• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

TJScrambler - Getting Started

This is my set of stands for the frame, they worked nicely and then I modified the same ones for the body.
https://www.cj-8.com/forum/showthre...the-end-and-a-fresh-start&p=254920#post254920

For the body I installed a cross brace and a set of casters for mobility. I used my old front SS bumper for the front mount and a piece of angle iron for the rear. I rolled that set up in and out of the tent, sideways across the driveway. onto a trailer, into the sandblast shop and back by simply removing the stands off the rotating ends. I did a lot of hammer dolly work and panel work and never had any flex issues. I know I had less than a hundred bucks in that set up and sold the stands on Craigslist for $50 when I was done. The body wouldn't do a 360 but it would roll 90 to either side which was more than enough to work on it.
https://www.cj-8.com/forum/showthre...the-end-and-a-fresh-start&p=277602#post277602
https://www.cj-8.com/forum/showthre...the-end-and-a-fresh-start&p=277603#post277603
 
Last edited:
Still selling parts to get the rotisserie money

23b5e5434ed2fc8c3a888c5cfb700ea7-1.jpg


cb
Sent from the garage
 
Since I have now installed my body back on the frame and do not plan on using the rotisserie again I have given it to my painter as a tip. The rotisserie sure comes in handy but it's also hard to store when you are not using it. With a understanding that if ever need it I can borrow it.
 

Attachments

  • 001108.jpg
    001108.jpg
    205.7 KB · Views: 143
  • 121213.jpg
    121213.jpg
    224.3 KB · Views: 144
Last edited:
Rotissierre on order should be here next week. Swapped tires around and trying a new hood look

d68860afcfa90746b597bc628476f29f-1.jpg


bb8d2c500f617ffe7b281a56d94d75d7-1.jpg


706821c09379adcb8b523e6d5154b8ec-1.jpg


cb
Sent from the garage
 
While I am waiting. Tie rod flip for silver jeep axle swap. 4.56 locked wide tracks with 6 bolt outer hubs

9fbb7c4fa3a9a4fbfcfa7b2f0d90aa30-1.jpg


cb
Sent from the garage
 
I worked more on the front axle last night.
Got the new pads and caliper installed on the driver side.
This followed putting new rubber sleeves and lubing up the bolts for no seizing.
All in all, I just have to finsh the other side, drain the fluid, new "lube locker" gasket and refill with new fluid.

The interesting part is I got a call from the Freight carrier in town, apparently I have ton of metal on a pallet I have to go pick up... pics later this evening if I get it.

cb
 
Assembly completed. Next up get all stuff out of the tub and mount it

ccaea05a1e91d96c0aabe0c54cb2d6f0-1.jpg


cb
Sent from the garage
 
Front Axle is done for the CJ7, so that goes on the back burner until I re-gear the rear with 4.56/locker/1 piece updates, probably over the winter or spring.

Biggest issue now is stripping down the 8 to the tub, to remove it and get it on the twirler... neighbor said he could help today, I laughed... then thanked him.
Told him I need a full day of stripping it down before I can do anything.

cb
 
I like ! If the jets had made the playoffs I'd come up and help you and watch a game with ya like I did many many jeeps ago..
 
and then of course, since I have a plan, it doesn't mean I won't buy something else to try to do something with ;)
 
When I installed my tub on the rotisserie I had to also install these firewall braces. I could see the body trying to flex under the doors. You won't have that problem as long as the spider rockers are still in place.
That is one fine flipper.
 

Attachments

  • 002922.jpg
    002922.jpg
    204.9 KB · Views: 91
  • 008824.jpg
    008824.jpg
    199.2 KB · Views: 92
The rock sliders that are still bolted on are essentially angle iron, thick stuff, so there didn't appear to be any flex.

cb
 
Back
Top