Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
Trust-
The one I used came out of an early 2000's GMC. Airtex makes a replacement assembly you can buy new if you want. It looks like this:
I took the float and arm off and only use this for the pump and return/accumulator. The stock gauge sender still tells how much fuel is in the tank.
I can offer some further insight, I just did this on a drivetrain swap.
The stock pick up doesn't reach straight down. It bends part way to bottom of tank and reaches toward center of tank. This puts the pick-up sock end into a little molded in sump in the bottom of the tank (1/2 inch deep...
The "nutter" mod does not bypass the ignition box, it bypasses the ECM in 83 and later jeeps that used the BBD carb. The ECM also controlled some relays and vacuum solenoids for one thing or another (I would have to look at wiring diagram again..).
If you already have a weber, re-routed your...
Yes, they were available as an accessory at AMC dealers. They had different color lids for different upholstery too. I bought one from the dealer to put in a used cj7 with a levi's blue lid.
Since it happens when you change speed, I will bet on the rear yoke tabs and that extra space. I had a wrangler in college where one of the spring clips came loose, the bearing cap slipped out a little and that is how it acted.
You could try a shim to see if the joint is shifting between the...
Thanks wm.
Thought I would come back and update this for posterity sake.
I sold them in two days for $2k. And I had more than one taker in line before they were picked up.
I had already listed them on craigslist before I saw your response.
Apparently folks in my area are looking for these...
What would you guys say a rebuilt 258 (1000-ish miles and all accessories still on engine) with re-surfaced flywheel, new clutch and rebuilt (not sure on mileage but works well with no leaks) t5 attached would be worth?
I have done a v8 swap and need some shop space....
Thanks
I don't see the latches in your pictures, only the hinges? With a chrome spacer my hinges don't have.
I have seen the spacers on a cj7. So maybe they are to make space for a tailgate gasket?
Wave washers didn't work on mine with lined interior. I twisted the latch slightly, and made a spacer to...
I used a Crown sender as well. I asked on other sites, was told they are not much different. Don't know about the Speedhut
The brass float is cheaper here, and snapped right in: http://www.summitracing.com/parts/SDK-C0AZ-9202-B/
I made a new strap from thin flat-stock I bent on the edge of my...
I am curious to see how the B&M works for you. I am almost to the point of needing a shifter for a nv3550 I am using behind a ford 5.0 I am putting in. There is a company called Core that makes a short throw too.
Well.. Maybe. Jim tells us the shaft pilot is same so that is good.
You could search and see if someone makes a clutch disk with the correct spline count and diameter hub to match your input shaft, and has correct OD to fit in your pressure plate. Don't forget to check hub offset measurements...
Adding a cross member and center-ish mounting can be a good way to run a longer shock and slightly increase flexibility off road. The point of this mod started as an easier way to keep your shocks from acting like an early bumpstop on axle compression or a limiting strap for suspension drop...
You could do a gm 4.3 v6 or a 305/350 v8. Need 10.5" clutch set and small flywheel (150-something teeth instead of 160-something) to use iron duke bellhousing. Motor mounts are available for either engine
It is not a huge weight savings, maybe 8-10 lbs. But you will get an extra 20+% in deflective resistance strength plus tapered bearings, stronger attachment points and potential of larger fluid reservoir depending on housing shape you choose.
I suggested plastic race seats as they will likely...
What Randy said... Build thoroughness or parts used or program issue.
If never changed the original program may think you are running as high as 3.42 gears with 31 inch tires. That would be hard on torque converter over time if you don't dissipate enough heat.
The sheet metal 9" is lighter, stronger and will gain you over 1inch ground clearance.
Lose dash pad, dash panel. And mount gauges in plastic shhet screwed to a single small cross tube in place of solid panel.
Lose back glass in hard top. Strip floor to bare metal. Lose the upholstered, foam...
Cheapest route is almost alwasy to fix what is in there unless it has major obivous problems. Changing to a new power-plant adds a list of little things that add up in terms of time/money that are hard to figure up front exactly.
But your description, "a bad miss" is kind of vague.... That...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.