1981 scrambler build 3 link

[mike_bfdr]

on fri i had a buddy go pick my crush corners from Poison Spider and i put them on yesterday..............

some time last week when thinking of a cage design for my scrambler that stupid hump on floor always got in the way so i decided to just cut it out and reinforced it and make an access cover for the t-case still need to finish it up.......

 

[dabshr]

Clecos? shooting rivets? lol, looks good!

 

[mike_bfdr]

Clecos? shooting rivets? lol, looks good!

i think im going to use speed nuts, 1/4"-20 but i still need to add to it...........................

 

[Tommy_M]

Nice work. The bumper came out trick.

 

[mike_bfdr]

thanks Tommy..... i try lol

 

[MrBeep]

thanks...... so many views but so little posts lol

You have lots of fans!

Very nice work. Making it your own is a privilage of ownership.

Keep up the good work. Gives us old folks something to look forword to.

 

[mike_bfdr]

LMAO...... thanks MrBeeps....... this is a hobby of mine and just wanted to show everyone....... working at a sheetmetal comp helps lol cause of the laser, cnc pressbrakes, knowing soldworks, autocad, is all a plus

 

[mike_bfdr]

did some work on the inner fender wheel wells only one the driver side...... it took forever lol but the other side shouldnt take that long, oh i still have to clearance around the coil-over still

 

[mike_bfdr]

t-case shifter

 

[Randyzzz]

This is turning out sweet! You're doing a lot of the stuff i wish I'd done on mine....

 

[Tommy_M]

Center console look PIMP! Nice work.

 

[mike_bfdr]

Center console look PIMP! Nice work.

THANKS Tommy to bad im changing it a little................

still have to make the sides and top to hold the shifters

 

[mike_bfdr]

since i move the frame up 3" im going to cut the grill down 3" also....... im going to make a new grill..... made a sample one and had to change it alittle so hope it fits..... pic will come soon......

HOPE A FEW PEOPLE LIKE WHAT IM DOING LOL

covers so i can take the dash off

filler plate for the gas filler

filled some holes

did some trimming

just had to do it

 

[bigwalton]

How the #^$*&%#(*&$(%&^#@ did I miss this thread til now???!!!???

Awesome stuff! Love the rear wheel wells/storage setup! I want and need to redo the wheel wells on mine and want to do them narrower like you did to match the wider axle. Going to need a better rear seat solution pretty soon anyway now that my daughter is getting much bigger.

Love the console and dash too, very sweet!

 

[mike_bfdr]

How the #^$*&%#(*&$(%&^#@ did I miss this thread til now???!!!???

Awesome stuff! Love the rear wheel wells/storage setup! I want and need to redo the wheel wells on mine and want to do them narrower like you did to match the wider axle. Going to need a better rear seat solution pretty soon anyway now that my daughter is getting much bigger.

Love the console and dash too, very sweet!

LMAO LOL THANKS its been alot of hard work and sweet on this jeep.......... i took out about 3 1/2" from each wheel well so i can fit a 42" bench seat back there....... i believe its 43" from wheel well to wheel well..... my son is just 4 months so ill be a while b4 he goes out with me........ the seat will be bolted to the floor and i might just get a small seat for him when he gets alittle bigger...... im running full width axles so i hope ill never get near the wheel wells lol

 

[Randyzzz]

Your new console idea is pretty slick. I might have to do a bit of copying....I miss having the open area between the seats...

 

[mike_bfdr]

A few days ago I cut out my grill for the scrambler..... Let's just say holy poop...... It came out bad *** lol..... I but the grill together and on the jeep and ill post pics soon lol its looking good

 

[mike_bfdr]

still dont quite like it..... i might have to do another grill but 1 inch shorter...... well see lol
if you like it cool.....

 

[Bad Karma]

Is that just plasma table cut? I like it but I think what you are questioning is the turn signal size.

 

[mike_bfdr]

Is that just pliasma table cut? I like it but I think what you are questioning is the turn signal size.

It's was cut on a laser at work..... My buddy has a plasma table but ever since I can use the laser I use it as much as I can...... The size of the turn single is good size but the space between the winch plate and the bottom of the grill is what I don't like but if I shorten the grill then everything will look funny......