Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
I don't know what the under carriage and frame looks, but she doesn't really look ruff. I've never got a jeep that clean, body looks like a typical, desert vehicle (wind and sand wears the paint. Nice find.
Did minor work on the jeep this winter/spring (new radio, install front speakers. Broke down and pulled the hard half top off. Installed stc half top hardware and half top. Been saving it and another stc half top for the last 11 years. Wanted to use on the original ch8 project but broke down...
If you use chalk, don't chalk all 4 sides, chalk the top and 2 sides, leave bottom open. If not you will trap any water that gets in and it will rot out faster. Always leave a way for the water to escape. Grease is better than wax, Rust pores are too large for the wax to bridge and will...
Into the cylinder you would get white smoke and the exhaust would smell like anti-freeze. Into the oil, depending on the amount (example if you lost a quart of coolant into the oil would raise the oil level, like adding a extra quart of oil on a oil change). If you lost a quart of coolant into...
If coolant in the oil, don't drive it or run the motor much. Anti-freeze will destroy the bearings. Contact who did the work on how they want to handle it. If oil level is correct an no water maybe you were lucky and the shop didn't get all the air out of the cooling system.
Wow, I really figured these days they wouldn't allow it to be used. Your right, the wood (stone) is beautiful. I still remember the look 45 years later.
Do they still sell the bears carved out of petrified wood. Got them in the 70's when we make the trip around the country (this is back when you can do something without worrying about destroying something :rotfl:).
Epoxy Primer and top coat. I'm not a fan of por15. But also they use por15 more for rusted metal, not new metal. Also epoxy/paint the inside first (that's where most of the rust forms, once it's there it's hard to kill).
Nice prep. Don't know if your going to weld additional plate or angle to reinforce it. I you don't at least put a piece of 1/4 flat stock ( something like 4" x 4") to reinforce but also to give more surface area to the rubber mount. Place between the rubber mount and tubs mount that your...
I cut one out of a sheet of metal (from a auto body jobber, patch repair) If I remember right used a sheet of carb gasket material to make a gasket for stock vent. Used that to trace out a vent cover in the metal, cut and used the dock protector poles (filled with concrete) to make the gentle...
I tried the epoxy a metal plate on the inside. Didn't like the look, didn't lay flat enough for my liking on the plastic rib (slots). Also worried about the water sitting on the plate (possible leaks). Ended up making a metal plate to cover it.
Put your original upper hose back on. All those 90's slows the coolant. Worst case with the original is a air pocket at the high point of the hose, but it's a nice straight shot. will flow good (especially when you get her on the road on a hot day).
We should get together some time! I think this makes about 13 Scramblers in the area!
Nice area, what's with the hoarding of the cj8's. :rotfl:
Must be nice. I can't remember the last time I've seen a cj8 around me.:drool:
I used urethane epoxy primer. Tape up the openings, fill and slowly rotate in all directions. Hits all spots and leaks out the seams. Like better than the frame sealer which can cover (bridge over) the seams of the frame. Good epoxy is good protection from water and can also be coated with...
It would make sense that stock would work since it has to go through the hole of the backing plate. This info came from alloy usa (unfortunately omix is the same manufacture. I checked because I wanted to make sure the inter seal (metal housing) is the same as what they use because of the...
Is it leaking at the rear (rear brake line screws into a adapter fitting) or the front button. If either the o-ring seals are leaking. Been told it can be fixed but the process of taking apart and putting together tears the o-ring. If this is your problem, contact inline tube. Finding a new...
Seal should fit. Do you have the original seal. Compare the two. I Just had to replace the inter seal on the alloy usa one piece that I have. They used stock seals (inter and outer). Here's some pics, don't know if it shows enough. You can see the seal fits in the backing plate in the one pic.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.