• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

What did you do with your Scrambler today? July 2014 version

Status
Not open for further replies.
Noticed a wild coolant leak appeared on the driveway since parked outside yesterday. Traced it to a loose hose clamp. Tightened it up and took it for a spin. Parked for 4 hours now and no return drip.

it's da GREMLINS, I tell ya..!!
 
Flew in this morning from Peru and eagerly raced into the garage to make sure everything was cool... Quickly reattached the battery cable to the solenoid (I have a short somewhere that will drain my battery in a matter of days)... and she fired right up. Quick shower and then drove down to the gun store in 115 degree weather and bought myself a new toy... a Glock 42. I love it, now to load up the Jeep for a quick trip to the desert for some plinking, once it starts to cool down! :smokin:

I have some parts to install over the next couple of weeks, a Samex sine wave inverter for the M416, a back-up light (trailer), the BIG air horn and tank (awesome), etc. But first, to the range!
 
Changed the oil yesterday to a heavier weight and it solved my fully heated up noise I was hearing and now have 13 PSI at idle, even in 95+ heat here. Nothing in the oil. Still have to cut open the filter to see what is there. Also, swapped out the oil breather for some hose and a container to help with the oil pushing past the breather. From yesterday to today no oil on the valve cover but also no oil in the container... But I do have a bit of a valve cover leak again.
 
Hot day today in Lake Havasu today, the Jeep did not care for it much... decided to purge itself of some excess coolant. I just love temperamental old vehicles!

I did get the back-up light mounted on the trailer though, same set-up as I have on the Jeep.

IMG_9728.jpg

IMG_9722.jpg
 
I get a little giggle every time I park in one of these. One of the benefits of living in a Granola, Tree hugging state. I used to think it was even funnier when I was driving a Chevy 3500 diesel flatbed.

 
Drilled a couple holes to mount a new radio antenna. More to be done tomorrow...
 
I retrofitted YJ windshield wiper linkage into the CJ windshield frame.
Very easy "upgrade" once you get the balls to drill the wiper arm holes out to 15/16"

Unfortunately, I started this swap thinking I was just going to pull the parts out of the YJ windshield frame that I have and put the parts in a box for later. I just kept going and pretty much didnt stop till I was done. Of course the whole time, I didnt think to take any pictures. :(
 
I retrofitted YJ windshield wiper linkage into the CJ windshield frame.
Very easy "upgrade" once you get the balls to drill the wiper arm holes out to 15/16"

Unfortunately, I started this swap thinking I was just going to pull the parts out of the YJ windshield frame that I have and put the parts in a box for later. I just kept going and pretty much didnt stop till I was done. Of course the whole time, I didnt think to take any pictures. :(

I am very happy I did this for mine. Much more reliable linkage in my case. But I did not have the reservations about widening the holes. I was so frustrated with my old linkage that I was ready to get a whole new windshield (or maybe Jeep).


Dain
 
Installed a new exhaust hanger as mine broke on the way home last night.


Dain
 
Tour of Blount County, Alabama covered bridges!!

yjyjy9ar-1.jpg


a8ajyjed-1.jpg


u3a3yvun-1.jpg



 
I got the riptech kit. I ended up using the motor arm but didn't use the new wiper arms. I didn't like the way they fit. I had arms from another manufacture that gave the angle that I liked better.
 
I finally got a chance to put a used set of chevy ram exhaust manifolds on the cj7. The other set had a stud crack the cast iron on each manifold. I had a guy weld the stud and ear but it only lasted 4 or 5 drives. I found out about it cracking again when I was boiling brake fluid out of the MC. I thought the brake lines were too close to the exhaust so was wrapping the exhaust with a blanket when I found the stud loose.P1010658.jpgP1010657.jpgP1010656.jpg
 
Last edited:
Got the inspection plate on the trans and mechanical oil pressure/water temp gauges imstalled. Both are running at what look like normal.

The other project of the day failed. We cannot get power to the stereo, or maybe a better explanation is the radio wont power on. Might have to bring it somewhere to make sure it works. I havent hooked up a car stereo in twenty years.
 
My Birthday was yesterday so me and the bride took the scrambler out for a Saturday drive to hit a couple Culver restaurants... (butter burgers and frozen custard for those of you not in their franchise area) FREE Sundays on your birthday, so we hit one on Baraboo, one in The WI Dells and one in Portage... so three turtle sundays later.....diabetic coma while watching a couple episodes of Orange is the new black... Second season... And the old girl hit a milestone..80,000 miles.IMG_2294.JPGIMG_2268.JPG
 
Because Eric like to see Scramblers in "action" ....this is from the 4th of July weekend. My neighbor finally got his pontoon of his boat launch so I use it LOL.... Used the scrambler to trailer the pontoon float/dock and then the pontoon... The LJ took care of lowering the dock section down to attach to the float. Oh and some one else showed off their windshieldIMG_2265.JPGIMG_2266.JPGIMG_2263.JPGIMG_2260.JPG frame in another thread so I thought I would do the same.
 
Drove it four hours to say farewell to the day job, no doors or windows and all highway after leaving our town.

Started out with some dirt and a sunrise. Seemed fitting on both counts.
ImageUploadedByTapatalk1406089994.957062.jpg

Also hit McDonald's for a celebratory breakfast, driving through backwards like a RHD boss. The look on the dude's face in the F150 was worth the trouble. Strangely enough, drive thru designers always assume the steering wheels are in front.
ImageUploadedByTapatalk1406090018.377512.jpg
 
Got the auto pedal assembly and non tilt auto column removed and a manual tilt column and pedal assembly installed

ImageUploadedByTapatalk1406168498.460527.jpg
 
H1 steering box installed
Going to swap out to artec Dana 44 hi steer arms and test out some new prototype rock krawler steering 2.5 ton joints I'll post up pics when I start the process
 
Status
Not open for further replies.
Back
Top