• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

I'm now an official scrambler owner

ducktapeguy

CJ-8 Member
BENEFACTOR
Lifetime Member
Member
City
SoCal
State
CA
Hello everyone

Well, looks like I'm finally an official scrambler owner. I had forgotten I had registered on this site over 10 years ago, looks like I finally achieved my goal of getting an AK Postal.

And cuz i know bigwalton loves pictures, here it is

20150919_164429-1.jpg


I'm sure I'll have a lot of questions coming up. Plans are to semi-restore back to original condition. Probably not a true restoration, but more of a resto-mod. First thing i did was pressure wash everything so I could see what I was dealing with. Fortunately, it was in better condition than I expected. Frame rust is almost non-existant, and that's by dry Southwest standards, not the East coast definition. There are a few bad areas of rust on the driver floorpan and wheel wells, but nothing major. I also have a 75 DJ5D (in the background) so I'm somewhat familiar with the 258 drivetrain, but there's a lot more random equipment in the engine bay than in my DJ. Some of it might be stock, but some of it is definitely PO add on.

Couple more pics

20150919_151831-1.jpg


Plug in Hybrid? 2 of the wires go to an inside heater and battery trickle charger. Not sure about the third one yet, but maybe it has something to do with the random switches inside.

20150919_150556-1.jpg

The seats are labeled JEEP, but I don't know if they were stock for this one?

20150919_150701-1.jpg


Most of the insulation is intact, looks like thy started removal but never finished. I'm thinking of keeping it intact and just shave it down smooth and cover it with headliner type material.
 
Nice!
One plug may be for a block heater. Check to see if one if the freeze plugs/expansion plugs has wires going into it.
 
Most of the insulation is intact, looks like thy started removal but never finished. I'm thinking of keeping it intact and just shave it down smooth and cover it with headliner type material.

Congrats! Your foam idea sounds great. I would love to see how you do it! I've heard nightmare stories about removing it. I think a build thread is in order! :popcorn:
 
Welcome back !! :)
Those seats are from a YJ wrangler that say jeep on them , 1990 ish.
 
Took it out for a spin today, drives like crap, but just needs some tuning and TLC. Figured out what the third plug was for, some type of recirculating coolant pump

Located on the left frame rail. I'm assuming this was a coolant warmer. Whoever had this jeep really had it setup for cold temperatures.
20150920_181610-1.jpg


Ripped up the nasty carpeting in the back and was almost scared to find out what's underneath, but to my surprise the floor is perfect. Not even a little bit of pitting, no dents or anything.
20150920_083243-1.jpg


Since I had bought this jeep without ever seeing it, I fully expected the rest of the body to look like what was left of the drivers side floorpan. At least the gaping holes prevented moisture buildup and the support beams are unharmed. I guess the floor sacrificed themselves for the greater good.
20150919_160301-1.jpg


I found another set of mystery plugs on the right fender well. Looks to be added from one of the previous owners, the wires disappear into the wire loom so I haven't had time to trace it
20150919_160048-1.jpg


The jeep also came with a set of fender flares and diamond plate quarter panels in the back, but they're not for this jeep. The front flares are a little too long for the scrambler fenders, the rear just don't have the right shape. Possibly a later model jeep? The rear quarters panels are way too short for the scrambler, so I'm guessing maybe a CJ5? Anyone have any guesses?
20150919_170033-1.jpg
 
Congrats! Your foam idea sounds great. I would love to see how you do it! I've heard nightmare stories about removing it. I think a build thread is in order! :popcorn:

I found another idea that I might do instead of headliner. The rear cargo area of the jeep is pretty dark because of the lack of windows, so I'm thinking of using white Coroplast, that corrugated sign material that they also use in those white mail bins at the post office, to brighten up the interior. I think I could probably epoxy a few threaded inserts in the foam to support, and at the same time run some LED light strips behind it to give a diffuse lighting.

Right now it's probably too early for a build thread. I'm just taking it slow and going over everything to find out what's wrong. My usual plan on new project is

Brakes - Replace all the flexible line with braided stainless. Hard line looks ok, but I have to check
-Inspect and rebuild all the brakes.
- Under to hood there's a note saying DOT5 only. Was this standard on all CJ8's or maybe just the postal?

Steering - Feels fine, but a little light. I'm not sure if that's normal. I'll probably just flush and refill

Suspension - There are some huge rock grabbing lift shackles that I want to replace. I think either the wrong bushing or wrong width shackles are used, the bolts are overtighted and bending the shackles.
20150919_150440-1.jpg


Engine - Probably tear into the engine and the transmission later on. It's running right now, but not very smooth. Right now this scrambler is making my DJ feel like a sports car.
 
Congrats on the postal! Was this the one for sale on Oklahoma City's craigslist a little while back? My advice on the foam, get it all out now! It is a huge pain, probably one of the worst jobs I've ever had to do on my Jeeps, but get it out of there. It just traps moisture and promotes further rusting, especially around the wheel wells.

The foam removal is a right of passage for postal owners. Once the foam is out it will probably expose more rust in areas than you aren't expecting. This has been my experience with two postals. Good luck!


Sent via signal flare
 
Jeep was located in TX, but it could have been on multiple listings. I will have to take the foam off the fenders when I patch it up, but if possible I want to leave it on the hardtop. I'm in CA where don't even get enough rain to grow grass, so rust isn't an issue. It was in the 90's over the weekend and the foam really helps keep the interior cool. Compared to my un-lined dj, the back of the postal almost felt comfortable. I'll have to take some temperature readings for comparison.
 
Congrats!! :woot:

I'm thinking of keeping it intact and just shave it down smooth...

I got a phantom bit of foam in my eye while I was reading that... I do not envy whomever you pay to do that. You aren't talking about doing it yourself, right? :eek: That stuff is pure Satan spawn evil :evil: once it gets in the air, and the word "shave" in reference to it made me more than slightly nauseous.
 
The plugs on the fender are stock diagnostic ports on all the Postals. They run to various T's in the wire loom where they were crimped on. You'll eliminate a crapload of wire in the engine bay by tracing them back and cutting them out.

The dot 5 brake fluid is a Postal thing. Supposedly it absorbs less water than dot 3, which is an issue in the cold of AK. DO NOT put Dot 3 in it unless you've replaced anything with a seal in it (calipers, wheel cylinders, master) Dot 3 will make the seals swell and leak. I switched mine over to dot 3 when I redid the axles and replaced literally everything in the brake system other than the hard lines.

Likely those lift shackles are killing your steering and handling. Definitely dump them whenever you can with a proper-length set. They allow a ton of side-to-side play in the suspension when turning and kill your caster angle, making steering more dodgy.

Flares look like YJ. Scramblers have unique-shaped rear wheel openings and only Scrambler flares fit in the rear. Any CJ-7 flare works in the front.

I wouldn't try to do anything with the foam other than pull it out or (God help you) leave it. When I had the foam in and drove with the windows down, the dust from the foam created the equivalent of a trillion tiny daggers flying through the air, all looking to wedge into my eyeballs. I couldn't get it out fast enough.

I don't see any epoxy holding to the foam, but knock yourself out.

One last tip, check that you have full throw on the throttle linkage when the pedal is on the floor. I drove mine back from AK not realizing I only had 2/3 throttle when it was mashed. I spaced my gas pedal off the firewall 1/2" and was able to go all-out.
 
Hey Eric,

Glad you found this post. I don't remember if i knew about these AK postals from having a DJ5 or from your site, but it was definitely your trip from AK that kicked my obsession into high gear. Couldn't find one ten years ago so I ended up with an FJ40 to occupy my time instead, but the thought of getting an AK postal was always burning in the back of my mind. I wanted to make the same trip down from AK but the reality set in that I probably wouldn't find the time or a postal in good enough condition to drive down. So my plan is to eventually get this one fixed up and drive it back up to Alaska. May not be fore another decade.

I may have to rethink the whole foam idea, I'll have to defer to the more knowledgeable people's experience with it. I haven't driven it enough to know whether it's going to be a problem, I just pressure washed the entire inside and the foam seems to be structurally sound, but that may change. I plan on re-doing the front headliner with coroplast anyway, I may try lining the back and see how it works out. Worst case I have to remove it in the future.

It will be a while before any major changes happen. Right now the first order of business is to get it running safely, then I'll figure out what to do. Definitely want to flush the brake system, I don't know what type of fluid is in there right now so I have no idea whether it's DOT5 or DOT3. May just rebuid everything to be safe.

So what did they plug into those diagnostics port? Some sort of early version of OBDII? I don't want to mess with the wiring harness just yet until I figure out what's working and what's not, but it would be nice to clean up the engine compartment. Even though I've worked on the 232 engine, the 258 just has so much more stuff in it I can barely figure out what is going where.

I'll look for a stock set of shackles too. I did notice that the steering felt a little light, I'm sure the caster angle contributed to that. On a similar note, is the front sway bar standard on scramblers? If you look in the last picture it appears there's a swaybar disconnect, which I can't tell if it's home made or not. How much of these suspension components (and parts in general) are shared with other Jeeps? would shackles from any CJ of similar year work? CJ5 and 7 stuff seem a lot more plentiful.

Funny you mentioned about the throttle linkage. Last night I was looking closely at it because something just didn't feel right. The pedal had almost no travel when stepping on it so I was inspecting it closely to make sure nothing was bent. Looked like everything was normal, so I just thought that's how they were. Now I'm going to have another look and pay attention to the throttle opening. Maybe this was the Post Office version of a speed limiter?

BTW, is there an edit button on this forum? If there is I can't find it.
 
The original postal seat is a gray tweed, and not made with the usual CJ seat frame. Not sure if it was an AMC-spec or something that the USPS required, but it's definitely not a "normal" CJ seat. I've seen the specific seat in too many postals for it to be a random aftermarket coincidence.
 
I plan on re-doing the front headliner with coroplast anyway, I may try lining the back and see how it works out. Worst case I have to remove it in the future.

Pretty sure someone used a pressure washer to remove the foam in theirs, seemed like a good idea to keep the dust down. That #$%@ is just evil. I used fingers and a small prybar and it sucked all holy hell.

So what did they plug into those diagnostics port? Some sort of early version of OBDII? I don't want to mess with the wiring harness just yet until I figure out what's working and what's not, but it would be nice to clean up the engine compartment. Even though I've worked on the 232 engine, the 258 just has so much more stuff in it I can barely figure out what is going where.

Mainly it's for resistance measurements IIRC, I didn't look into it further than to realize I was going to rip all that #*$& out. It's a bit of work to get into it that far, but well worth it IMHO.

On a similar note, is the front sway bar standard on scramblers? If you look in the last picture it appears there's a swaybar disconnect, which I can't tell if it's home made or not. How much of these suspension components (and parts in general) are shared with other Jeeps? would shackles from any CJ of similar year work? CJ5 and 7 stuff seem a lot more plentiful.

Swaybar was standard. Suspension and steering is the same as a wide track CJ-7. Basically, everything in front of the rear wheel wells with the exception of the rollbar and decal/appearance stuff is the same as the -7s.

BTW, is there an edit button on this forum? If there is I can't find it.
There is for paid forum supporters. One of the perks of paid membership. https://www.cj-8.com/forum/payments.php or the link in the top nav. Less than $3 a month. :thumbsup:
 
well I just checked and I am not getting full throttle travel due to the pedal. Still wondering how that could happen because nothing everything seems to be in place. I'll have to space it out as you've said

Is there any way to fold down the windshield without removing the top? I couldn't find any type of attachments to the windshield, but I was working in the dark so I could have easily missed it. I want to remove the dash to clean up behind there, I found about 20 pens stuck behind the dash, I have a feeling there's probably a dozen more things down there I probably need to clear out.

What are the stock shackle lengths for a scrambler? Any preferred vendor for scrambler items? I'm also going to replace the old brake lines with braided stainless, but I have to figure out whether I need stock length or extended first.
 
Back
Top