• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Transmission Question for 5.3 swap

Husker fan

Legacy Registered User
City
Caro
State
MI
I am currently in the middle of getting parts to do a 5.3 swap. So far I have picked up a 2009 5.3 out of a Tahoe. I plan on going with a manual transmission. I would like a manual with over drive. From what I have read the ax15 is a possible option. The other option I am looking at is a nv4500. I only plan to do mild off roading nothing to crazy. I only want to do this once but don't want to go crazy over building. Does anyone have experience using either one of these transmissions with a 5.3? The Novak website says the ax15 is strong enough to use with the swap but would prefer some first hand experience. Thank you
 
NV4500 would be a one and done, never have to worry about it ever. You might be able to find a NV3500 out of a Chevy Pick Up, that could work.

The AX15 is a decent one but you would be looking at both engine and transfer case adapters. Call and talk with Novak. They probably have some good recommendations on which would be the most economical way to go if you are planning on keeping the Dana 300.


Carl
 
I run the NV4500 behind my 5.3l.
The way i see it, build it right or build it twice!



 
I appreciate the input. I was recently reading about a heavy duty ax15 called the terminator transmission. The info I have found is that people are talking about it being around $1700. Might as well go with nv4500 for that price. Bad Karma did you have to use a 1 inch body lift for the transmission to fit?
 
Novak, Advanced Adapters and Bud's Unlimited are all great sources for anything related to a 5.3 swap. I did the 5.3/4l60/241C swap and used parts and advise from all three. Another company for some conversion parts is JB conversions if I remember correct. I didn't use any body lift but did use a 2 1/2 inch suspension lift.
 
I appreciate the input. I was recently reading about a heavy duty ax15 called the terminator transmission. The info I have found is that people are talking about it being around $1700. Might as well go with nv4500 for that price. Bad Karma did you have to use a 1 inch body lift for the transmission to fit?

Initially I had planned on a NV3550 behind the 5.3 in my Scrambler. After many conversations with Eric at Novak, I was sure that the NV3550 was a great choice. Then I went automatic...

The primary reasons I chose the NV3550 over the NV4500 were size and shifting. The 4500 is a monster, and feels more truck-like. The 3550 is a lighter weight/duty transmission, and with a short throw shifter it almost feels like a sports car transmission. They do make a short throw shifter for the 4500, but the ratio spread is still more truck-like. I have a 241OR transfer case so I didn't feel the need for a super low 1st gear.
 
If you're running 2.7 gears then OD is not needed...unless running 235/75/15 tires......but its up to you.
a native chevy manual tranny (4sp with granny gear) installed in this application, with 33in tires will cruise at 80mph@2200 rpms aprox...I would swap the tcase for a chevy native and done!!!...no adapters required...

if you think a manual with OD is in your future I would hunt for an early 90s dodge 3/4 pick up equipped with a nv4500.
this nv tranny shares the bellhousing bolt pattern with 96+ chevy ones ..only need to swap the input shaft for a stock chevy one (an $80 part ) and a lathe to modify the retainer....no-where near the cost of adapters....clutch and all other components are chevy stock..nothing fancy here...

the tail (being dodge) means its compatible with the d300 pattern, no adapters required, and 19 spline??not sure the number but I'm sure is the same spline count the d300 requires in stock presentation.
one downside for this tranny , it will require the use of a custom crossmember/support hanging way below the frame rails....you would be draggin' all over the places when offroading... ......aftermarket tailcone/tcase adapters are available to correct this non desirable condition...(a $350 component)... assuming you buy the tail adapter you would be saving "mucho" $$ compared to the cost of adapters.

my 0.02 MX peso comment
 
Randyzzz. What were you told about the strength of the nv3550? From what I have read is that the ax 15 and nv3550 are equal in strength. The size of the nv4500 and gear range have been the two things making me reluctant to go with the nv4500. I appreciate all the input everyone has given.
 
Just my 2 cents worth. Novak probably has as more experience than 98% of the members here but the more informed you are the better your decision will be.
 
The NV3550 and the AX15 are similar in strength, with possibly a slight edge to the 3550. The 3550 has been OE in certain designs behind V8's.

I really didn't want a huge low hanging Trans like the 4500.
 
When I was putting my scrambler together the first time. I started to fit up a NV3550 behind my 5.7. The hump on the bellhousing for the hydraulic clutch was in the way for the front driveshaft. It had a 2 1/2" lift and I was planning on a Dana 300.

Just something to check when considering. I think some of the NV3550's had internal slave cylinders that would change the bellhousing shape.
 
The AX15's and NV3550 are pretty stout behind 4.2/4.0's, I don't know if I would want one behind 300 HP :shrug::twocents:
 
The AX15 in stock form is rated for 300ft pounds of input torque and I have read that is a conservative estimate. Novak has then for sale that they beef up to handle more power so I think their units would be fine behind a 5.3,
 
The AX15 in stock form is rated for 300ft pounds of input torque and I have read that is a conservative estimate. Novak has then for sale that they beef up to handle more power so I think their units would be fine behind a 5.3,

I bought a new Novak AX15, it is behind my 258 with MPI in my red Scrambler. It "might" hold up behind 300HP, but I wouldn't trust it as much as an NV4500 in this type of application :twocents:

Then again, I break transmissions on a regular basis :shrug:

(x4) T-150's (x3 behind a 258, x1 behind 304)
(1) T-18 (behind 304)
(x4) T-5's (behind 258)
(x1) 700R4 (behind 350, but it was probably broke before I fried it)

AX15 might be fine, but I wouldn't necessarily be 100% confident in it, if that makes sense :twocents::cheers:
 
I bought a new Novak AX15, it is behind my 258 with MPI in my red Scrambler. It "might" hold up behind 300HP, but I wouldn't trust it as much as an NV4500 in this type of application :twocents:

Then again, I break transmissions on a regular basis :shrug:

(x4) T-150's (x3 behind a 258, x1 behind 304)
(1) T-18 (behind 304)
(x4) T-5's (behind 258)
(x1) 700R4 (behind 350, but it was probably broke before I fried it)

AX15 might be fine, but I wouldn't necessarily be 100% confident in it, if that makes sense :twocents::cheers:

Thanks for the warning.
YOU ARE NOT ALLOWED TO DRIVE MY JEEP.........EVER.
 
Thanks for the warning.
YOU ARE NOT ALLOWED TO DRIVE MY JEEP.........EVER.

No problem :thumbsup:

It's not that I am really abusive, just certain transmissions suck: while others, eventually anything wears out with miles :twocents:

T150's seem "marginal" behind a 258, won't last with a V8 :twocents:
T5's are OK behind a stock 258/on a stock Jeep, won't last with a V8/hopped up 6/33" tires/off-road use :twocents:
My 700R4 was wasted before I ever really drove it, so :shrug:
My T18 was good for around 150k miles, then it had to be completely rebuilt, bearings and syncro's, but some gears were damaged, too :shrug:

I had the most luck with my now sold 05 Rubicon's NSG-370 6 speed - over 165,000 miles on it when I sold it, only one fluid change, never had any trouble out of it. That Jeep, I bought brand new, I took care of it. When I sold it, it still had factory u-joints, clutch, rotors, belts and hoses on it. I only ever changed out the following: battery, brake pads once, starter at 155,000 miles, front axle inner seals at around 125,000 miles, and the stupid OPDM thing.

If you take care of stuff it will last:twocents:

I just feel hesitant to recommend a "medium duty" transmission somewhere where a HD would be better suited :twocents:


Even the almighty NV4500 will wear out, we just had one go out on a work truck, Dodge Diesel, but it lasted 250,000 miles, so it lived a full life :shrug:
 
I'm researching this same topic. Currently have a stock T5 behind a SBC 350. It is not a high horsepower motor but more then a 258. I really thought I wanted to go with an NV4500 but I'm really considering a NV3550. Main reason is the 3550 is smaller and would have less fitment/fabrication issues. My build is already WAY behind and I want to get it finished THIS year. I will be sticking with the D300 x-fer case. However, I also don't want to revisit this issue later if the 3550 isn't going to hold up.
 
I have burnt one engine and two transmissions in my entire 49 years of driving and all three were my fault and when I was a teenager. I change engine oil every 5k and automatic trans fluid every 25-30k religiously. I check fluids in everything every 6 months. I own way to much **** to be having unnecessary break downs. Heck I check tire pressure more than most people check oil level.
 
Back
Top