachment.php
 
I did that with my CJ5 too Randy, but I went ahead and put grommets in the rear window, the fabric part, and used that for my bungee cords to teh roll cage. worked well


another thing, older Ford sedans, early mid 1970s used small power steering coolers, even the 6 cyl mavericks, I keep an eye open in the pick a part for them and grab them up for a couple bucks per. Easy to install on the low pressure side of all my vehicles, just in case.
 
Last edited:
Ball valve for the parts washer....

Most parts washers have a drain plug that leaves much to be desired. When removing it, that nasty funk you are trying to drain to dispose of usually goes all over you and everything within a 10 mile radius. So.... I fixed it with a handy little drain valve and a barb on it for a hose so I can direct the fluid into a container. In order to adapt to pipe threads for the ball valve, I had to drill and tap the original plug since it's threads were your standard bolt threads and not NPT like the valve body. No biggie if you have a pipe thread tap, correct size drill bit, and a drill press.

No mess solution to draining a parts washer:
PWSM1.JPG
 
Hour Meter

Got another one...
I added an hour meter to my air compressor so I know when to change the oil. My use of it is so sporadic that it's impossible to know how many hours are on it and most compressors manufacturers recommend changing it according to hours used.

Got the meter from Grainger.

HRMeter.JPG
 
Is that just a box fan, copper coils and a water filter? Nice... probably could have used that in NC as freaking humid as it was.


Here's a tip to keep this going: get an assortment of the plastic thread covers (like used on exposed screw ends in kids outdoor toys) to put on the ends of the soft top door rods to tighten them up in the holders and keep rattles to a minimum.
 
bigwalton said:
Is that just a box fan, copper coils and a water filter? Nice... probably could have used that in NC as freaking humid as it was.

That's it.
Fan - $12 on sale at Lowe's at the end of the summer season.
Copper - $50 - biggest expense due to cost of copper right now.
Filter - $20 or so at Lowe's
Wood - had on hand (Contour cut on band saw)

It was unbelievable how much water came out of the air that thing was pumping. Never had water in my lines after that little mod. The old Craftsman kicked the bucket (oil-less) and was replaced with a big honkin' Ingersol Rand. I'm going to rig something up on it too like I did with this one above but may use a tranny cooler instead as long as I can find one that can take the pressure.
 
Tip of the Day - Torx Seat Belt Removal

I have found a way of removing the rusted torx bolts that mount seat belts to the floor of our Jeeps while not melting the belt material or plastic sheathes. I use a sharp 7/16" drill bit in a 1/2" Milwaukee Drill and use a garden hose to provide water to keep the bit cool. The seat belts only need to be hung to dry after drilling out the torx bolt. I am sure the drill bit does not stay as sharp as when you use cutting oil, but you can salvage the belts perfectly. Now all you need to do is drill out the remainder of the bolt and chase the threads clean.
 
Back
Top