• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Fuel And Temp Gauge (Opening up a Can of Worms)

Griff04

CJ-8 Member
City
Albany
State
Ga
Well I jumped off into my fuel and temp gauge no working. I'm replacing the windshield, already off, so I just unbolted the dash which gave me some room to work. Boy was I surprised, what a mess, the PO had installed a aftermarket radio which doesn't work, made a mess out of the wiring, found some type of small amp, just a dang mess. Along with all that I found the duct missing for the defrost so I know it's not working. So be it, just suck it up and move forward.

Anyway, been reading up on the gauge issues, there's enough info out here on grounding it makes my head hurt. With the dash pulled out I noticed some rust along with a couple grounds just hanging loose. Gonna try and trace all this stuff out and see where it goes. I'm hoping this won't be too painful but it ain't looking good.

Anyone got any advice before I dive into it??

Also I notice a fuse mounted in the dash located just left of the steering wheel, it's one of the bulb style, it's not hooked up, does anyone knows what it is suppose to go to?

Thanks,
Griff04
 
If you can afford it, buy a speedhut speedo and be done with the issues........ It comes with a much better quality temp sensor that is two wire (instead of relying on block grounds).

Pretty sure the next best option (only somewhat cheaper) is looking for NOS guages....

My 2 cents......
 
I'm still trying to identify this glass filament fuse located on the dash just left of the steering wheel??

Thanks,
Griff04
 
Not aware of any of that type fuse used by the factory. Must be add-on.
 
Search eBay for Mopar Part#4740791. This is a factory improved/replacement set of fuel/temp gauges that work perfectly with the stock sending units. I have a pair of these in two different Scramblers, they work flawless, and look stock :twocents::thumbsup:
 
Search eBay for Mopar Part#4740791. This is a factory improved/replacement set of fuel/temp gauges that work perfectly with the stock sending units. I have a pair of these in two different Scramblers, they work flawless, and look stock :twocents::thumbsup:

So I found the gauges on EBay, $175 for both of them, only found one listing. The Seller did have some negative feedback, "selling imitation NOS items", may have to think on that???

Anyway, I had ordered some Crown replacements a few weeks back and put them in today. My old fuel gauge did ohm out bad so hopefully this will fix it. I did do some work on the grounds, ran a ground off the speedo through the firewall to the ground that is running off the battery is located. Also ordered a ground strap for the engine to frame, mine was in pretty bad shape, it should here tomorrow and I'll put it on.

Once that's installed I'll fire her off and see if the Crown units work, if I don't "fry them" them I'll probably look at upgrading them. Will post back tomorrow on the results.

Griff04
 
So I found the gauges on EBay, $175 for both of them, only found one listing. The Seller did have some negative feedback, "selling imitation NOS items", may have to think on that???

Anyway, I had ordered some Crown replacements a few weeks back and put them in today. My old fuel gauge did ohm out bad so hopefully this will fix it. I did do some work on the grounds, ran a ground off the speedo through the firewall to the ground that is running off the battery is located. Also ordered a ground strap for the engine to frame, mine was in pretty bad shape, it should here tomorrow and I'll put it on.

Once that's installed I'll fire her off and see if the Crown units work, if I don't "fry them" them I'll probably look at upgrading them. Will post back tomorrow on the results.

Griff04

They are not NOS gauges, they are improved gauges that were made by Sewart Warner for Mopar/Jeep. The stock gauges use that CRV thingy, these are straight 12 volt gauges :thumbsup:

They look just like the original gauges once installed, but if you put them side by side with stock/NOS gauges uninstalled, they look different. I guess people assumed they are NOS, they are not, they are better :twocents:

If I were you, I would run a ground strap to the back of the dash board, and maybe even a ground wire to the back of the speedometer housing. Good grounding is crucial for the gauges to operate correctly, whatever brand :thumbsup:

No acceptable public comment on the Crown gauges :(:mad:
 
Well installed the new ground strap, still no luck, not working. I did run a new ground off the speedo housing out to the battery. Not sure what my next move is, may order the ones off of EBay. Will go back through all my connections tomorrow. Right now gotta get ready to go to work.

Thanks for all the input.
 
Well installed the new ground strap, still no luck, not working. I did run a new ground off the speedo housing out to the battery. Not sure what my next move is, may order the ones off of EBay. Will go back through all my connections tomorrow. Right now gotta get ready to go to work.

Thanks for all the input.

Hit the "Buy it Now" on EBay for the gauges before leaving for work. Scheduled delivery is next Tuesday, plenty of other things I can be doing on her while I wait for delivery.

Any do's or don'ts on these new style gauges that I need to know about? Don't want to mess them up??

Griff04
 
They are not NOS gauges, they are improved gauges that were made by Sewart Warner for Mopar/Jeep. The stock gauges use that CRV thingy, these are straight 12 volt gauges :thumbsup:

They look just like the original gauges once installed, but if you put them side by side with stock/NOS gauges uninstalled, they look different. I guess people assumed they are NOS, they are not, they are better :twocents:

If I were you, I would run a ground strap to the back of the dash board, and maybe even a ground wire to the back of the speedometer housing. Good grounding is crucial for the gauges to operate correctly, whatever brand :thumbsup:

No acceptable public comment on the Crown gauges :(:mad:

So in regards to wiring for these style 12v gauges what changes will be needed. Hoping they come with instruction.

Griff04
 
So in regards to wiring for these style 12v gauges what changes will be needed. Hoping they come with instruction.

Griff04

Yes, they come with instructions :thumbsup:

IIRC, they hook up using the same three stock wires:

1) The 12v power supply
2) Sending Unit wire for temp gauge
3) Sending Unit wire for fuel gauge

The stock fuel gauge has some type of weird voltage doo hickey, think it is called a CVR, that goes bad and fries the stock gauges. It reduces the 12 volts down to some lower voltage IIRC.

The new gauges use the full 12 volts, and they come with a "jumper strap" to provide the voltage for the temp gauge off the fuel gauge.

Before installing the new gauges, I would make sure all your grounds are good, check the sending units :twocents:

Also, the new gauges each will have these little plug in gound/contact piece. Make sure it makes good contact with the speedometer housing to ensure a good ground.
 
I couldn't find a set of the Mopar gauges when I needed them. Good find, lots of good things said about them.

If you want to check your stock gauges, they can tell you about how/why they failed. May help with what to check in circuit.

If the CVR Spankers is referring to in fuel gauge is bad, that is common. That is your resistance between I and A terminals and should be 0. And if its not, and other resistances in gauge check out, you can bypass the CVR with a $4 electronic voltage regulator and the stock gauges will go back to working like they should.

If the sending unit resistor side is burned up, that is a short in a sender wire or a bad ground in system at your senders. That check is resistance between S and A on fuel gauge and S and A on temp gauge. Should be 20-ish ohms for each.
 
I couldn't find a set of the Mopar gauges when I needed them. Good find, lots of good things said about them.

If you want to check your stock gauges, they can tell you about how/why they failed. May help with what to check in circuit.

If the CVR Spankers is referring to in fuel gauge is bad, that is common. That is your resistance between I and A terminals and should be 0. And if its not, and other resistances in gauge check out, you can bypass the CVR with a $4 electronic voltage regulator and the stock gauges will go back to working like they should.

If the sending unit resistor side is burned up, that is a short in a sender wire or a bad ground in system at your senders. That check is resistance between S and A on fuel gauge and S and A on temp gauge. Should be 20-ish ohms for each.

So I some resistance test based on the following page, see the bottom of the page:
http://civilianjeep.info/Strenk/Gauge web page/WebPageGauges1.htm

Here are the results:

Fuel gauge:
Grd to S 71
Grd to I reads ohm which I'm assuming is zero
Grd to A 51
S to I reads ohm
S to A 21
I to A reads ohm

Temperatur gauge:
Across the 2 post reads 21

So, the readings you mentioned are correct @ 21. The only oddball, called out on the webpage, is "grd to I" which should read 51 but reads ohm or zero.

Not sure what that means so I'm assuming the gauge is bad?

Any input on this appreciated before I burn up the new $175 gauges I bought.

Thx,
Griff
 
Those threads Mr. Strenk has put up on other sites are really good. Here is a second one that has a bit more measuring and testing detail:
http://civilianjeep.info/Strenk/Gauge web page/basic_troubleshooting_for_cj_gau.htm

Those readings suggest you have a bad CVR. Those fail for lots of reasons, you would have to take face off the fuel gauge to know what happened to it.

I think if you make sure your grounds are good, your 12V feed is 12V, and your senders for fuel and temp senders read in correct resistance range you will be happy with new gauges.

Save your old ones though. It may be as easy as sanding contact surfaces on the CVR (bottom left points looking thing in picture below) to have them working again.
jeep cvr.jpg

Or, if something on that whole CVR leg is toast, you can bypass the CVR like this:
https://www.cj-8.com/forum/showthread.php?47267-Fuel-gauge-Voltage-Regulator-BYPASS&highlight=cbford
 
Got the gauges installed, still no go, neither one reading. Installed aftermarket temp and fuel sending units several weeks ago, is it possible that they are bad? Got a ground ran straight off the battery to speedo housing the for troubleshooting purposes so I wouldn't think that would be an issue, maybe the ground on the fuel sending unit itself??? Did notice that my oil pressure gauge quit reading, not sure if it's related or not. Right now I'm gonna take a break from it and clear the head before I BREAK something.

Thanks
Griff
 
Got the gauges installed, still no go, neither one reading. Installed aftermarket temp and fuel sending units several weeks ago, is it possible that they are bad? Got a ground ran straight off the battery to speedo housing the for troubleshooting purposes so I wouldn't think that would be an issue, maybe the ground on the fuel sending unit itself??? Did notice that my oil pressure gauge quit reading, not sure if it's related or not. Right now I'm gonna take a break from it and clear the head before I BREAK something.

Thanks
Griff

Haven't been following this too closely, so forgive me if this is too basic.
The gauges need to have 12 volts to them when in "Ignition/Run" position.
The sending units vary the resistance to the gauges to give the proper indications. The grounds to the sending units are important to their operation.
The fuel sending unit needs a good clean connection to the frame. The oil and temp. sending units need a good clean (no teflon tape) connection to the grounded engine block.
Confirm you have voltage to the gauges, confirm the sending units have good grounds, also confirm your wiring has continuity from the sending units to the gauges.
 
Now I'm really confused, everything appears to be working now. Temp, oil, and fuel gauges are all reading. Actually added a couple of gallons of gas out of a can I had and it registered, let the Jeep idle and the temp gauge came up, oil pressure shot to 50. The only thing I did that I feel would have impacted anything was checking the voltage on back of the fuel gauge and removed the hot wire and put back on. Also checked continuity on the temp sending unit. I don't have a clue but definitely going to leave it alone and see what happens.

Appreciate all the input.
Griff04
 
Everything I ever bought that was Crown or Omix Ada eventually turned to junk.
 
Now I'm really confused, everything appears to be working now. Temp, oil, and fuel gauges are all reading. Actually added a couple of gallons of gas out of a can I had and it registered, let the Jeep idle and the temp gauge came up, oil pressure shot to 50. The only thing I did that I feel would have impacted anything was checking the voltage on back of the fuel gauge and removed the hot wire and put back on. Also checked continuity on the temp sending unit. I don't have a clue but definitely going to leave it alone and see what happens.

Appreciate all the input.
Griff04

I wonder if the 12 volt power wire just didn't have a good connection :shrug: Maybe sand the inside of the 12 volt plug, maybe compress it a bit more so that is has a good contact :shrug:

Everything I ever bought that was Crown or Omix Ada eventually turned to junk.

Yep, unfortunately :angry:
 
Back
Top