Search results

Does anyone have a Rally Tops/Xtreme Tops full hard top they can post a pic of the front windshield mounting area? Do they mount with screws like a factory half cab had top or are there latches? I have a front cage hoop that would likely prevent latches. I don't mind drilling holes in the...

A few have asked to see my gear checklists. Here are a few... Hope they help. Yes...I was a Scoutmaster.... Can't upload Excel files so here are some PDF's. I didn't spend time formatting for PDF as I just use the Excel versions. So these lack dividing lines etc. I also have a tool kit...

What have you used for a clutch master cylinder that has lasted years without leaking from the seal on the firewall side? When I rebuilt my Scrambler, that had the 4-cylinder engine new, I kept what appeared to be the stock master cylinder. I believe it was on there for 40 years and didn't...

Back from the trip to Joshua Tree National Park and the Old Dale Mining District on BLM land. Wow! It was fantastic. There are so many abandoned mines to visit. We did maybe 15% of them. Didn't see anybody for the first three days we were exploring the mines on the BLM land. Then we took...

Does anyone know what these holes are for under the tailgate hinges?

Did the Scrambler come with plastic splash shields that covered the underside of the tub at the rear corners? This is the area where the fuel fuller hoses go through on the passenger side and where the rollover check valve goes on the drivers side. In my parts pile, I only found the splash...

Hello all, I am finally ready (I think) to reassemble my full hard doors on my 1982 Scrambler. I didn't take great pics when I disassembled them. I have read a number of threads, including @spankrjs on the reassembly and have one question that didn't seem to be covered. How does this nylon...

Has anyone used the Revolution Electronics module to add an intermittent function their stock switch and 3-wire wiper motor? I just found this: https://www.revolutionelectronics.com/Products/intermittent-wiper-module/ And supposedly they have a module for the CJ's with a part number of...

Does a stock CJ-8 Windshield Wiper Motor have a spacer like the black one below on @spankrjs picture? Mine looked like this when I tore it down. No gasket/spacer: The previous owner must have done some work on it as the VIN plate is bent up as you can see. Maybe they left off the...

Hi guys, I am trying to get my windshield wiper system in and have an issue where the wiper arms are not properly mounting on the pivots. I used all new Omix Pivot parts: I had to grind out the holes in my aftermarket windshield frame to get them to seat fully. I tried both Omix and...

I know we had a few posts asking about these things. I could not find it. As my build is getting back on the road and trail, I REALLY wanted to use one of them. Lot's of benefits: Small, non-toxic, no residue to clean up, never expire, not going to knock you out if it comes loose, works on...

I have the weld on frame reinforcing side plates and now need to mount my Warn XD9000i winch. I bought a Warn 19310 mounting kit and the outer holes that bolt the winch plate to the frame brackets don't line up now that the frame plates created a wider span. Picture below. Has anyone dealt...

Hey guys, What is the purpose of the two bolts that are just below the seat belt retractor assembly? Mine were in but not holding anything down. Maybe a different type of seat belt attached there? Thanks! George

Has anyone matched the paint on a Warn winch? I need to clean up and re-paint my Warn XD-9000i. Thanks! George

In 1998, we went to this event coordinated by Mark Werkmeister. We were there for the 4th of July that year. The fireworks are great there. Sorry for the rough video...it was an 8mm tape I converted to digital and was degrading over time. Are any of you guys in it? Happy 4th of July...

Is anyone here going? July 8-10 I am working on getting Friday off work and may head up. It is in Redmond. That's Randyzzz area. I'll probably be there and in the Bend area Friday and Saturday. I won't have my Scrambler as it is not quite ready yet. This is my build thread...

I'm about ready to install my fenders. Do you guys put any tape or other strip between the tub and fender mounting surface or the grill? Or do you just bolt it all up? I don't recall anything between there when pulling it all off. I have all new bolts. Thanks! George

Well, I've lurked around here for years and you guys have done some incredible builds. I have gained much from reading and observing. Thank you! I am in Year 3 of my complete refresh of my 1982 Scrambler. I have done a lot of work and I'll post below some of the history of my Scrambler and...

Hi all, I am getting my Voodoo Blue Scrambler put back together. The heater and fresh air boxes are all done and mounted. The writeups here were very helpful! There is a rectangular opening in the lower driver side. Is that supposed to remain open or is there some type of cover? It was...

Hello all, I am cleaning up and rebuilding my brake and clutch pedal assembly. On both the clutch and brake pedals there is a thin shim or washer that has slight bends in it. Is that normal? Is this some kind of worn down tension spring? Can new ones be sourced from anywhere? Can I...