• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Mercedes OM617 diesel swap???

https://www.facebook.com/photo.php?...14261814854.2144435.1236189592&type=3&theater
photo.php

photo.php

photo.php
 
Last edited:
BTW, this swap favors the stock 4 speed tranny. I have spoken to guys who have swapped in the AX 15, and the Merc just doesn't like it. It smokes and bogs down, asking you to rev higher. Another reason that this is a cheap swap. Just bolt it to the CJ tranny, and go have fun.

What tires and axle gearing do you have? I am real close to pulling the trigger on a diesel swap with either modified SD33T (have), military 6.2 (have and is low mileage) or MB (don't have but have source from MB mechanic friend). Do not wheel my Scrambler (have a trail rig) and it is not my daily driver. Have too many rigs/toys can't justify the cost of 4BT and don't need the power.

I have owned several MB diesels over the years and love the engine. I also like the simplicity of mechanical injection and hour comment about non OD transmission. I would use TF999 (have several) in either lockup or non lockup.
 
What tires and axle gearing do you have? I am real close to pulling the trigger on a diesel swap with either modified SD33T (have), military 6.2 (have and is low mileage) or MB (don't have but have source from MB mechanic friend). Do not wheel my Scrambler (have a trail rig) and it is not my daily driver. Have too many rigs/toys can't justify the cost of 4BT and don't need the power.

I have owned several MB diesels over the years and love the engine. I also like the simplicity of mechanical injection and hour comment about non OD transmission. I would use TF999 (have several) in either lockup or non lockup.

I have 33" tires with 3.73 axles. Climbed the Ute Pass today (6000 ft to 9500 ft and it held 55 with no problem. Lots of turbo noise ;-)
 
Yes, not needing to worry about the overdrive is one of the main the arguments for the OM617. HUGE powerband.

Sweet! I have 4.10 gears with 35" BFG ATs and my concern with both the SD33T and 6.2 is they both have fairly narrow power bands. I have a WC T5 behind my tired old 4.2 and it struggles to hold 70 on the Interstate with a head wind and flat ground. Promised the wife would make it an auto when I replaced the engine.

Did you do a writeup on your MB engine swap? Would love to hear and see pictures of how you did motor mounts, power steering, etc.
 
Sweet! I have 4.10 gears with 35" BFG ATs and my concern with both the SD33T and 6.2 is they both have fairly narrow power bands. I have a WC T5 behind my tired old 4.2 and it struggles to hold 70 on the Interstate with a head wind and flat ground. Promised the wife would make it an auto when I replaced the engine.

Did you do a writeup on your MB engine swap? Would love to hear and see pictures of how you did motor mounts, power steering, etc.

http://www.mercedesdiesel4x4.com/

I don't have a writeup, but I will answer any questions that you may have. Check out this link. All the motor mounts, exhaust, adapters, etc can be found here. Nathan is the owner, and he is very helpful. As for power steering, just take the Mercedes lines and the Jeep lines to the local machine shop, and they will weld them together for about 30 bucks.

Cheers,

Greg
 
Hey Greg, you make the swap sound like it is really simple. I've reviewed that site in the past, and it seems like motor mounts and an adapter plate is all there is to it. Isn't there any concern about the old fuel lines and tank, exhaust piping, radiator, etc.? How much of the MB guts does a person need, to properly perform this diesel swap?

Also, how much spring lift was required for you to clear the front axle?
 
The T176 would be a great tranny for this swap. I have a T18 but i want to run the Dana 300 and the adapter for that is very pricy. I noticed that they have an adapter to fit the T5 which i have but the strength would scare me a bit with the higher torque rating of the diesal motor.
 
I noticed that they have an adapter to fit the T5, which I have, but the strength would scare me a bit with the higher torque rating of the diesel motor.

I don't think the MB diesel has very much torque. This was the reason I never paid a lot of attention to this motor until this post, that is, since it indicates that a user experiences good success at our steep inclines in CO. Torque is king, but I think the OM617 has less than 200lbs., which isn't much different than the 258-I6. I could be way off on this, but that is what I remember reading once.
 
Hey Greg, you make the swap sound like it is really simple. I've reviewed that site in the past, and it seems like motor mounts and an adapter plate is all there is to it. Isn't there any concern about the old fuel lines and tank, exhaust piping, radiator, etc.? How much of the MB guts does a person need, to properly perform this diesel swap?

Also, how much spring lift was required for you to clear the front axle?


Nathan actually publishes a list of needed donor parts on his website. Just follow the link that I provided earlier. I have 2.5 inches of lift, and I had the oil pan notched so it would not contact the diff. Cost 70$ to notch the oil pan. Nathan recommends about 4 inches of lift even if you use his oil pan. I've been fine so far with my setup.

Greg
 
I don't think the MB diesel has very much torque. This was the reason I never paid a lot of attention to this motor until this post, that is, since it indicates that a user experiences good success at our steep inclines in CO. Torque is king, but I think the OM617 has less than 200lbs., which isn't much different than the 258-I6. I could be way off on this, but that is what I remember reading once.

Your are correct. The OM617, in stock form, has basically the same HP and TQ as the 258. The turbo is wastegated to reach about 9-12 PSI. It can be turned up to reach as high as 30 PSI from what I've read on other forums. The ALDA on the IP can also be adjusted for more power. Real gains can be reached if you change out the IP (1200$) and install an intercooler. If I were to do all that, I would have gone with the Cummins and a larger pocketbook. This swap was a good cheap swap for me. Additionally, I have gained better high altitude performance here in Colorado as the turbo keeps the engine pretty normalized at these altitudes. The 258 was always at full throttle and using way too much fuel. I live at 9500'.

Greg
 
Nice feedback; thanks, Greg. I spent 1988-1995 with my CJ-8 at 9604' and mostly only upwards from that elevation. My 258 was an absolute dog, especially with 2.73 in the axles for some of those years. One of those years, I knew a gal that had an '83 CJ-7 with a 258 that would smoke me on the paved pass roads, but never figured out her secret.

That MB diesel option would suit me fine, if you say you have no problem maintaining decent speed on long, steep inclines with a lot of slow curves, and your foot not mostly holding the throttle pedal to the firewall. What is your average fuel economy for typical paved mountain road travel?
 
I lived in utah fora number of years when I CJ5 had the 258 and it had troubles at the higher altitude. I drove it accross Wyoming and I had the throttle wide open for a four hour stretch going up to 10000ft and i could only hit 50-ish at some points.
 
I drove a 82 300SD Turbo yesterday. I was impressed. There was one hill about 3 miles long. I played with it all the way up. Dropped down to 55 then up to 75. You get the picture. Different speeds all the way up. There is so much torque through the power curve the automatic transmission didn't shift down once. It is so much quieter than my powerstroke. If I didn't have other issues going on. I would be all over this.
 
When I drove through some of the higher passes in Colorado with my MPI equipped 258, I noticed a pretty good loss of power at the higher elevations, like only having 2/3 the power. Up at those altitudes, gas vs diesel isn't as important as naturally aspirated vs forced induction (turbo or super charged):twocents:

It was like the engine couldn't breath/suck in as much oxygen at the higher elevations. I think forced induction would be the way to go, basically "cramming" more air into the cylinders then what can naturally be sucked in:twocents:

I wonder how a turbo/super charged 258 would perform compared to the smaller turbo diesels:shrug:

That is a very cool engine swap:thumbsup::wave:
 
Back
Top