• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Joe's 1982 Scrambler Restoration Thread (Retitled From: Bringing The Scrambler Home)

my 1983 hood does not have the windsheild tie-downs and bump stop/loops for the windsheild support when it's folded forward.. my CJ7 had them.. is this the 7 vs 8 difference?

Are the holes there for the tie downs and windshield supports? My guess is your hood is aftermarket if the holes are not there. Or maybe a PO filled the holes in. Regardless, there is no difference in the CJ7 and CJ8 hoods. The tie downs and windshield supports should be there.
 
Joe,

The restoration is looking real nice! Did you find narrow track fenders for your 81 or did you use wide track fenders?

BTW, You work the same way I do... I install all the oem replacement parts (new and used) and get everything running correct before I even think about touching the cosmetics (paint, etc.) Nice work!

Jeff
 
Anyone? What's the difference in ANY CJ-8 hood?

Recesses for the radiator cap. Some have one and some have two.

Not the hood and not my jeep, but if you look at the grille below you will see two different recesses for the radiator cap. One is in the center right where the cap is at. The other is directly across from the upper hose. The hood would have similar recesses like the grille. If you had an offset radiator cap you would need the hood with two or your hood wouldn't close.

154_0211_08_z1983_jeep_cj7_buildupengine-1.jpg


This grille clearly only has one.

DSCF1158-1.jpg
 
On 82 and up CJ hoods, there is an additional indentation in the hood for radiator caps that are offset to the driver's side (in ADDITION to the center radiator cap indentation). In short, 82 and up hoods have two radiator cap indentations and 82 and lower only have a single center indentation.

Also... the length of the inside leading edge reinforcement (where the hood catch latches into) is shorter on 82 and up hoods (by something like an inch) than on earlier hoods.

Subtile changes... but they are definitely different

Joe mentions he finally found the correct hood for his Scrambler.

Question: How are they different? I though they were all the same, even onto the CJ-7 versions?

Please reply, as I am heading to actually buy a new hood today, and don't want to make a critical mistake? :(

Thanks for your replies!
 
Agreed. CJ7 and CJ8 hoods are the same... it's just that early CJ7/8 hoods are different than the 82 and up hoods. I'm not sure of the exact transition year, but my 82 came with the dual radiator cap indentations.

Are the holes there for the tie downs and windshield supports? My guess is your hood is aftermarket if the holes are not there. Or maybe a PO filled the holes in. Regardless, there is no difference in the CJ7 and CJ8 hoods. The tie downs and windshield supports should be there.
 
I used the factory wide track fenders off of an 86... my Scrambler is a wide track 1982.

In fact... I think our thread on seatbelts and axle widths suggests that that there are no narrow track 1982 Scramblers... it appears that 1981 was the last year for narrow track CJs

As far as working the same way you do... it really suits my style. I like driving my vehicles while I restore them AND, it seems easier to fix things one small thing at a time. I know it is less efficient doing it my way rather than tearing the whole thing down and restoring it... but I don't have the time, energy, or desire to do a frame off restoration.

This week's restoration project... intermittent wipers :D

Joe

Joe,

The restoration is looking real nice! Did you find narrow track fenders for your 81 or did you use wide track fenders?

BTW, You work the same way I do... I install all the oem replacement parts (new and used) and get everything running correct before I even think about touching the cosmetics (paint, etc.) Nice work!

Jeff
 
:cheers:There not !
WELL,EXCEPT FOR THE INNER FENDER IS DIFF FOR THE 81-86 FOR THE TALL SHOCK MOUNT
 
Last edited:
An update... that isn't much of an update

Hi Gang,

I thought I'd give an update on the Scrambler. It's been awhile since I did any work on it. Now that summer has started and my only plans are to work on my dissertation, I might actually be able to get some work done on the Scrambler. This past weekend I removed the half soft top and installed the half hard top and hard doors for summer. It's amazing how much better the A/C works with the hard top and hard doors... not to mention how much quieter it is :)

I also changed the oil and flushed the cooling system. I think the Scrambler is now ready for the worst that the Arizona sunshine can throw at it.

Hopefully I'll have some "real" updates for you soon.

Joe
 
Hi Gang,

I thought I'd give an update on the Scrambler. It's been awhile since I did any work on it. Now that summer has started and my only plans are to work on my dissertation, I might actually be able to get some work done on the Scrambler. This past weekend I removed the half soft top and installed the half hard top and hard doors for summer. It's amazing how much better the A/C works with the hard top and hard doors... not to mention how much quieter it is :)

I also changed the oil and flushed the cooling system. I think the Scrambler is now ready for the worst that the Arizona sunshine can throw at it.

Hopefully I'll have some "real" updates for you soon.

Joe

Funny, I think this is the first time I've heard of someone getting their Jeep ready for the summer by putting the hardtop ON and taking the softtop OFF! :D
 
This is my favorite type of rebuild. It starts with a jeep that's had a hard life, but not necessarily in need of a complete frame off rebuild, and you gradually get it back into shape while still driving and enjoying it. Its amazing what some cosmetic TLC can do for a jeep, keep up the good work! :thumbsup:
 
Hi Gang,

Oh... one thing I forgot:

Since this is the first time I've had the hard top on with the wood side rails, I thought I'd snap a few shots and share them. I understand this scrambler is somewhat of an ugly mutt... but I promise, someday I'll be posting pictures in this thread of her fully painted and looking sharp :)

attachmentphpattachmentid41154d130695708-1.jpg


attachmentphpattachmentid41155d130695749-1.jpg


attachmentphpattachmentid41153d130695707-1.jpg



attachmentphpattachmentid41152d130695707-1.jpg


attachmentphpattachmentid41151d130695707-1.jpg


attachmentphpattachmentid41150d130695707-1.jpg


attachmentphpattachmentid41149d130695707-1.jpg
 
"ugly mutt"? eye of the beholder...

I, for one, would have a tough time "ruining" it's current status in favor of a new paint job... although your mis-matched panels are kind of asking for it. If it was all the original blue paint/panels I probably would leave it as-is.

I have a strong internal debate on my own 83 right now.. as I'm reassembling it, I wonder if there's somehow a way I could preserve it's natural "patina" while still doing the required rust repair and prevention to further extend its life.. I almost feel like a complete resto might "ruin" it a bit.. for example, blast and treat the underbody and bed, while leaving/sealing the old paint/stickers on the outer panels..

in the end, just glad to see you back and posting updates..
 
A small update... The factory a/c blower motor is squealing like a stuck pig. I took apart a spare that I had laying around to see if I could rebuild it, but frankly, a replacement motor from jeepair.com is only $40 or so and the factory motor i had was rusted a bit inside. I went ahead and ordered a new motor and squirrel cage and the total order was around $69 with shipping. As soon as it arrives, I'll install it. These simple a/c systems are a piece of cake to work on.

Working on the scrambler is a bit slow these days as I begin working on the preliminary research for my dissertation. Ug... I'll be so glad when I finish this damn degree :)
 
The paint on my scrambler is so oxidized and the mismatching panels are a bit of an eyesore to me... I really want to paint it. If I had a "normal" original paint job, I'd never paint over it. I'm not doing a body off paint job. I'll remove the fenders, grill, hood, tailgate, and roll bar and have the pieces painted at the same time I have the body painted. I'll strip down the hard doors, weld up the cracks and reinforce them, and have them painted at the same time. Then I'll put it all back together. The undercarriage is in great shape so I won't touch it. The only thing I'm wondering if I should do is remove the engine to paint the firewall. It is in ok shape but is far from perfect. Suggestions?


"ugly mutt"? eye of the beholder...

I, for one, would have a tough time "ruining" it's current status in favor of a new paint job... although your mis-matched panels are kind of asking for it. If it was all the original blue paint/panels I probably would leave it as-is.

I have a strong internal debate on my own 83 right now.. as I'm reassembling it, I wonder if there's somehow a way I could preserve it's natural "patina" while still doing the required rust repair and prevention to further extend its life.. I almost feel like a complete resto might "ruin" it a bit.. for example, blast and treat the underbody and bed, while leaving/sealing the old paint/stickers on the outer panels..

in the end, just glad to see you back and posting updates..
 
My Scrambler originally came with a white rear bumper but the one that was on it was completely trashed (see some of the opening pictures in this thread). Because I couldn't find a white bumper, I ended up purchasing a NOS chrome one, having the chrome stripped off, and then having it powder coated white. I seem to recall that the chrome bumper was around 150 and it cost me 90 for the chrome stripping, sand blasting, and powder coat. Talk about an expensive bumper!

I purchased the chrome bumper from a place recommended by this site, but I think they are all gone now. However, they do crop up for sale periodically.

Maybe someone here knows where to find the original white bumpers... I failed when I tried to find them.

Joe

I like that rear bumper, where did you get it?
 
My Scrambler originally came with a white rear bumper but the one that was on it was completely trashed (see some of the opening pictures in this thread). Because I couldn't find a white bumper, I ended up purchasing a NOS chrome one, having the chrome stripped off, and then having it powder coated white. I seem to recall that the chrome bumper was around 150 and it cost me 90 for the chrome stripping, sand blasting, and powder coat. Talk about an expensive bumper!

I purchased the chrome bumper from a place recommended by this site, but I think they are all gone now. However, they do crop up for sale periodically.

Maybe someone here knows where to find the original white bumpers... I failed when I tried to find them.

Joe

My cj8 has the orginal chrome bumper, but both seem really hard to find.
Id like to find either, if you come across any let me know
 
Back
Top