• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

First scrambler build!

What the heck. I deleted like 20 messages. Still says full

I have been trying a couple times and still says full. If it doesn't work in the morning I recall I have your email address as well. Its just buried in my email :rolleyes:
 
If you can get NOS even if it's $125 it'll be way better than far king around with aftermarket garbage. What we have found (and paid dearly for all the way back to west coast Oz) is that the ends of the seal are much more dense rubber and WILL NOT COMPRESS. The amount of load required pulling back on the windscreen frame to get the screw plate done up was making me all "pucker up" fearing a busted screen. I went back to OOS on both our current projects. Hate to be negative, sorry.
 
I have been trying a couple times and still says full. If it doesn't work in the morning I recall I have your email address as well. Its just buried in my email :rolleyes:

Turns out we were trading PMs last year but I never did have your email. Tried again this morning and still full. Try sending me a email by clicking on my very old out of date website - and click "email me" jerseyjeeps dot net.
 
If you can get NOS even if it's $125 it'll be way better than far king around with aftermarket garbage. What we have found (and paid dearly for all the way back to west coast Oz) is that the ends of the seal are much more dense rubber and WILL NOT COMPRESS. The amount of load required pulling back on the windscreen frame to get the screw plate done up was making me all "pucker up" fearing a busted screen. I went back to OOS on both our current projects. Hate to be negative, sorry.

I have not found or ordered the wind shield frame to cowl seal yet. I would love to find a NOS or a good fit aftermarket if anyone comes up with something. Heck cost and common cents left me the day I bought this 8.
 
The supersoft is the one I used on the cj8 build. Fit good except the strip on the outside of the windshield frame. It wouldn't stay against the frame. After leaving it sit for a week I ended up chalking it to the frame (held against frame with tape). It compressed good when I pulled the frame back to the measurement another form member gave me (from top of frame to back edge of tub.
I just ordered the door, tail gate and windshield seals from these guys. They are kinda expensive but phht, what's not? Besides I'm almost 64 yrs old, I'm not spending my money anymore, I'm spending my kids inheritance.
 
So the last thing I've got before my dash goes in are are fuel and temp gauges. I just received the new gauges in the mail today. I know these gauges are very sensitive and can make for an easy screw up. Anything I need to know before I get this in? I do have a new sending unit for fuel but haven't replaced the sending unit for temp yet


 
I've had nothing but bad luck with the stock fuel gauges in the past so on my new build I'm trying the Speedhut gauge cluster. It's shipping out today. I think the stock fuel gauge has a built in voltage regulator that keeps going out. I suspect it could help to run a better ground wire but that's just my guess.
 
So I'm getting ready to finish everything that needs to be done before I bolt on my fenders. I bought a new MC2100 over a year ago from the guy on eBay ( in sure many of you are familiar) I'm wanting to see if I can get a few pictures from you guys running this carb. I'm trying to figure out the throttle linkage.


 
Well it's been a while since I've updated my build thread because not much of anything has been done. I've been so busy with work and life in general the jeep has been on the back burner. Not to mention my 2nd paint and body guy has pretty much quit making any progress. I can't get much else done until the last pieces are painted so I'm kind of at a stand still. I'm seriously debating selling this project and buying another scrambler that's ready to enjoy. I was so hopeful that I would have this jeep done in time to enjoy it this summer but now that won't happen. I need to find someone reliable to help me finish the jeep or just move on.


 
That really sucks. I hope you find a way to get the paint done. Reassembly goes a lot faster.
 
Back
Top