• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

The latest prodject

So a lil update(actually from saturday afternoon-sunday morning).

So all was in line to make this thing start and run. I ran the fuel system and made sure there were no leaks. none.

So here came the moment of truth--cranked it over waiting for the loud roar of open exhaust--nothing...

So I quickly checked for spark and injector pulse--neither. So I will say I had a general idea of how this system worked--but not as much as I was about to learn. So I hit up google and did a bunch of reading and the whole cps thing kept popping up.

So I hooked up my meter and low and behold it only had .120 volts a/c and according to what I had read spec is like .5-.8 volts a/c. So here I thought-there is my problem. So I sawpped it out with another one we had. Same problem.

So I dug deeper on my search and found a tsb concurning the distance from the cps to the reluctor on the flywhel and how they had a slotted cps and also info concerning rust on the reluctor. So I made a jumper so I could crank the engine over and polished the reluctor with a wire brush. Ok so I went and slotted the cps little by little with each time getting the voltage to come up to I finally had roughly .6 vokts a/c.

So I hooked everything up thinking I was going to hear that lovely sound. NOPE..

So my next step was to run jumper wires from the cps to the ecm--no change

So at this point I started second guessing my wiring job. So I spent some time checking each and every wire/circuit and testing all sensors except temp sensors(which even if they failed you would not loose injector pulse or spark). I didn't find a single problem.

So I call joe and and let him know whats up and I suspect a failed ecm--now granted I suspected it but I could not belive it. Joe said ok and we could get another ecm--but my gut said no--not yet,lol.

Now at this point I am just dazed since the dist output and cps are within spec. So I went and asked for assistance on my forum (something I hate to do).

So john came thru and stated there there were in-deed 2 flywheels --the renix had MANY notchis in it where the HO had very few and yup--the one we have has very few. So as it turns out we have the wrong flywheel..

Now this is the funny part where under normal circumstances you would have thought it fired due to the output voltage of the cps but in fact it has to do with the actual sign wave---something that could have been seen with an osciliscope.

So john has the correct flywheel and joe is going to grab it so I can yard the trans out and fix it up and we can---hear that lovely noise,lol
 
Ok so joe stopped by the shop on friday for a specail delivery. He dropped off another flywheel and just looking at it--it looked like the one from the description of what should be there.

So I went and ripped the trans/t-cases out of the rig.

Here are both flywheels--you can definately tell they are in-deed different. The one with ALOT of notch's for the reluctor is the right one.

joe147.jpg


So once the whole works was thrown back into the rig--guess what--it bloody started. Joe got an interesting voice mail today
 
So I decided to go ahead and dig into the hole in the floor.

So made a few templates and made a few changes along the way--here is the roughed in tub work.


joe148.jpg



And here it is after alot of smoke(what is with the bottom of jeeps liking to catch of fire,lol) and some lovin.


joe149.jpg
 
So now one thing I knew I would have to deal with was the fact that the seat base would no longer easily just bolt back in. I had talked with joe to see if he could find a non adjustable seat base--and he was unable to easily locate one.

So what I did was put the seat in the forward tilt position--and just welded that sucker up so that--it was no longer a tilt forwrd base,lol...

joe150.jpg


So once that was done I took a few measurements and lopped a portion of the seat off(thats right ---a lil sawzall action)...

joe151.jpg


So once a good portion of the base was removed---did a lil more removal to get it just right and went and made a new portion of the base--and it turned out pretty good.

joe152.jpg


joe153.jpg
 
Last edited:
Ok so since the new portion of the seat base bolts to the new portion of the floor--I figured I would go ahead and add some strength to the floor besides just the sheet metal. So I went and added flatbar to the underside that went from floor support to floor suport and the seatbelt buckle mount also ties into it. I put some god weight on it and the new portion is stronger than the rest of the floor,lol..

joe154.jpg
 
And here is the finished floor...

joe155.jpg


joe156.jpg


And here you can see how the seat fits on the floor--I sat in it and it doens't move so it should "hopefully" be good to go....

joe157.jpg



So once I got the shifters back in here is how it looks for the first time with both seats bolted in for the first time,lol..

joe158.jpg
 
Ok so the next thing I decided to tackle was getting the rear end done or close to it...

So I finished setting the rear housing where I wanted it(was off 1/8"--that kills me,lol) and set the rear u-joint angle. At the same time I figured out where I wanted the track bar mount at. Tacked it all into place and dropped the rear diff out and welded it all up. At the same time I cut them LONG u-bolts down and put the brake hoses on and secured them to the spring plate. So as for the rear end all thats left is the track bar and brake lines(shocks wil be after I am able to drive it and ramp it)

joe159.jpg


joe160.jpg


joe161.jpg


joe162.jpg
 
So today I got a few things done. First was to cut them 10ft long u-bolts down,lol.. I also did the brake hoses the same way I did with the rears and checked them from turning left to right--they worked perfect..

joe164.jpg
 
So since I had a tie rod--oh and I have a ram I figured it was probably time to do something about that little steering issue--since I figured joe might enjoy the rig a little more with steering(well thats just a guess as I think at this point he would be happy sitting behind the wheel making vrrrm vrrrm noise's and yelling at invisable people in his way,lol).

But in any case here is how the ram turned out. Since the axle was stil full width it gave me enough room to run the ram over top of the housing. Needless to say joe should not have any issues with his steering.. One thing I gotta get tommorow are some grade 8 bolts to replace the too short grade 2 bolts that are holding the diff cover on..

joe165.jpg


joe166.jpg


joe167.jpg


The clearance turned out AWSOME and its a very nice tight fit--with no binding of the ram from lock to lock..... So I have my list of needed hydro stuff and tommorow I will hopefully be able to get the rest of the needed items to finish the setup...
 
What kind of paint do you use on the frame??? Looks very nice, similar to what I hope mine looks like in the future...
 
twmattox said:
What kind of paint do you use on the frame??? Looks very nice, similar to what I hope mine looks like in the future...

Hammerite brand--black hammered finish.. I use it alot
 
crash said:
Hammerite brand--black hammered finish.. I use it alot

WOOOOOHOOOOOOO!!!!! I can do something just like Crash!!!

I love that paint, used it on all my front suspension pieces. It attracts mud just as good as the stock stuff ;)
 
bigwalton said:
WOOOOOHOOOOOOO!!!!! I can do something just like Crash!!!

I love that paint, used it on all my front suspension pieces. It attracts mud just as good as the stock stuff ;)

lol...

You should try the bush on version next :D
 
So, I have questions on what you do to your frames before you paint them. It looks like a wire brush on the side/underside. What about the top and body mount areas? Do you just pressure wash and paint, or something more? do you do anything to the inside of the frame rails???

On a side note, how does the Hammerite compare to Farm Implement paint??? I just want to make sure I only do this once...
 
twmattox said:
So, I have questions on what you do to your frames before you paint them. It looks like a wire brush on the side/underside. What about the top and body mount areas? Do you just pressure wash and paint, or something more? do you do anything to the inside of the frame rails???

On a side note, how does the Hammerite compare to Farm Implement paint??? I just want to make sure I only do this once...

I typicaly wire brush the rails and them wipe them down with solvent--your just worried about getting any oils off the surface.

As for farm implament paint--I have never used it so i can say ya or na on that stuff. But if you want the most durable finish then you get the hammerite brush on--put a light coat of that down then use the spray can version--I have found this works extreemly well. Or if you really wanna go nuts---go with por 15
 
Ok so the next thing to do was fix a little problem I happen to notice. One thing about the press on style pulley's---the outer edge of the pully must be flush with the pump main shaft.

joe168.jpg


As you can see its a tad off which could cause the belt to chirp(we had this problem on the chev's in 2000-2004).
 
Then next I got the power steering cooler mounted. It was pretty easy once I got the cooling fan removed.

forum


And here are the lines at the pump and orbital. One thing I have done on a # of rigs is just have an end crimped onto the stock hose. It works perfect and no funky odd stuff needed..

forum


joe171.jpg
 
And here are the lines down at the frame down to the ram

joe172.jpg


joe173.jpg


joe174.jpg


So I bled the system the best as possable without running the engine. Once that was done I fired off the motor and the pump didn't make a peep(or at least that I could tell with no exhaust on the rig). So now all I have to do are make a couple little things for the pins at the ram and the steering is now done. I started doing the brake lines at the front diff so once that is done I can toss the tires back on and drop the front on the ground.
 
Back
Top