• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Axle / Axle Gearing Question

hefavitzen

Scrambler Junkie
BENEFACTOR
Gold Member
Lifetime Member
City
Rock Hill
State
SC
Hey folks, I need some advise and input on axle gearing. See, I am looking at some wider axles just to get a little more stability. I have to use spacers today to fit my 32's under the Scram, so I'd like to go wider. But, I am a little inexperienced in this area:

My concerns:
1) Gearing so that my engine is running at too high an RPM for the normal conditions under which I drive the Jeep.
2) Buying axles that are just too damn big and heavy for the conditions under which I normally drive my Jeep.

Those two points are specifically pointing out "the conditions under which I drive my Jeep" because those conditions are 99% on the street. I drive from Rock Hill to Charlotte as often as possible in it and 10 of the 16 miles in each direction is on a highway moving between 60 and 80 mph. These are the conditions under which I drive my Jeep. One day, maybe I'll get to go off road, but I usually just go to work and the hardware store in it.

So, my setup:

I have a Chevy 383 freshly rebuilt and a TH350 transmission that works fine. I plan on keeping both until each component dies and then I'll go new 5.3 and a 4LE60 (whatever).
I currently have narrow track stock axles but they are one piece axles with a 2.73 gearing.

My gearing question: What is a good RPM for highway speed for a Chevy 350/383? Under 3000 RPM seems to be what I read on the Interwebs. So, keeping that in mind: here are my stats according to http://www.grimmjeeper.com/gears.html

Here are those calculations as I could not figure out how to just post the table here

Second issues is size of axles - I have a few offers:
1) Set of 1986 axles - Dana 44 / Dana 30 wide tracks from a CJ with 3.54 gears
2) Set of Dana 44's (front from a Scout) that are set up for a CJ, but 3 inches wider than stock "wide track" with 4.11 gears
3) Set of Dana 44 / Chevy 12 bolt with 3.07 gears also wider than stock "wide track" and will require hangers on the front to be outboarded
4) Set of 14 bolt / Dana 60 that need to be rebuilt for $1000

Not sure which way to go to be honest. Ever have to many options?

Anyone have any opinions or ideas? Thanks, Jeff
 
I would chose option 1. Easier to install and all stock. No guessing which replacement replacement parts you will need. Gearing should be fine also with your engine/tranny setup.

Options 3 and 4 will require alot of work and some more money.
Option 2, do you know for a fact everything was done right? Spring perches set for you lift? Caster corrected?

Sent from my SM-J320P
 
$1500 sound like a reasonable price for a working set?

Sent from my SAMSUNG-SM-G920A
 
I am just completing my own 5.3 with a 4L60E in my Scrambler and I am sticking with the AMC axle with 2:73 gears. 1st is the AMC has a larger and stronger ring and pinion than the Dana 44.. Just so happens I checked the RPMs today and at 65 miles MPH I was turning around 1800 RPMs. Now I only have 14 miles on the set up so there is still a lot to learn. My point is that for a street queen the AMC has advantages over the D44. I will be the first to admit that with 3:83 gears it would have much more launching power but the Jeep was designed for a 110 Hp engine and my 5.3 is at about 330. Either way you will love the set up. PS...I'm running 30" tires, if you go bigger you will want to change the gears too.
 
Last edited:
$1500 if for option 1 sounds high where I live, price could depend on location. That is if they ate stock pull outs. If they have been rebuilt and have a locker of some kind (other than a lunchbox locker), price is not horrible. Last year I sold a '86 CJ dana 44 for $500. It was a stock pullout, stock front widetrac 30's do not sell for but a couple hundred in good usable shape. I paid $1100 for a front 30 with ARB, 4.56, JKS f1 steering, warn hub conversion. $1500 for a front Currie built 44 with ARB and $600 for the matching stock '86 44 rear with an ARB. Bought a complete running '86 CJ7 with a 44 in it for $1100. All this was 15 years ago but prices have not come down any.

Sent from my SM-J320P
 
I been searching for a cj rear 44 also and it looks like everyone want 500 for them. Not sure if there selling at that price but that the asking price in the ny nj area.

Sent from my SM-N910P
 
I have a 350 with a 4 speed that has the same 1:1 final drive as you and 3.54 gears on 33 inch tires. I am usually around 2700-2800 rpm on the highway. It has plenty of get up and go as well.
 
Around here a rebuilt Scout ll 44 will go for around $1200.00.
I have two perfect axles from a Scout, positraction rear end with limited slip front, both with 4:56 gears. Truck is still too good though.
 

Attachments

  • IMG_1117.JPG
    IMG_1117.JPG
    718.2 KB · Views: 57
Last edited:
Dennis, Love that Scout!

As far as axles, option 1 sounds about right with the Th350

With a 4L60E, 4.11 gears would be nice...
 
Back
Top