- City
- Richmond
- State
- VA
Well here is the short version, upgrading axles on Goose, my 69 Commando trail rig. It currently has a narrowed WT FSJ Dana 44 SOA in front and FSJ centered 44 in back geared 3.73 and both have Powerlocks. I run heavy military Michelin XZL 39" tires and am on borrowed time with the Dana 44's. Don't want to wait until I break something because I will swap these axles under my Scrambler.
I am upgrading the front to a narrowed GM Dana 60 with 35 spline inner and outter shafts with a E-locker and 4.56 gears (do not want to outboard springs to run full width). My front 60 is already geared 4.56 and has high steer, also, I have two spare sets of 4.56 gears for a Dana 60. It is the rear axle I am undecided on and looking for some advice. I have several possible candidates on hand and they are outlined below:
Dana 60-2: Stock setup with 4.10 gears. Case is damaged from carrier internals exploding (not me) but fixable. Shafts are massive band would need rebuild and disc brake conversion. Would also narrow one side to center pinion and get WMS/WMS to around 62". Would need the 4.56 gear change and some type of locker (have a RichmondII could use).
Ford Dana 60 FF: Picked this up a few years back. It is 4.10 with Lincoln locker. WMS/WMS is 66" but I have Dodge aluminum rims with 6.5" BS (this is older Ford rear so same bolt pattern as Dodge). Could run as is until it breaks then upgrade to 1.5" shafts. Could use one of my spare 4.56 gear set and Richmond locker with new shafts.
14 Bolt #1: 4.56 with Detroit locker. Currently still has massive drum brakes but 14 bolt #2 below has been converted to disc so could swap them over. 67" WMS/WMS.
14 bolt #2: 4:56 gears with Richmond locker and as stated above it has disc brakes. Also, 67" WMS/WMS.
First, remember this is a Commando so frame is comparable to a Scrambler (meaning light). The 14 bolts seem over kill to me and I know they hang low. I should add that I am considering modifying the hubs to stay 6 on 5.5" so I don't have to buy new wheels and have the tires moved. The 60-2 could easily be redrilled to this lug pattern, not sure about the Ford. 6 lug hubs are available for the 14 bolt but they are major bucks.
Ssssoooooooooo... Opinions, advice, experiences, etc, please! I only want to do this once and I have no experience with either rear 60's or 14 bolts in a trail rig.

Richard
I am upgrading the front to a narrowed GM Dana 60 with 35 spline inner and outter shafts with a E-locker and 4.56 gears (do not want to outboard springs to run full width). My front 60 is already geared 4.56 and has high steer, also, I have two spare sets of 4.56 gears for a Dana 60. It is the rear axle I am undecided on and looking for some advice. I have several possible candidates on hand and they are outlined below:
Dana 60-2: Stock setup with 4.10 gears. Case is damaged from carrier internals exploding (not me) but fixable. Shafts are massive band would need rebuild and disc brake conversion. Would also narrow one side to center pinion and get WMS/WMS to around 62". Would need the 4.56 gear change and some type of locker (have a RichmondII could use).
Ford Dana 60 FF: Picked this up a few years back. It is 4.10 with Lincoln locker. WMS/WMS is 66" but I have Dodge aluminum rims with 6.5" BS (this is older Ford rear so same bolt pattern as Dodge). Could run as is until it breaks then upgrade to 1.5" shafts. Could use one of my spare 4.56 gear set and Richmond locker with new shafts.
14 Bolt #1: 4.56 with Detroit locker. Currently still has massive drum brakes but 14 bolt #2 below has been converted to disc so could swap them over. 67" WMS/WMS.
14 bolt #2: 4:56 gears with Richmond locker and as stated above it has disc brakes. Also, 67" WMS/WMS.
First, remember this is a Commando so frame is comparable to a Scrambler (meaning light). The 14 bolts seem over kill to me and I know they hang low. I should add that I am considering modifying the hubs to stay 6 on 5.5" so I don't have to buy new wheels and have the tires moved. The 60-2 could easily be redrilled to this lug pattern, not sure about the Ford. 6 lug hubs are available for the 14 bolt but they are major bucks.
Ssssoooooooooo... Opinions, advice, experiences, etc, please! I only want to do this once and I have no experience with either rear 60's or 14 bolts in a trail rig.

Richard

