• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Power Steering fluid Leak

I had a similar leak after my engine swap.

A minor seal kit was $15.
A major seal kit was $100
A rebuilt unit was $140 after core fee at AutoZone. This is what I ended up doing and so far it is fine if the 4 turn ratio doesn't bother you.

Hi - Would you mind explaining the 4 turn ratio?
 
This looks pretty intimidating:
When I think of a Hummer I think more off road, heavy duty. Since my 8 my daily driver and I only do light trails and she has no lift and everything is stock – is it still a suitable choice?
Also should I be able the find a stock # on the box, incase I can get a rebuilt from NAPA?
I am also wanting to learn about the 4 turn ratio??
As always you are a great help everyone.
Wayne.
 
This looks pretty intimidating:
When I think of a Hummer I think more off road, heavy duty. Since my 8 my daily driver and I only do light trails and she has no lift and everything is stock – is it still a suitable choice?
Also should I be able the find a stock # on the box, incase I can get a rebuilt from NAPA?
I am also wanting to learn about the 4 turn ratio??
As always you are a great help everyone.
Wayne.

It will be heavy duty, but will not be harder to turn, or diminsionally any different than your original steering box, except the piston cap will be bigger. It will bolt right on, look stock to the untrained eye, and steer a little easier than the OEM box. The ratio on the H1 box is exactly the same as the AGR Super Box 2. My AGR Super Box 2 drives great on the highway, but is a little easier to turn than the stock steering box. My other Jeep is going to get an H1 box if the leak gets much worse.
 
It's not the fancy name but what use to be a good product. I've had bad luck with rebuilt products, a new upgrade (currently running 33" thinking of going to 35" tires) would have been a good investment. It's a shame quality control went south. May be checking on the h1 box or seeing if my mechanics rebuilder (had to have work truck steering box rebuilt, having problems getting good rebuilt boxes up here) can rebuild the cj7's box.
 
Ok.. Lets back up a bit.

As information: Most of the components like steering columns, steering gear box, brake master cylinders, etc.. on our Jeeps are "off the shelf" parts that AMC bought form GM or Ford or whoever, and used in Jeeps.

The steering box in our Jeeps from factory is a Saginaw gear box (and it uses a Saginaw pump too). They have a few mount styles, fitting styles, shapes, ratios, and sizes. A larger bore makes larger tires easier to turn. So does a higher ratio box. Our Jeeps came stock in the 80s with a 4 turn box. That means 4 turns from all the way left to all the way right. Modern cars are typically 3 to 3 1/2 turns. Some even less. That is what I mean by 4 turn ratio.

What wm69 is saying is - the box he is suggesting is an upgrade to the stock unit. I didn't know about it when I did mine or I would have tried it. Sounds like a good choice as it uses the same fittings you would have on stock 80's power steering lines. It also has the same bolt mounting pattern so it will fit stock brackets, and stock pitman arm connection to steering rods. It will also be between 3 and 3.5 turns lock to lock.

When he says variable rate, he means that the amount the tires turn, relative to how far you turn the wheel, varies from slow/small amount when you start turning the wheel to fast/larger amount as you get closer to full turn. This came about as a feature after our jeeps were made to reduce number of turns lock to lock while keeping highway speed steering adjustments slow and parking lot speed adjustments faster and easier to turn wheel.

If you have ever driven a car frm the 60s with power steering, those usually had 6 turn boxes. Your hands look like a boxer at the speed bag when you are trying to park one of those things. That gets old if you do it a lot, so better gears, variable rate, etc.. was developed.
 
So I stopped by my local NAPA store on the way home out of curiosity for $150.00 plus my my box they will sell me a Cardone like CBFord said for $150.00 with a warranty - but the 4 turn ratio you mention has got me confused.
Wayne.
 
It means it takes 4 turns of steering wheel to go from all the way left to all the way right.
 
Wow interesting - I need to turn my wheel and see what I turn now. Why is that, gears or something???
 
Something to keep in mind, even if you can manage to reseal the box well, it's still going to have 30+ years of wear. Replace it with a rebuilt or new one.
 
Part number you can use to search or have a place like Napa cross reference it is: 27-7595

The H1 Box is a direct bolt in, requiring no modifications, as long as your Jeep has the metric power steering lines and o-ring seals. Many of the other off the shelf steering box upgrades require minor alterations like changing the lower steering shaft coupler, etc. The H1 box does nor require any of this.

A good number of my CJ's are now running the H1 Hummer steering box. Whenever I have an old steering box start the inevitable leak, I replace it with the 27-7595 unit.

While I'm replacing the steering box and have it pulled out I go ahead and upgrade to the MORE steering box mount and MORE steering box brace, as well as change out the steering shaft to a Borgeson model.

These parts combined make a huge difference in the way my CJ's drive. I'm so impressed with how my Jeeps drive after installing these parts that I keep and extra set of each on a shelf ready to be installed on the next Jeep once the old seal lets go on the steering box! Don't forget to change out your power steering lines while you have it all apart so you won't have to do it later.
 
Part number you can use to search or have a place like Napa cross reference it is: 27-7595

Thanks for info and part number.

I'm so impressed with how my Jeeps drive after installing these parts that I keep and extra set of each on a shelf ready to be installed on the next Jeep once the old seal lets go on the steering box! Don't forget to change out your power steering lines while you have it all apart so you won't have to do it later.


I was thinking that is a little excessive until I scrolled down and saw your signature. :huh:
Quite a collection. :bow:
 
Sir:
How do I tell is my Jeep has the metric power steering lines and o-ring seals??
Thanks.

Part number you can use to search or have a place like Napa cross reference it is: 27-7595

The H1 Box is a direct bolt in, requiring no modifications, as long as your Jeep has the metric power steering lines and o-ring seals. Many of the other off the shelf steering box upgrades require minor alterations like changing the lower steering shaft coupler, etc. The H1 box does nor require any of this.

A good number of my CJ's are now running the H1 Hummer steering box. Whenever I have an old steering box start the inevitable leak, I replace it with the 27-7595 unit.

While I'm replacing the steering box and have it pulled out I go ahead and upgrade to the MORE steering box mount and MORE steering box brace, as well as change out the steering shaft to a Borgeson model.

These parts combined make a huge difference in the way my CJ's drive. I'm so impressed with how my Jeeps drive after installing these parts that I keep and extra set of each on a shelf ready to be installed on the next Jeep once the old seal lets go on the steering box! Don't forget to change out your power steering lines while you have it all apart so you won't have to do it later.
 
Regarding the ref number for the steering box 27-7595 would you know if it is a Cardone steering Box?
Thank you
 
I believe the o-ring metric lines are found in the 1980+ CJs. 1979 and prior would be the flared fittings. The two nuts that thread into the steering gear box are 16mm and 18mm. The 27-7595 is a cardone part number. Hope that helps!


Sent via smoke signal
 
I received my H1 steering box last night - wm69 thanks for your help.
Before I tackle the project this weekend is there anything I should know or do before i do this.
For example once everything is back together - will I have air in the lines and will the lines need bleeding???
I am going to remove the radiator - it looks like it's easier to get the the steering box if it is out.
Thanks,
Wayne
 
Soak the crap out of the mounting bolts with Kroil or PB Blaster before you try to remove them. A torch would be good too. There are nuts welding INSIDE the frame and bolts that hold the steering box mounting bracket go up into those nuts. It is not unusual at all for those nuts to break loose in the frame, resulting in a spinning bolt that won't come out. Since they are inside the frame there is no easy way to get at them.

If it were me I'd be loading up the inside of the frame above the steering box mounting bracket with a whole lot of penetrating oil.
 
This steering box is a tough swap.
Can anyone answer three questions please.
1. I have read on threads that the nut under the grill will/can keep turning. I am trying to find out what is on the other side of the nut – under the the grill. Would anyone have any photos? I am curious to know why it keeps turning?
2. Also, the steering shaft, does it slide straight into the steering box?
3. Anyone know what size that nut is under the pitman arm. I need to buy a wrench since nothing I have fits.
As always, cheers
Wayne.

NUT SIZE.jpg
 
This steering box is a tough swap.
Can anyone answer three questions please.
1. I have read on threads that the nut under the grill will/can keep turning. I am trying to find out what is on the other side of the nut – under the the grill. Would anyone have any photos? I am curious to know why it keeps turning?
Captured nut up in there. If it's spinning you either gotta figure out a way to bind it up, or you might have to grind the bolt head off, pull the grill, and cut the captured nut out and replace.

http://www.jeep-cj.com/forums/attachments/f98/11526d1348984303-aussie-cj7-78-grill-06.jpg

2. Also, the steering shaft, does it slide straight into the steering box?

You'll have to remove the index bolt and nut from the bottom that holds the steering shaft onto the steering box. Then it pulls up off the box (it's splined). Good luck. The only time I've done this it was NOT easy coming off.
3. Anyone know what size that nut is under the pitman arm. I need to buy a wrench since nothing I have fits.
As always, cheers
Wayne.

View attachment 53455
Not sure on that one, but you'll probably need a gear puller or a pickle fork to get the pitman arm off once you get the nut off.
 
Awesome - yeah if I can get the front grill of it will make life easier, what a pain though.
Cheers.
 
I just notice the picture - great, so the nut goes up into that long piece. I wonder why it keeps turning, strange...
 
Back
Top