• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Spray Liner - Bulkhead

rreed

Legacy Registered User
City
Anytown
State
TX
I believe this has been asked but I've searched and couldn't find it.

During my restore/build I'm going to have my tub sprayed, tailgate to firewall. I was going to clean/primer the tub area and the bulkhead and have it "sealed" into the tub (install and spray over), permanently leaving the bulkhead as part of the tub.

Now there's a wife and the possibility of youngans one day climbing into the back of dad's old Scrambler from the front so the bulkhead will need to be sprayed separately then installed so I can later remove it. Hopefully one fine day it will get a full soft top (or maybe even hard) so the bulkhead will need to be removed to allow access.

Anyone had any luck spraying their bulkhead separately from the tub and still have it fit okay? How did you seal it from letting in water? Later removing the bulkhead a nightmare? How has it worked out overall? Thoughts, ideas, preferably experience?
 
I would have them spray the Bulkhead and Liner at one time. But they can put in that wire tape and once the spray job is finished pull the wire and separate the bulkhead from the tub.

It will not provide a waterproof seal, but it will match and can be taken out later as needed. You can always run a bead of clear caulking to seal the gap and it will only need to be minimal. Otherwise I think you are going to have a hard time getting the edges of the two pieces to match up if prayed later.

This wire edging should be familiar to them and easy to do.


Carl
 
So when I remove the bulkhead I'd have the "line" of no liner around the bottom of the tub and sides where it was before removing? If I understand correctly?

To clarify, everything would be sprayed at the same time, just not having the bulkhead installed in the tub. If you're thinking I'd have it sprayed at a later time?
 
My Cj8 was sprayed tub and bulkhead all in one piece. It doesn't look very good once the bulkhead is removed. My suggestion would be to spray the tub floor, wheelwells and firewall. If you spray the sides you will need to mask off where the bulkhead fits the sides or you will have problems installing it. You can't spray on the bulkhead where it bolts to the body or you will have fitment issues. I would spray everything else on the bulkhead though. The area on the tub sides where the bulkhead fits I would paint black, or the color of your liner. I would stop the liner on the sides where the bulkhead starts and leave everything forward of that painted black. The liner will act as a seal on the floor when the bulkhead is bolted on. Good luck.
 
I did exactly what you are asking and had no problems fitting or sealing the bulkhead. I painted the inside, bottom, top and sides of the bulkhead then used bedliner on the tub side. I just put a bead of black caulk on the bed side to seal it. I had to use a flexible hose taped to a caulk gun to get the caulk up the sides. You could try fitting first before you do it to see if you will have the clearances you need.
 
Just to mucky your thoughts, I would emplore you to reconsider lining your bulkhead unless it is all hammered up to unsightly condition.

Leaving it body color leaves a very nice color contrast, keeps a rare piece of metal original and it is no more at risk of rust than your fenders.

I suggest rhinoing the tub as planned (everywhere, even under and beside the bulkhead) and leave the bulkhead original paintable metal. It looks best when you look in the cab from the front and it looks good from the rear with the compliment of the roll bar being painted body color as well.

IF you hate the way this looks, you could always rhino the bulkhead later and instead of leaving an uncovered part on the sides of the tub, don't do the sides of the bulkhead.

Another detail is that I never have the Rhino or Linex thickly applied anywhere. IMO, all you need is a good thin coat to take the oxygen away from the metal. The bulkhead will fit tightly after lining if it isn't thickly applied.

Yeah, it's just my opinion. Neither way is life or death but once you rhino that bulkhead it's that way for life and there is no going back!

No matter what you do, get rid of the EVIL gasket that goes on the bottom of the bulkhead that holds water. It actually wraps up the front and back of the BH like a water trough to hold all that watery, salty sandy, gritty goodness?! :( I thought Dennis Collins was crazy when he asked for some original ones from me in his attempt to have it reproduced. I had a small stack of them to give. I guess it's ok for show Jeeps but you won't find one in any of my Scramblers...

Rudy
 
Hmm... Well if this helps, I'm not having it sprayed to protect from or prevent rust (that's just bonus, in theory) but to do its job of being a reasonable protection against scratches/dings and a good tractive surface for anything in laid in it. I do find sprayed tubs cosmetically appealing. And since I'll grow old and die w/ this vehicle I'm not overwhelmingly interested in resale value. To that end, my bulkhead is actually in pretty sad shape.

I don't have the gasket that might have originally been there but have always wondered how it was sealed from the factory. If I end up spraying the bulkhead separately to leave it "removable" my thought was to use some silicone caulking around it to keep water out.

I do very well admire and appreciate your purity in Jeep vehicles, I'm a self-proclaimed purist at hear too. :cheers: Wish we had more people in the world like this.

4miles, am I understanding you sprayed the tub normally, then the front/back of the bulkhead, but left the sides/bottom (contact areas) of the bulkhead un-sprayed then just siliconed around when installed in the vehicle? Or wait, you simply painted the bulkhead but lined (sprayed) the tub?
 
I primed the entire bulkhead and then spray painted all of the bulkhead except the tub side which I did in bed liner after masking off the sides, top and bottom. I used black silicone caulk thinking that would be the easiest to remove if I ever decided to. If I thought there was a chance that I would have to paint over any of it, I probably would have used urethane type caulk but thought that would be harder to remove.
 
Thanks for the kind words! :) I just hate rust and know how hard it is to find good bulkheads and once a bulkhead is lined, there is no going back (within reason).

Just a thought as I have had a lot of these done is that when you tighten the bulkhead down to the tub. the rhino itself acts as a gasket and water intrusions to the cab will be non-existant or minimal as silicone is unsightly and a nuiscance to clean later. Open your drain holes in the floor and let any excess pour out.

I would not line the sides or bottom of the bulkhead and just bolt it in. If you get more water than you want, then silicone it later.

Rudy
 
Just my :twocents:, but BEWARE of spray on liners, especially if you plan on keeping the Scrambler for a long time. I would rather see the rust coming, versus stepping on the bed floor one day and falling through;)

100_4274-1.jpg


100_4273-1.jpg


100_4275-1.jpg
 
So far I'm kind of liking the idea of spraying the tub and bulkhead separately, but taping/not spraying the sides/bottom of the bulkhead for fitment concerns. It's easy to think of spraying thinly in that area but I'm sure when the spray guy has six more trucks lined up waiting to shoot before he gets out at the end of the day, how much is he going to remember/care about special instructions?

I do intend to keep this vehicle into my old age and beyond and since it's a complete frame-off restore I will be as meticulous about the body work and prep as can reasonably be done. My plan and intention is to clean it down as far as possible and a couple good coats of heavy primer to seal the metal. Maybe an extra coat after seeing that! I can't help wonder how well that tub was prepped? I wonder if it was already well on its way to sad shape before it was sprayed? It looks very much like existing rusty scratches/scrapes before and factory paint that was barely holding on. Then got worse later... I agree, once water gets underneath it, it's all over w/. That's why only the inside of the tub will be sprayed and the outside painted--especailly the fender wells. I see numerous religious discussions on whether or not you should ruberize undercoat your fenders, etc. and my thought is it's easier to hit it w/ the 3M wheel and re-rattle can it than to discover bubbles and have to remove that stuff later. Pretty tough argument but we are beginning to digress. :) Worse comes to worst you can always say I told you so!
 
great thread! I was thinking of doing the same thing and this has been VERY helpful. I'm actually thinking of fiberglassing my tub first to cover the small holes and then spray over that. I wasn't even thinking about the bulkhead issue! Thank GOD I read this. It has saved me alot of time and heartache. I will sand the tub first before applying the glass. I'm hoping this will help reinforce the bed so I don't fall through at some time in the furture.
 
Back
Top