• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Search results

  1. M

    258 rebuild

    Better to disconnect (block) the vacuum pipe to the vacuum actuator on the filter body. Doubt if you need a warm air intake unless you drive in the depths of winter. There should be two actuators, one that shuts off the intake when the engine stops and one for the warm air - make sure you...
  2. M

    Where to purchase CJ8 Tailgate rubber bumpstops?

    Hmm - about to say that there aren't any - but the PL shows them, i don't know where they would fit though as the seal takes up all of the usable space. There should be a generic size available - surprised McMaster doesnt have.
  3. M

    AMC 20 Rebuild

    How are you measuring for the shims required? Unless you're lucky the replacement ring and pinion will need different shims. As i recall you have to temporary install the pinion and take some precise measurements to the axle centerline to figure out the shims required.
  4. M

    Door Hinge Mystery

    wished id have bored mine out before i painted them, its also a way to adjust the door fit with careful machining, but i'm sure they dont fit Cj's
  5. M

    82 UK Spec Laredo Scrambler Build No 2

    I like the look of the half doors with no top - gives a cleaner line from the side, but that sure looks nice though. good looking Scrambler. I don't recall ever seeing one in blighty.
  6. M

    Questions about the NOS proportioning valve I bought?

    W may be Weatherford - seem to remember that name from somewhere This site has good info on brake equipment, too bad he didnt have a rebuild kit for mine, but some of the internals are the same as the GM units. https://www.musclecarresearch.com/
  7. M

    Questions about the NOS proportioning valve I bought?

    Would have thought that Alum valves would be subject to galvanic corrosion/too soft , but apparently they exist. Given that possibility there may be no reason that Jeep bought valves from different suppliers to the same spec and that the bodies were different materials. You should be able to buy...
  8. M

    Headlight dimmer switch and carpet!?

    Ar your headlights on a relay? Maybe just a high current demand if not.
  9. M

    CJ8 Picks

    Nice work!
  10. M

    bigwalton's new Jeep: "The Colonel" - 2018 Rubicon Recon JKU

    Looks a bit wobbly up there? Woud'nt be worried about water coming in though
  11. M

    OEM spare tire carrier mounting bolts

    Called Shoulder bolts or Axle bolts try Fastenal or McMaster Carr
  12. M

    Where do you jack up your Jeep

    Had an Austin Mini come off a pair of jacks once, scary, fortunately no-one was underneath and the tyres were on, so no harm except to my nerves. (No i in tyres note). I was wondering about some of the bent stuff on my 8 when i received it, eventually figured out that a PO had it jacked up on...
  13. M

    Jeep Scrambler Alaskan Postal paint code?

    Olympic White Ditlzer 3107 AMC 9B I use paintref.com
  14. M

    Epic fails

    Been there for years?
  15. M

    MDJuan CJ8 delivered

    x2. (or 3) Fit check the doors and the half (or full top) with the bulkhead and windscreen, the door fit is affected by how the tub sits on the frame, so temporarily bolt the tub on. Expect to use a fair mount of Bondo on the rear wheel arches at least. Also chech that all the fiddly bit are...
  16. M

    Back after a long hiatus...have questions about fuel system

    This site is quite good for gm tbi systems or just injection systems on jeeps and IH etc http://www.binderplanet.com/forums/index.php?threads/start-here-fuel-injection-faq-start-here.47254/
  17. M

    Back after a long hiatus...have questions about fuel system

    We pass through Parsons occasionally, pretty area - probably under a foot of snow right now! Which Sniper? https://www.holley.com/products/fuel_systems/fuel_injection/sniper_efi/sniper_efi_bbd_for_jeep_cj/parts/550-858 "what did you have to change on the ignition system? I see lots of those...
  18. M

    Back after a long hiatus...have questions about fuel system

    Nice. I put a Holley Sniper in my 258 - that was a pretty simple install, had to put a new ignition system on it though. Charcoal filter? Bet someone's got one of those - looks like Fleabay is a good bet.
  19. M

    Classic Enterprises panel lip?

    You will need a spot weld cutter and a reasonable scraper you can use to remove the old panels without wrecking the stuff you need The remainder can be got with angle grinder or cutoff wheels, take care on the joints by the exterior panels. You can see where certifiable drilled the welds in post 2.
  20. M

    MDJuan Tubs

    I bought the rear quarter panels ~ 2 years ago. Took a deal of work to fit the RHS - the top bead didn't match on the RHS and needed some judicial welding, the areas around the wheelarch were beaten by one eyed gorillas or something and needed bonus filler. That said it was way better than my...
Back
Top