• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Jims "repair"-ation thread

I did not have much, mostly on the flat area of that lip
My body guy did the repairs
Do you think you could use some of a front fender ?

It looks like your body guy did an excellent job! Great idea, never thought about using a front fender before! When I get back to Kansas I will have to check and see if the dimensions and contours are the same. That would be great if worse case scenario we could use small sections of junk front fenders to repair the outer rear wheel well!
 
What I did for the factory tire carrier holes !
The holes On the crusher corners are three quarters of an inch in diameter
The head on a 3/4 bolt was huge
So I used a three quarter to half inch brass bushing by half-inch long and cut it down to 3/16" and mounted as the pictures show
ImageUploadedByTapatalk1355364809.698970.jpg
ImageUploadedByTapatalk1355364830.706546.jpg
ImageUploadedByTapatalk1355364845.250586.jpg
ImageUploadedByTapatalk1355364935.326851.jpgImageUploadedByTapatalk1355364967.484475.jpg
 
Love the progress pics!

Super idea on creating the Golden Eagle Scrambler!
 
Nice bushing idea! How about some stainless button head allen bolts instead of the hex heads- would really smooth it out.
 
Mmmmm , I'll look at lowes , Home Depot
Fastenal will want me to buy 50
Thanks !! ( to everyone )
 
They really do, but now I am scratching my head... and wallet, as I have the sliders, but I don't have the crusher corners and now I think I want them, but then I went and priced them and my wallet let out a yelp.

I do have a serious question though... on the website, they look like the crushers are cut for ROUND LED style lights, but on yours, it looks like a triangle or something... for running regular lights I imagine.

Are you running stock taillights or others?

cb
 
I have the rocker knockers and the crusher corners as well. Spring for the aluminium corners, well worth it for the weight savings.
You can get the corners with the round LED light hole or the triangle, which is for stock style lights.

SilverLakeAugust252012199-1.jpg
 
CB ,
Yes , I'm going to run stock taillights
This tub came from a trail vehicle and had very little rust
But the bottom and rear corners had trail damage
So these were the most cost Effective way to go , (for me)
 
And were they steel or aluminum that you went with?
I am thinking of asking Mrs. Claus to see if she is feeling the love for these.

cb
 
Bad karma
I could stare at pictures of your jeep all day
Can you explain to me how you have fullwidth Axles in your Jeep with stock fender flares
Are they cut down
Or do you have 18 inch rims with 5 inches of backspacing ?
 
And were they steel or aluminum that you went with?
I am thinking of asking Mrs. Claus to see if she is feeling the love for these.

cb

Mine are steel , i think I paid $500 shipped !
Aluminum would be great , but I am still sick to my stomach from spending 500
 
Bad karma
I could stare at pictures of your jeep all day
Can you explain to me how you have fullwidth Axles in your Jeep with stock fender flares
Are they cut down
Or do you have 18 inch rims with 5 inches of backspacing ?

Thanks!! :D

My axles are not full width, they were cut down by the axle's previous owner to, i think 62ish" wide (cant remember exaclty, so i could be wrong).
I am running 17" wheels (for brake clearance) and 5" back spacing. I would have liked alot less backspacing (2"-3") because the turning radius is affected since the front springs are out-boarded.
Body is still uncut, but its a bit bent on the rear lip from rubbage.
 
Back
Top