• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Tip of the day

scott anderson

Old age Mutant Ninjaneer
City
Paragould
State
ar
I thought we needed a thread on the great tips that we have learned over the years. I have been reading a lot of posts of several boards about pilot bushing removal. So here is tip #1


To remove a stuck pilot bushing; 1st drill out the bushing with 9/16 drill. Then tap the hole with 5/8-12 threads. insert a 5/8 bolt and screw it into the hole till it bottoms on the crank. If it does not come out easy, tighten it tight then hit with BFH, then tighten again and repeat till the bushing turns right out. I have used this method many times and it works. If the bushing is alread worn past 9/16; drill it with an 11/16 drill and tap to 3/4 and use the same process.
 
scott anderson said:
hmmmmm...maybe this was not as good an idea as i though:cool: :rolleyes:
Foolish me....I thought you were going to be posting each "tip of the day". Now I understand, you want the rest of us to contribute.....:rolleyes:
 
John N said:
Foolish me....I thought you were going to be posting each "tip of the day". Now I understand, you want the rest of us to contribute.....:rolleyes:

yep..that was the idea...tip #2 if you want to build a level pyramid..flood giza then level off the waters' surface
 
Last edited:
Pack the bushing with wet paper then use an old input shaft and hammer it in there. By doing this multiple times, you can hydraulic the bushing out of there...
 
This also works if you pack the void with axle grease, then pound in the unthreaded shank of a suitably-sized bolt. Takes a little while, as most of the grease will try to come shooting out between the bolt and the bushing, but it works.
 
i have used the hydraulic technique and it works great most of the time...my method is more for when it is really stuck or is worn oval and does not seal well enough for the hydraulic method
 
Tip

Here's one for you fellas. If you've been wrenching and get really nasty and take a bath or a shower and don't want to leave a ring around the tub. The best thing to get rid of it is fast orange by gojo. This works better on the ol ring around the tub than any bathroom cleaner. This has gotten me out of trouble with the wife more than once.
 
Use the hydraulic method and wrap masking tape around the bolt or dowel until you get a really close fit. The closer the better.
 
Instead of penetrating oil/liquid wrench/etc for removing rusted bolts, heat with a plumber's soldering torch using propane (blue bottle) or MAPP (yellow bottle) and then twist/remove while still hot/glowing. Reheat as necessary.

(Heating best done on rusted fasteners that are not near fuel lines, fuel tanks, plastic or your fingers:D ).
 
Great thread idea.

Here's one of the best tricks that I've learned from this board thanks to Big Mark: how to remove u-joints no matter how stuck they are.

I've used this more than a dozen times now on all conditions of u-joints (some insanely nasty rusty ones) and without fail they pop out with just a couple pops of the BFH.

linky
 
If I'm going to get greasy, or even just dirty, I often rub my hands down with Dawn detergent BEFORE I go out to work, and I don't rinse them off. Just put the detergent on my dry hands, rub it in until it's pretty much gone, and go work. When I come back in, I just wash my hands as normal, and I don't have any of the skin staining or hard-to-remove dirt and grease like I would if I didn't coat the skin with the detergent first.
To those who ask why I don't wear mechanic's gloves, I have to say, fingertips. :D Can't manipulate the part if you can't FEEL the part! Seriously, I do wear gloves if I'm going to be working with big stuff, but for fiddly little things like carburetors, electrical connectors, etc, I just soap up n go.
 
On the gloves, I got a nice pair of mechanics gloves, and felt much the same way about the feel.

A friend turned me onto the cheap rubber-dipped cloth ones at the AutoZoo or Advance (I forget which) and they're MUCH better for dirty Jeep junk. His whole body shop uses them.

The ones I have are well textured on the rubber and the rubber is just thick enough and wraps around your fingertips. I purposely got a size too small and they are nice and tight and do great helping with that "fingertip feel".

One other cool thing is that, because they're rubber and pertty chemical resistant, I just hit them with Gojo when I'm done and clean them as I'd clean my bare hands and they stay nice for a long time. I've used them for about a year and have only gone through one pair with pretty heavy use back when I was finishing my build.

I save the mechanic's gloves for things where I worry about cutting or punctures, but that's about all I use them for anymore.
 
Surgical Gloves

I have been using surgical gloves when I have to do something dirty in the garage. Usually, I'll put them on under a set of regular gloves and when it comes time that I need that fine touch, I'll take the other gloves off and these will be ready. They are great and then you just toss them in the garbage. They are cheap too.

Only problem is that they will fall apart when you get gasoline or parts cleaner on them.
 
Keep an eye out for nitrile surgical gloves. I work in the environmental field and have nearly an endless supply of these. They are very chemical resistant and go on just like latex gloves. I do what you described too...nitrile gloves on under my mechanix gloves.
 
twmattox said:
Keep an eye out for nitrile surgical gloves. I work in the environmental field and have nearly an endless supply of these. They are very chemical resistant and go on just like latex gloves. I do what you described too...nitrile gloves on under my mechanix gloves.

and i thought i was the only one doing this lol......guys at work rag on me about this but it keeps the hand soft and clean like a real mans ...
 
my wife can get those by the bushel and I tried them, but they made my hands sweat so much I couldn't stand them.
 
jmarkel said:
Only problem is that they will fall apart when you get gasoline or parts cleaner on them.


Were they latex? There are some just like them that are vinyl that hold up better to chemicals. I used them recently with paint stripper and paint thinner and they held up well. The latex ones fell apart.

I got them at a local hardware store. They were in the paint section.
 
Here's a tip for you.
Getting rid of the ole yJ etc. air fliter intake box, don't, use it for a tool box & re-route your supply hose to the carb by-passing the box. After the filter is installed of course.
 
Back
Top