• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Q-Tec winch- Ordered, now installed and the review begins...

Randyzzz

Blown Budget
BENEFACTOR
Gold Member
Lifetime Member
SOA Member
City
Redmond
State
OR
After selling my Warn 9000i and realizing the 8274 looks too big and blocks too much radiator, I have been on the lookout for a new winch. Craigslist has been dry lately, so I started looking at the "lower price" units. Heard a lot of good about Engo, but then I saw Q-Tec had their winches in black. I trust their customer service, and the specs look good. So, since EBay has been very, very good to me lately, I took some of my profits and gave Q-Tec a call and ordered one of the Q9000 winches. Should be here in a few days, I'll post up pics and do a mini-review.

By the way- did you know that if you tell Q-Tec you're a forum member, and give them your screen name, you don't pay shipping? I found out about this on wranglerforum.com, so I registered there, in case it was forum-specific. After talking to the guy at Q-Tec, I think being a member of any forum probably works. Saved $50 in shipping charges!:woot:
 
Last edited:
By the way- did you know that if you tell Q-Tec you're a forum member, and give them your screen name, you don't pay shipping? I found out about this on wranglerforum.com, so I registered there, in case it was forum-specific. After talking to the guy at Q-Tec, I think being a member of any forum probably works. Saved $50 in shipping charges!:woot:

Good to know!!
 
Wish I knew that when I ordered mine. And I too was glad to see them come in black. So which did you get? And where are you planning to mount the solenoid? I thought about the side mount, but it was blocking the turn signal.
 
I went with the black Q9000. I figured that would be enough pull. As far as the solenoid, I don't know yet. I like the side mount idea best, but the turn signal is an issue. I might just go with the center mount for now and do a remote mount later. Or remote mount some LED turn signals and put mesh over the stock t/s holes and use them for more air intake.Seeing the winch on yours was one of the reasons I really looked into them.
 
It was the first winch I ever mounted. The instruction pics are great by the way. My only mistake was mounting the winch to the plate before putting the fairleed on. Had to take the winch back off to mount the fairlead. Oops.
 
I was going with the 8274 but to find one any more there like 600 bucks, think i will go with the 11000 one from Q-tec
 
I don't own one of these winches, but I have been around them when they are being used. They do the job, but they are slow/noisy/pull a lot of "juice" compared to a Warn:twocents: But, they do get the job done:thumbsup:

On a side note, I pulled out a 4x4 diesel Excursion, which had a 20' car hauler trailer on the back, from the mud in Louisiana during our last jeeping trip. Pulled it up a hill, through the mud, for about 80', single line pull. My Warn 9.5ti never even got warm, pulled smooth and silent, the remote never indicated a "hot" condition:headbang: I am willing to bet that rig that I pulled was slightly over the 9500 pound limit:rotfl: I am just using a stock alternator and an old blue top Optima, I never dropped below 12 volts, kept the RPM's around 1800:rotfl:

I thought about buying a "cheaper" winch during my build, mainly to save some money, but when I was on the receiving end of my winch at the hard spots of Pritchet Canyon, knowing that my winch was the deciding factor between making it through and potentially rolling my rig, I was very happy/confident knowing I had a Warn up front:twocents:

I had remote solenoids on a 12000 pound Warn that I had. They separate solenoid boxes seem to be more susceptible to moisture damage when mounted on the exterior of the vehicle. I ended up mounting the plastic solenoid box under the hood, on the top of the driver side fender, to keep the rain/car wash water out. Might be something to think about:twocents: I have seen quite a few 8274's non-functional as a result of moisture damaged solenoids/corroded connections inside the boxes.
 
Last edited:
Just checked the tracking number...it will be here tomorrow!

I had considered the 11K, but figured the 9K would be enough. If I'm not impressed, it will be the one that gets mounted under the rear. If I am really impressed, I might just get an 11K for the front and still put the 9K under the rear.

I've still got the three 8274's I'm going to be restoring for resale, complete with the reprint SE stickers. I'll post up when that happens.
 
How much are you planing to ask for the 8274's? I was looking pretty hard for one until you said it was too big and covered the grill. How much does it block?


 
Here's the 8274 mounted. It blocks quite a bit.
attachment.php


I'm planning on cleaning, polishing, repainting, resealing, replacing broken parts, and putting on a repo Jeep SE decal. I was going to start at $600, but I think once I get them done they will be worth a bit more. A lot depends on how much I have to put into them. I already have the seal kits, plugs and new solenoid covers. One will get a new motor too. I'll post up when they are ready. Don't hold your breath though...life is moving full speed right now. Unless you want to "commission" a build.

Ok- the review starts next post!
 
Q9000 review begins here!

Quadratec provides great customer service- that's one of the reasons I picked their winch over some of the other comparable units. To illustrate this point- I ordered on Monday, and the winch showed up today! 2 days- I like that.

The packaging was excellent.
007rs.jpg

Everything suitably secured and isolated.
009rs.jpg

Thank You!
010rs.jpg

The winch body. The decal was a little crooked, and i really didn't care for how it looked anyways, so I removed it.
011rs.jpg

The accessories neatly packaged. So far, so good.
012rs.jpg
 
Tools required were listed. Some weren't needed, but they omitted a 15mm and 16mm wrench for the fairlead and mounting bolts.
019.JPG

The instructions were some of the best.
020rs.jpg

Separate warranty sheet and glovebox instruction manual.
033rs.jpg

In the manual was a place to write your serial numbers. Of course, I didn't open the manual until after it was all bolted down...
034rs.jpg
 
On to the install. The mounting bolts were 10.9- good and strong. The nuts that went into the mounting feet were standard shoulder hex- not the usual square nuts we're used to. The feet were designed to capture the hex nuts just like square ones.
013rs.jpg

The fairlead had a couple of special low profile bolts.
014rs.jpg

I figured everyone would want to see what was in the solenoid box. One big contactor.
015rs.jpg

It looks well made.
018rs.jpg

Installing the solenoid box was my first snag. I had intended to mount the box on the rails, as a side mount would obscure most of the turn signal. I bolted the adapters to the solenoid box, and attempted to mount it to the rails. The adapters were too narrow to span the rails, so a bit of bending did the trick. But- when I attempted to tighten down the retainers, they were too short. The screw wanted to pull sideways, and the retainers just halfway grabbed the rails. I wasn't pleased with this, so I decided to go with the side mount. Of course, now there's scratches on the aluminum rails. The picture shows how the bracket is mis-built. The top is as designed, the bottom is how it would need to be to mount securely. The small screw binds up before the retainer secures the bracket.
021rs.jpg
 
Fast forward to the installed product. Got ahead of myself with the picture taking. It really looks good mounted there.
022rs.jpg

Overall impression is that it is a well built quality product. Nothing loose, nothing feels cheap.
023rs.jpg

Well, OK, the wiring feels a bit cheap. The boots were made of a vinyl that I'm fairly sure will get brittle in the sun quite rapidly. Time will tell and I may eat my words...but regardless, the boots didn't fit well at all.
030rs.jpg

The wiring and insulation was very flexible, but they felt like cheap jumper cable wire instead of good welding cable. Again- time will tell. Everything is color coded for easy installation.
031rs.jpg

The battery cables were long enough, and the ends were heat shrink sealed. the battery cables felt a bit better quality.
029rs.jpg
 
The remote looked just like a Warn- except it is bright orange and really rubbery. Soft, bendy rubbery. It has a slot in the lower handle, for a strap I guess. I like it.
025rs.jpg

The socket is 4 pin and has a soft vinyl cover. It has external threads for the remote plug.
032rs.jpg

The 12' cable from the remote screws on securely. Do I like this? Not really- if you ever slip while holding the remote, something's going to break. I'd rather pull it out than break it out. The screw in connection felt tight like most plastic screw connections. I just think it will break under strain while a straight plug with no screw in would release under strain.
024rs.jpg

Typical hook- looks good. Wish they would have spent a couple cents and put a thimble in the loop.
026rs.jpg

Cable- appears good, but what did they cut it with? A torch??? There is a nasty sharp end hanging out of the crimp...
027rs.jpg
 
Last edited:
This ends the install portion of the review. I need to stretch the cable, it started raining so that will wait until another day. I did spin up the motor and it and the gears sound good. Real good - quiet and solid.

I'm happy with the winch so far. The minor install issue and quality concerns are minimal, especially at this price point and when everything else looks so great. Good job so far, Quadratec!


I couldn't figure out why they spaced the solenoid box up 3/8" from the mounting surface, and was going to take out the spacers- but they allow the turn signal to peep through, so I guess I'll leave them for now.
028rs.jpg
 
Hey Randy. Great write up. I agree with everything you said (especially the boots on the wires. But I mounted mine on the top (rails). While I did have a little trouble with one of the connector screws, I got mine to eventually thread straight and holds well.
 
Back
Top