• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Power Steering fluid Leak

The nut on the box holding the pitman arm is 1 5/16". Leave it threaded on the end of the shaft when you use a quality pitman arm puller. Use penetrating oil and follow instructions on how to use the puller.
 
Get a pitman arm puller. VERY doubtful a pickle fork will do it. Like John N said, " a quality " puller.
 
My UK red neck approach as they are only cheap to buy is just cut the pitman arm until almost through with the grinder (dont go in to the threads!) and then split it with a chisel and fit a new one.
Some grease sat over where the seal is stops the grinding dust getting in, I have never seen a Pitman arm puller its a USA specialty i think!
 
A gear puller will do. Usually not too hard to pull the pitman arm. Worse case if it'still stock, someone probably has a arm.
 
Anytime I pulled them, they were a PITA to get off. The one sounded like a small caliber rifle when it finally let go, yea it startled the heck out of me.
 
Cheers mate - that will probably be my UK Redneck approach aswell
 
Hello:
Changing out this steering box is turning out to be quite the challenge.
I have two questions please.
It looks like I have one nut that needs to be removed in order to remove the steering box. The issue is it is in a horrible place, it is way in the back of the bracket that secures the steering box and I have no idea how to get to that nut. For those of you have removed the steering box can you please tell me how I get a wrench on the end of that strange looking nut or am I missing something here?
There is the large cross member/plate the goes from the right to the left of the frame in the front. On the steering box side there are two nuts and bolts. There are no bolts on the other side (passenger’s side) but that plate is also welded so even if I can undo the nuts I still cannot get access to the last bolt holding the steering box. I am totally at a dead loss here.
Hopefully the photos will do a better job explaining where the strange looking nut is.

*Also, do I need to remove the steering wheel to pull the steering column?
As always thank you kindly,
Wayne.

Nut 1.jpgNut 2.jpg
 
I always pull the steering box and the steering box mounting brackets as one unit; only 5 bolts total to do this. Two bolts through the top of the front crossmember. Then there are three bolts on the bottom of the left hand side frame rail. Two of these bolts also attach the shackle hanger to the frame. The third bolt is just behind these two bolts, bolted to the bottom of the frame rail.

While you have the steering box out I would recommend upgrading to a much stronger steering box mounting bracket like M.O.R.E. makes.

No need to pull the steering wheel to pull the column out.


Sent via smoke signal
 
Down side is those bolts are usually heavily rusted if a northern jeep. Use plenty of penetrating oil, let it soak for a couple days, reapplying every day. May also need a torch for heat. If possible you don't want to break the bolts or the carriage nuts. It can open another can of worms.
 
I guess I need to take another look at the bolts. I see the three that are on the bracket under the frame ( all three broke/snapped even after lubricating for days). I am not that concerned about the broken bolts I can tweak and modify the bracket. I just need to find the other two bolts I guess.

I have loosened the nut at the bottom of the steering column - should the steering box slide of the column?

Thanks

I always pull the steering box and the steering box mounting brackets as one unit; only 5 bolts total to do this. Two bolts through the top of the front crossmember. Then there are three bolts on the bottom of the left hand side frame rail. Two of these bolts also attach the shackle hanger to the frame. The third bolt is just behind these two bolts, bolted to the bottom of the frame rail.

While you have the steering box out I would recommend upgrading to a much stronger steering box mounting bracket like M.O.R.E. makes.

No need to pull the steering wheel to pull the column out.


Sent via smoke signal
 
I have broken three so far, even after soaking for days.
So the nut with the strange looking head is a carriage nut?
 
If you got the three under the frame loose, you need to take out these 2. Located on top of cross member that holds up your grill shell.
strg brkt blts.jpg
 
I got home from work and the first thing I did was locate them and did what you recommended, I took the whole brackets of. The nuts came quite easily - I was very surprised.
(By the way that cross member on your photo looks nice - much better them mine, did you replace it??

For three days I have been working on the pitman arm and I cannot get it of. So I am going to remove it along with the with the steering box and work on it in the vice.

The issue I have now is that the steering box will not slide of the steering shaft...
Is there a trick to this? I have attached a photo - does the ring at the end of the shaft need to come off? I was expecting to just pull on the steering box and was hoping it would slide of..
Also what is the trick to get the steering shaft of at the steering column end??

Cheers.

Slide1.jpg
 
The steering shaft goes over the input shaft of the gear. If I remember right (you need the bolt out which is what you did), carefully take a long screw driver or tire iron (kind that has a flat blade end) and put between the steering gear housing and bottom of steering shaft (under the clamp you have pictured). You will need the bolts loosened or removed for the steering gear. Now pry (top of long pry bar, tire iron or what ever your using) handle of pry bar toward firewall (which will try to push steering gear to bumper. Steering shaft won't move, gear will slide out of shaft (that's why you need bolts loosened or removed. Depending on what you have when you put the new gear on you may have to align a flat spot on steering gear (input shaft) with flat spot on steering shaft. when you put the bolt back in it slides along this flat spot to lock together. Some gears have this flat spot others have a grove cut in that the bolt slides along to lock in. So may, can't remember which one you have.
 
Awesome - wow it sounds like Jeep surgery.
I will attack this when I get home from work tomorrow.
Thank you so much.
Wayne.
 
I'm running that same Mountain Offroad brace on all my CJ's with the H1 27-7595 steering box. It bolts up perfect, no modifications necessary.


Sent via smoke signal
 
Interesting, does it just bolt to the frame or does it still bolt to the cross member where the grill sits?
Thank You.
 
Back
Top