• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

The little flatty--for a lil fella

First step drop the pan and main caps----wow

forum


forum


gmb41.jpg


Now this was supposed to be a new motor--that was built a # of years ago---ya talk about screwed. Now there was water in the motor but not to the bearing caps..

So I ended up tearing the whole motor apart--went with a different cam and a new crank kit...

And now its was ready to go back in

gmb42.jpg


gmb43.jpg
 
Now when dale dropped the rig off--there were boxes of brackets--and anybody who has ever dealt with the 3.8's--there bracketry is the oddest. Well some searching on the net and playing king jigsaw puzzel guy(love that) I finally figured it out...

gmb44.jpg


Thats right mr motor----I win--you loose :D
 
Ok--so I got a clutch alignment tool and now the motor is ready to drop in..

forum



And while I was walking around--I tripped and bumped into the rig--and dang the fenders fell the heck off :haha:

gmb46.jpg


Oh and then one of the little people from under the stairs snuck out and threw the grill on :redneck:
 
So--here is where I ran into another problem. I never noticed it because I assumed all was good there. Now the plan was to toss the motor in temp to get the clutch fork figured out--but when I started looking at it before I threw the motor in--I found this...

forum


forum


On the housing thats around the input shaft to the tranny the throw out bearing is supposed to ride somwhat snug--well you can see there is 1/8" gap--ya the throw out bearing just flops around on the housing. Well that was only half of the problem. When the whole works is pushed back into place--the lip on the throwout bearing makes contact with the clutch fork.

gmb49.jpg


And what happenes is the clutch fork is not able to rotate (when you push on the fork its supposed to push on the throw out bearing hence pushing on the pressure plate. I am just glad I looked it over before I threw the motor in...

So now the question lies is just the throw out bearing wrong?
 
So at this point I have contacted Novak (last week) and trying to figure out what its going to take to get this thing back in.

So in the mean time I decided to carry on with other items..
 
So since I had space to work without the motor in the way--I went and ripped all the stock pedal stuff out---wow they made these pedals to withstand a large calibur round I think :eeek:

gmb50.jpg
 
So time to have a lil fun on thne tub.

Here are the seat mounts that were in the rig.

forum


Here is the roll bar-thing a ma gig--cute isn't it :redneck:

forum


Here is the steel plates on top of both fender wells--yes thats 1/4" plate with 1/4" angle material...

forum


Here is the fuel cell that was in the rig---and there is a piece of wood thats there as an insulator :eeek:

gmb54.jpg
 
I found a little trick--how to lighten a rig up by a couple hundred pounds--and yes that is poop pipe :haha:

forum


Ahhhhh---that looks a lil better---reminds me of an episode of mash :haha:

forum


So once I unbolted--then cut the old stuff out---had to do a lil grinding ---here is what I found under the plating on the fender wells..

forum


forum


gmb59.jpg
 
So I am still kinda poking along. I got to looking over the rig more--and decided to pull every strand of wire out of the thing--most of the wires were cut anyways and well--it was a HUGE mess(also pulled the fuel and brake lines--well what there was)..

gmb60.jpg
 
So since we are going to run fenderless--these lil things are are worthless

gmb61.jpg


The body cross supports are all rusted away and I thought they were bolted on--but nope--So with a lil effort--the did fall off..

gmb62.jpg


I still have a lil cleanup work where whats left of the body supports are...
 
Here is the pedal assy we got from an old jeepin buddy .. As a whole its very nice but I will have to rework it a bit to get outa it what we need..

gmb63.jpg
 
So I looked and measure the pedal assy and the firewall where its going to sit against--and was origionally going to way till I got the steering column it--but with how the firewall is---there is only one place its going to sit--so the clearance to the steering column will have to be corrected by reworking the arms on the pedals--which isn't a big deal since I was going to rework them anyways..

So with how the firewall is--its going to have to be plated for support of the pedal assy and help with the flex on the firewall..

I just haven't figured out if I am going to use 1/8" or 3/16" plate. I also plan on running some tabs off the plate to wrap around the firewall a bit to help support it.

gmb64.jpg



And here it is all prepped--I even got a template cut out for the plate

gmb65.jpg
 
So I got a lil busy again today. So I decided to go ahead and use 1/8" for the support plate--3/16" just seemed too thick.

So got out the plasma and cut it out to the template. Once it was cut and fitted I went and indexed the plate to the pedal assy at the firewall and drilled the holes in both the plate and firewall.

gmb66.jpg


Once that was done I went and stripped the pedals off the pedal assy and trimmed 1" off the front side of the pedal assy and cleaned some of the rust off it.

gmb67.jpg
 
At this point I went and painted the bare metal areas for some protection and bolted it in place with the pedal assy.

gmb68.jpg


Once bolted I went and welded the top edge and around about 2/3 on the drivers side to really tie the plate into the pinch welds of the firewall.

At the bottom I went and added a couple tabs. The support brace that goes from the frame up the botom of the rig was broken at the top, so I welded it to the plate and added a gusset to help give it some strength.

gmb69.jpg


And here is how the pedal assy looks under the dash--its a tight fit but fits nicely. I also pulled on it as hard as I could and it doesn't move one bit--I like it

gmb70.jpg


gmb71.jpg
 
Ok so I have been literally workin myself to death out in the yard--so I am now caught up for the time beaing(only a couple items left :awesomework: )

Ok so this lil gem was dropped off last week..

gmb72.jpg


Its out of a YJ--just what I was looking for. So I took some measurements..

Here is the adapter (at least for easy terms I will call it that)

gmb73.jpg


So I basically cut it and reworked the firewall side of it, drilled it and cut a hole in the firewall

gmb74.jpg


gmb75.jpg


Once that piece was made--I went and measured/trimmed the tunnel portion of the adapter (roughly shortened it by 1.5")

gmb76.jpg


And there is the booster on the firewall..

gmb77.jpg
 
So now its time for a lil fun--this was as of last week

Front hoop..

gmb78.jpg


This poor thing is just so bent/twisted.
 
One thing dale decided he wanted--the stock fenders tossed--so I said---ok

I tried like heck to keep the origional lines/look of the MB on the nose. It ended up being some tough bends, a couple of the down portions of the bends ended up not being square with each side due to the tub--but you wouldn't know it unless you cross measured.

So in any case I figured where the main support bar was going to land on the frame--had to lop off the lil tabs that go from the tub to the frame(will have to replace them--no biggy) and went and plated the frame on both sides

gmb79.jpg


And here is where the tube nails it..

gmb80.jpg


I am also going to use this spot for the A pillar when it comes time to do the cage since the body supports on the tub for the front of the tub are pretty bad..

So when I ran the main support bar--it hugs the fron of the tub---landing right at the outer edge. At the same time I made tabs to help support that are of the tub..

gmb81.jpg


And here are how the fenders turned out

gmb82.jpg


gmb83.jpg


The main support bars turned out perfect as the nose fits down snug between them--will make mounting/supporting it really nice. Plus I will run a bar under the hood behind the nose to help hold the rad when that time comes.

Also there are no supports for the fenders yet--will run another cross bar once the motor is back in and room is figured out...
 
Lookin' good, Crash! Love those fenders!
 
Back
Top