• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Alternatives to the 258 carbureted engine

cjones

Basic User
City
Waco
State
TX
I know this is heresy to some, but I am not a huge fan of the 258 carbureted engine. Does anyone have experience with adding the fuel injection kit?

Also, what other engine options do I have. I have heard the 350 Chevy engine is one option. Does it work? Are there other options?
 
5.7 liter chevy vortec efi....its easy and you triple your hp...and nearly double your feul economy...
 
I have run several carbed 258's and really don't want another since being spoiled w/ V-8's.

I have recently had a Chevy Vortec 350 (w/ carb) and now an AMC 360. I'd have either before another 6 for what I do. Lots of miles, no offroad. I'd like to run a fuel injected 350 but haven't the knowledge to do it cost effectively w/ performance mods.

I am too low tech :(

Rudy
 
Tbi

cjones said:
I know this is heresy to some, but I am not a huge fan of the 258 carbureted engine. Does anyone have experience with adding the fuel injection kit?

Also, what other engine options do I have. I have heard the 350 Chevy engine is one option. Does it work? Are there other options?

You can purchase a Holley Projection System or a Howell Projection System. I have had the Holley on my 258 for almost 8 years now. It's been "okay". There are pros and cons to it. Howell's system has some advantages. I'm going with a 360 in a few weeks and i am buying a Howell for it.
 
258 (4.2) even with the Carter isnt to bad with the right gears. Even with the 2.73 my 82 gets around fine.

Options I would take include:

- On the cheap 4.0L stock (my choice)
- For the bucks 4.XL stroker which is a 4.0L with a 4.2 crank, awesome torque

I wouldnt go V8 for several reasons including the increasing prevelence of emissions standards throughout the nation that may give you headaches later. Plus the fuel injected 4.0L is about as straight forward of a swap as there is.
 
propane the old 258.......poor man's fuel injection... full kits are about $700 ???

but would love to put a 4.7 stroker into mine lol (4.0 w/ mods)
 
Won't the fuel-injected 4.0 heads fit on the 258 block? Maybe you could find the head and necessary parts in a junk yard.
 
I'm in the midst of a similar dilema, I have a perfectly good 258 (80 k miles) with a fully functioning carb, decent economy (~18 on the highway), the only problem is highway power. I am trying to decide between efi for the 258, a 4.0, a 360 to keep it jeep, or going to the dark side and doing a chev/ford transplant. Mopar is x2 or x3 the Howell, which is x1.5 - x2 the Holley, the swaps all depend on a variety of if/thens to determine the cost but none will be any cheaper than the Howell and none will be any easier. None are ideal for me and thus I haven't decided (well, that and no money). I'll be very interested in which way you go and the rationale.
 
mtruckstuff said:
I think a Blown 3L "Iron Duke" would be pretty cool! :D :D

Just because you're doing it doesn't make it a good idea Paul...


;)


My vote is a 4.0/AW4 combo with one of these!!!
 
trust said:
I'm in the midst of a similar dilema, I have a perfectly good 258 (80 k miles) with a fully functioning carb, decent economy (~18 on the highway), the only problem is highway power. I am trying to decide between efi for the 258, a 4.0, a 360 to keep it jeep, or going to the dark side and doing a chev/ford transplant. Mopar is x2 or x3 the Howell, which is x1.5 - x2 the Holley, the swaps all depend on a variety of if/thens to determine the cost but none will be any cheaper than the Howell and none will be any easier. None are ideal for me and thus I haven't decided (well, that and no money). I'll be very interested in which way you go and the rationale.

Sounds like you are the perfect canidate for a 4.0l HO head swap. Should be good for another 40 hp and pretty much bolt on. Best thing is that you can keep the carb and current set up. All you need beside the head is a 4.0 exhaust header. You can go FI from there, but the head swap should help in making up the missing highway HP.

Carl
 
I opted for the 4.0 head with a junkyard TBI and have been very pleased with it.
I have about $200 in the head/valve cover/exhaust manifold, that's including having the head gone through.
I have about $800 in the TBI but could have been done for about $500 and have EFI with computer controlled timing which the other TBI setups do not offer to my knowledge. And much cheaper than the mopar EFI kit.

Had finally gotten it off road at Tellico a couple of weekends ago and it worked out great far better than the carb.
On the hwy I can cruse at 60/65 with no problem and have plenty of power for acceleration.
 
I've thought about that Carl, in fact a buddy is doing that now on a rebuilt short block. I hate to wrench on stuff these days and moreover I'm very leery of mixing and matching parts when I don't know for sure, 1st hand, what the outcome will be. Most of my wheeling is long, backcountry exploration type trips, so as close to stock, even if it's a different stock is usually better, and I can do 60-65 steadily now if it's fairly flat terrain. Last year one trip was 700 miles each way to the trail head and 4-500 off pavement, a tow vehicle and trailer weren't an option if a cobble together failed. I really don't want to ruin this jeep too (I've been known as the detroyer of jeeps) which is the only reason I'd consider the 'off brand' mills, they've been done to death and are pretty well proven. I may have to keep my eyes open for a head though next time I'm in the pull apart, it wouldn't be a terrible job.

tr
 
Last edited:
bigwalton said:
Just because you're doing it doesn't make it a good idea Paul...;)

I resemble that remark!!!!;)

Aw Eric, you know I'm not actually doing it. I just think it would be cool to beat V8's with a four banger, that's all.:eek:

Actually, my brother is planning on turboing an F-head 134 in his M38A1 Jeep. Plans on using the turbo out of one of those 4cyl SVO Mustangs. Just to do it, ya' know!

I DO have a 4.0 with 1000 miles on it that I plan to stroke and put in the Cherokee, if the original 4.0 with 187,000 miles would ever die, it's still really strong. As it stands, it looks as if I may have to put a clutch in before that time comes.

As for Stroking 258's and 4.0's go to this website for some ineresting info...

http://www.geocities.com/JeepI6Power/

Paul
 
They had a couple of GM 4 banger powered dragster's at Va motor sports park last weekend,that ran the quater mile in 8.6 seconds at 160 MPH or so.
 
Ted Wendel said:
They had a couple of GM 4 banger powered dragster's at Va motor sports park last weekend,that ran the quater mile in 8.6 seconds at 160 MPH or so.

There you go Eric! They also used them in Midgets and race boats. Plenty of performance parts out there. Early units used the same pieces as 283 V8's, except only half as many.
Paul
 
Ahhh...memories of the Pontiac 200 cid+ 4 cylinders of the '60's. They were really half of the V-8 of the time.
 
cjones said:
I know this is heresy to some, but I am not a huge fan of the 258 carbureted engine. Does anyone have experience with adding the fuel injection kit?

Also, what other engine options do I have. I have heard the 350 Chevy engine is one option. Does it work? Are there other options?
I have a 99 4.0l and aw4 in my 83 jeep.Go to http://www.bustedjeep.com
 
What is involved in swapping a 4.0 in place of the original 258? Will the 4.0 motor mounts bolt straight into the CJ, the 258 mounts straight to the 4.0 or does it require custom mounts?
 
Ted Wendel said:
They had a couple of GM 4 banger powered dragster's at Va motor sports park last weekend,that ran the quater mile in 8.6 seconds at 160 MPH or so.

I'll bet those would be fun motors to manage offroad. Not.
 
Back
Top