- City
- Rock Hill
- State
- SC
Hey folks, I need some advise and input on axle gearing. See, I am looking at some wider axles just to get a little more stability. I have to use spacers today to fit my 32's under the Scram, so I'd like to go wider. But, I am a little inexperienced in this area:
My concerns:
1) Gearing so that my engine is running at too high an RPM for the normal conditions under which I drive the Jeep.
2) Buying axles that are just too damn big and heavy for the conditions under which I normally drive my Jeep.
Those two points are specifically pointing out "the conditions under which I drive my Jeep" because those conditions are 99% on the street. I drive from Rock Hill to Charlotte as often as possible in it and 10 of the 16 miles in each direction is on a highway moving between 60 and 80 mph. These are the conditions under which I drive my Jeep. One day, maybe I'll get to go off road, but I usually just go to work and the hardware store in it.
So, my setup:
I have a Chevy 383 freshly rebuilt and a TH350 transmission that works fine. I plan on keeping both until each component dies and then I'll go new 5.3 and a 4LE60 (whatever).
I currently have narrow track stock axles but they are one piece axles with a 2.73 gearing.
My gearing question: What is a good RPM for highway speed for a Chevy 350/383? Under 3000 RPM seems to be what I read on the Interwebs. So, keeping that in mind: here are my stats according to http://www.grimmjeeper.com/gears.html
Here are those calculations as I could not figure out how to just post the table here
Second issues is size of axles - I have a few offers:
1) Set of 1986 axles - Dana 44 / Dana 30 wide tracks from a CJ with 3.54 gears
2) Set of Dana 44's (front from a Scout) that are set up for a CJ, but 3 inches wider than stock "wide track" with 4.11 gears
3) Set of Dana 44 / Chevy 12 bolt with 3.07 gears also wider than stock "wide track" and will require hangers on the front to be outboarded
4) Set of 14 bolt / Dana 60 that need to be rebuilt for $1000
Not sure which way to go to be honest. Ever have to many options?
Anyone have any opinions or ideas? Thanks, Jeff
My concerns:
1) Gearing so that my engine is running at too high an RPM for the normal conditions under which I drive the Jeep.
2) Buying axles that are just too damn big and heavy for the conditions under which I normally drive my Jeep.
Those two points are specifically pointing out "the conditions under which I drive my Jeep" because those conditions are 99% on the street. I drive from Rock Hill to Charlotte as often as possible in it and 10 of the 16 miles in each direction is on a highway moving between 60 and 80 mph. These are the conditions under which I drive my Jeep. One day, maybe I'll get to go off road, but I usually just go to work and the hardware store in it.
So, my setup:
I have a Chevy 383 freshly rebuilt and a TH350 transmission that works fine. I plan on keeping both until each component dies and then I'll go new 5.3 and a 4LE60 (whatever).
I currently have narrow track stock axles but they are one piece axles with a 2.73 gearing.
My gearing question: What is a good RPM for highway speed for a Chevy 350/383? Under 3000 RPM seems to be what I read on the Interwebs. So, keeping that in mind: here are my stats according to http://www.grimmjeeper.com/gears.html
Here are those calculations as I could not figure out how to just post the table here
Second issues is size of axles - I have a few offers:
1) Set of 1986 axles - Dana 44 / Dana 30 wide tracks from a CJ with 3.54 gears
2) Set of Dana 44's (front from a Scout) that are set up for a CJ, but 3 inches wider than stock "wide track" with 4.11 gears
3) Set of Dana 44 / Chevy 12 bolt with 3.07 gears also wider than stock "wide track" and will require hangers on the front to be outboarded
4) Set of 14 bolt / Dana 60 that need to be rebuilt for $1000
Not sure which way to go to be honest. Ever have to many options?
Anyone have any opinions or ideas? Thanks, Jeff
