• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

8274 projects

wm69

Scrambler Junkie
Silver Member
Lifetime Member
City
God's Country
State
AR
Picked these two up yesterday for $400. Seller says he has the remotes and the solenoid pack off the one that is missing solenoids, but he's not sure where they are. Even so, they are otherwise complete and the housings look solid (I have another SE 8274 with a cracked upper housing that I've been working on for awhile).

Since I already have an X8000i on one Jeep that works fine, I can take my time and disassemble, clean, reassemble these two and make them pretty before installing them.

What is a good used X8000i worth these days? Mine works great, and it's on my "town" Jeep so it probably hasn't been used but 4-5 times. I know it's kind of a regional thing, but figure once I get an 8274 redone I will sell the X winch.
 

Attachments

  • winch2.jpg
    winch2.jpg
    296.9 KB · Views: 233
  • winch.jpg
    winch.jpg
    305 KB · Views: 233
subscribed.....

Not sure on the X8000i. Post pics, I'm sure some folks will chime in. Is it similar to the XD9000i ?
 
subscribed.....

Not sure on the X8000i. Post pics, I'm sure some folks will chime in. Is it similar to the XD9000i ?

Yep, same thing, just 8000lbs instead of 9K.

This will be a SLOW project, since I have two kids and a financee vying for my attention at all times. So far I've taken the top housing off of the "parts" winch and found that the two bolts holding the motor onto the housing are seized, so it's getting a good soak in PB Blaster.
 
OK, used one of the top housings on the 8274 I bought last year (top housing was cracked) and got that one running.

The other two are currently at this stage.


I am going to clean them up, put new lower seals in, have one good prestolite motor with solenoid pack, and I have an extra 4.6 motor from my X8000i and the plan now is to see if I can use it and a contactor instead of solenoids on the other winch. Should have one going pretty quickly, but the other one is going to have some experimenting done on it.

Now, as far as cleaning these up. I would like to REALLY clean them up. I scrubbed on the top housing with some fine steel wool trying to clean it up and that didn't seem to get it like I want it. Has anyone used a media blaster on these? I'd really like to have the housings (top, bottom, and spool end) cleaned up like new, and then clear coat them. I just don't see any way to get down in those ribs on the lower gear housings and the spool end without chemicals or a media blaster.

Spools will be painted black, and motors will too. Going to get some custom aluminum solenoid housings like I have on my current 8274.
 

Attachments

  • IMG_5372.jpg
    IMG_5372.jpg
    291.3 KB · Views: 131
is there an instruction manual on how to tear down an 8274? I need to take mine apart, clutch is not disengaging.
 
I just used the factory exploded parts diagram to take mine apart. When I ran into something I couldn't figure out, I looked it up on the web. Probably not the most efficient way to do things but it worked for me.
 
This is a very good one: http://www.pirate4x4.com/tech/billavista/8274/

And there are also a couple of good youtube videos. Be warned, though, disassembly/reassembly is not quite as easy as they make it out to be. One item that is invaluable is a gear puller you can rent from the parts chains. REALLY helps when you're trying to pull the brake disc off of the housing. To replace, a socket just a tad oversized is a good option to hammer the brake back onto the shaft. An extra set of hands is also very helpful - those things are friggen' heavy!
 
This is a very good one: http://www.pirate4x4.com/tech/billavista/8274/

And there are also a couple of good youtube videos. Be warned, though, disassembly/reassembly is not quite as easy as they make it out to be. One item that is invaluable is a gear puller you can rent from the parts chains. REALLY helps when you're trying to pull the brake disc off of the housing. To replace, a socket just a tad oversized is a good option to hammer the brake back onto the shaft. An extra set of hands is also very helpful - those things are friggen' heavy!

Easy way to get the brake off is a couple of wooden triangles. Drive them down between the housing and brake and it will drop right off. Just make sure you have the retainer plate in the right place.
 
Thread resurrection.

Finally got one of these two on the green CJ and hooked it up. Apparently overtightened one of the motor wires and busted the plastic insulator inside the motor, so had a dead motor when I first tried it.

Swapped a different motor on yesterday, and it works GREAT with the freespool knob out. With the freespool knob in it turns both ways, but is slow and act's like it's dragging.

Have 30W oil in the case, and gears seem to turn fairly smoothly. Wondering if the brake might be hanging up a bit.

Any advice on troubleshooting this thing?
 
I said I would post pics! No need to remind me every two or three years! I said I'd do it!

I looked at the brake this morning. Pretty sure that's the culprit. Looks like I'll be pulling it back off the Jeep.
 
If you have a bad solenoid it will cause the motor to run slow under load. All 4 need to be 100% for the motor to run full speed/torque.
 
Hmmmm. I don't even have a cable on the drum now, and the motor is a fresh rebuild (which I know don't always work well).

All the solenoids click.

I didn't take the brake apart on this one; removed it in one piece and put it back on in one piece. The inner and outer brake disks should have a little movement in them, right? I can't move them a CM in either direction.
 
Yeah, but that shouldn't impede movement. The brake discs and ratchet wheel will just spin and click as it skips over the pawl. (The sliding gear on the brake shaft does stick and renders the brake inoperative...) A locked up brake would only slow/stop movement in the "spool out" function, that is where the brake pawl stops the rachet wheel from turning. You can check if that's the issue by removing the pawl, it's tricky but not impossible to reinstall it with the spring loading- so pay close attention to how it comes off.

Just because a solenoid clicks doesn't mean it's flowing current.
 
Good point. Guess I'll need to make sure they're all flowing correctly.
 
Looks like I might also need to make sure the drum supports are lined up/ not binding.

The motor absolutely hums like a champ with the freespool knob out, so to me it looks more like something binding/bogging that a voltage issue, but I'll double check and report back.
 
Hmmmm. I don't even have a cable on the drum now, and the motor is a fresh rebuild (which I know don't always work well).

All the solenoids click.

I didn't take the brake apart on this one; removed it in one piece and put it back on in one piece. The inner and outer brake disks should have a little movement in them, right? I can't move them a CM in either direction.

LOLOL That sounds like me, Mines been mounted and working for almost two years but I have yet to fill up the drum with wire or rope. I get some goofy looks when folks check out the jeep and they get to the winch. HUHHHH??
 
Back
Top