• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Scrambler on a budget

another great day out

finished the roll bar 4 coats spray bombed on it

IMG_2551-1.jpg


IMG_2554-1.jpg


the 1/2 door panels needed some black vinyl spray. that stuff is great.

IMG_2553-1.jpg


IMG_2555-1.jpg


finished up the axle bearing and put the wheels back on so now its almost ready to drive.

IMG_2556-1.jpg


roll bar is in

IMG_2558-1.jpg


bulkhead

IMG_2559-1.jpg


7 more parts left to paint and install and it should be done for at least a few years.

IMG_2561-1.jpg


IMG_2560-1.jpg
 
"Done for a few years" - First Jeep HUH.

HAHAHAHA thats what i told my wife. but really i meant by it was major stuff like the engine. i hope to swap in a diesel from an old benz.
jeep-2.gif


wasnt referring to the crap that breaks
forum
 
Last edited:
i did a lot of small stuff; still waiting for parts like windshield seal hood stops and a few more little things.

i really want the led taillight treatment but it will have to wait a quite long time, those things are pricy.

http://www.polyperformance.com/shop/Savvy-Off-Road-LED-Tail-Lights-p-21218.html

so i fixed up the old ones. man they are ugly now that the jeep is so legit.

IMG_2562-1.jpg


the shocks were next.

IMG_2563-1.jpg


IMG_2565-1.jpg


next i added some more rock lights these will light the rear end. i have 2 more mounted just below the front seats on the frame. these lights have been lying around my garage for about ten years.

IMG_2568-1.jpg


IMG_2569-1.jpg


IMG_2570-1.jpg


here it is finished; all thats left is to bolt on the tailgate.

IMG_2564-1.jpg


took it out for a ride and it drives awesome. i think the bad axle bearing was robbing a lot of HP because it never felt this strong.

celebrated with a cold 1

IMG_2566-1.jpg


IMG_2567-1.jpg


i think my dog just claimed her seat.

IMG_2572-1.jpg
 
Get rid of those shock boots if you want the shocks to last a while. You might be surprised at the mud and grit that falls out when you cut them off. They harbor lots of mud and water that will rust up the rods. My buddy laughs at me every time I see a shock boot because I start looking around, "Wherrrre's my BOX KNIFE..."

Damn fine Scrambler though!! And just one year??? Amazing. I've gone a whole year w/o even touching my pile of parts that will one day become half as nice.
 
got a few parts in
windshield gasket. this is not a DIY project. i tried what the forums said got it 90% in but was afraid of breaking it.

IMG_2573-1.jpg


IMG_2575-1.jpg


IMG_2576-1.jpg


IMG_2574-1.jpg


i took it over to safelite and they broke it for me, they broke one of theirs as well. the 3rd time was the charm LOL

the bumper, winch, windshield, mirrors, and bikini top are all on. its drivable now, but the weather sucks.

IMG_2577-1.jpg


IMG_2581-1.jpg


IMG_2586-1.jpg


IMG_2587-1.jpg


IMG_2583-1.jpg



IMG_2584.jpg


ill drive tomorrow and hope for the best. there is a truck show this weekend but i might not enter it due to lack of doors, tailgate, rocker knockers and air vent grill. i was really trying to get there but siht didn't work out.
 
no pix on this repair, a first LOL
the valve cover was leaking so if anyone reads this they can learn from my mistake.
i didnt trim the gasket to fit and i used the blue silicon sealer :angry:
the aluminum cover with cork gasket worked for a few months but the gasket shifted in the back dr side.
when i removed it i saw right away
SO trim it to fit without any part lifting up
USE black RTV then place the gasket on the cover and weight it down with small tool box or something for 1HOUR
now the gasket wont shift and when you go to put it on
torque it down lightly and re-tighten it a few times after you drive it. dont over tighten :D
 
Last edited:
i was under the jeep today after a nice ride treating some rust under the tub. i grabbed the rear and it was pretty warm, too warm i thought for the length of the ride.
i had planned to service anyway, i had the gasket and oil since last year. i did the pinion seal a few months ago.

IMG_2591-1.jpg


there was only 1/2 a cup of oil left in there. i'm luck i didnt go for any long trips in it.

BUT!!
this concerns me a little, it seems at one time the pinion maybe was rubbing here, but i cant imagine how. the po must have had a pinion bearing go out at one time.
if anyone has seen this before chime in please

IMG_2592-1.jpg
 
I've seen that several times when a pinion bearing fails.
 
i finished up with the frame and underneath stuff today, then went for a RIDE :cheers:

IMG_2597-1.jpg


IMG_2596-1.jpg


IMG_2595-1.jpg


IMG_2594-1.jpg


IMG_2598-1.jpg


well this stage of the build is coming to an end. im just waiting on the body shop for doors tailgate and rockers.

next its just little stuff like:

a 4 switch panel
3 point belts
longer brake hoses
caster shims
putting on my 2100 carb after i rebuild it

this build wasn't about dumping tons of cash at it with the best/coolest stuff. there are alot of builds like that on here and they are beautiful. if i could afford one of those builds i dont think i could enjoy it like this one. they are TOO NICE :drool:

my build was about doing what i could with a small budget that went quickly. i spent a little more than i planed but i did accomplished what i wanted to. a jeep that's trail ready, fun to drive anywhere, preserved/rust free, and looks great to me. this jeep makes me happy.

stay tuned and vote for me for CJ of the month!!!!!!!
 
Great Job!! I love the high end builds but I like the "budget" builds just as much. Just because you don't have all the bells and whistles dosen't mean you can't have a nice quality Scrambler that you built yourself and I think you have proved that!
 
I think it's great! Who cares about the budget, as long as you're happy with it. I just wish mine looked as good as yours.
 
Wow man. Just read this whole thing. Congrats, that's one sweet lookin rig. I'm really diggin the Cuda green. Good job! :cheers:
 


Jeep looks great...
but if youre painting the frame and underside like that, get some jack stands and block the front wheels. NEVER work under or around a vehicle supported by just a jack. not smart. VERY DANGEROUS!!!
 
Out in the light against the trees make it look even greener than when it was in the shop.
 
we had a big snow storm here so no power, heat, etc.
using my generator for the last 3 days, it lots of fun

jeep012-1.jpg


my switches came in and i was ready with a diy switch panel.
i used an old radiator support [ same one thats holding my LF tub section on straight]

jeep014-1.jpg


jeep013-1.jpg


jeep001-1.jpg


jeep002-1.jpg


welded on a lip and drilled a hole to accept the light that was illuminating the oil press. gauge.

jeep003-1.jpg


jeep004-1.jpg


jeep017-1.jpg


here they are mounted up and then with the leds on

jeep020-1.jpg


jeep019-1.jpg


this supplier was great, 4 switches, 2 40 amp relays, and shipping only came to $18 defiantly recommend this company
 
Back
Top