Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature may not be available in some browsers.
Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.
Better to disconnect (block) the vacuum pipe to the vacuum actuator on the filter body. Doubt if you need a warm air intake unless you drive in the depths of winter.
There should be two actuators, one that shuts off the intake when the engine stops and one for the warm air - make sure you...
Hmm - about to say that there aren't any - but the PL shows them, i don't know where they would fit though as the seal takes up all of the usable space. There should be a generic size available - surprised McMaster doesnt have.
How are you measuring for the shims required? Unless you're lucky the replacement ring and pinion will need different shims.
As i recall you have to temporary install the pinion and take some precise measurements to the axle centerline to figure out the shims required.
I like the look of the half doors with no top - gives a cleaner line from the side, but that sure looks nice though. good looking Scrambler.
I don't recall ever seeing one in blighty.
W may be Weatherford - seem to remember that name from somewhere
This site has good info on brake equipment, too bad he didnt have a rebuild kit for mine, but some of the internals are the same as the GM units.
https://www.musclecarresearch.com/
Would have thought that Alum valves would be subject to galvanic corrosion/too soft , but apparently they exist.
Given that possibility there may be no reason that Jeep bought valves from different suppliers to the same spec and that the bodies were different materials.
You should be able to buy...
Had an Austin Mini come off a pair of jacks once, scary, fortunately no-one was underneath and the tyres were on, so no harm except to my nerves. (No i in tyres note).
I was wondering about some of the bent stuff on my 8 when i received it, eventually figured out that a PO had it jacked up on...
x2. (or 3) Fit check the doors and the half (or full top) with the bulkhead and windscreen, the door fit is affected by how the tub sits on the frame, so temporarily bolt the tub on. Expect to use a fair mount of Bondo on the rear wheel arches at least.
Also chech that all the fiddly bit are...
This site is quite good for gm tbi systems or just injection systems on jeeps and IH etc
http://www.binderplanet.com/forums/index.php?threads/start-here-fuel-injection-faq-start-here.47254/
We pass through Parsons occasionally, pretty area - probably under a foot of snow right now!
Which Sniper? https://www.holley.com/products/fuel_systems/fuel_injection/sniper_efi/sniper_efi_bbd_for_jeep_cj/parts/550-858
"what did you have to change on the ignition system? I see lots of those...
Nice.
I put a Holley Sniper in my 258 - that was a pretty simple install, had to put a new ignition system on it though.
Charcoal filter? Bet someone's got one of those - looks like Fleabay is a good bet.
You will need a spot weld cutter and a reasonable scraper you can use to remove the old panels without wrecking the stuff you need
The remainder can be got with angle grinder or cutoff wheels, take care on the joints by the exterior panels.
You can see where certifiable drilled the welds in post 2.
I bought the rear quarter panels ~ 2 years ago.
Took a deal of work to fit the RHS - the top bead didn't match on the RHS and needed some judicial welding, the areas around the wheelarch were beaten by one eyed gorillas or something and needed bonus filler. That said it was way better than my...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.