• Notice for iPhone users: DO NOT use the image size reduction option when uploading photos to the forum. This causes portrait images to post as landscape. We have added a warning to the image insert pop-up as well.

Transmission Question for 5.3 swap

Has the 5th gear nut backed off? That is usually a problem with high vibration diesel trucks, not gas engines though.
I highly doubt it, it was peined onto the shaft and I have only driven a few thousand miles.
 
I would suggest removing the shift tower and looking inside the transmission. Or at the least the PTO plates on each side. Something does not sound right inside it.
 
I would suggest removing the shift tower and looking inside the transmission. Or at the least the PTO plates on each side. Something does not sound right inside it.
I have removed the shift tower and even tried a new one from advanced adapters. Same issues.
 
I run the OEM GM NV4500 oil. I've heard NV4500s are super picky with oil.

below are my clutch parts that I run. I put the cheap crap in because I wasnt sure what would work and I didnt want to waste money on the expensive stuff. 11-12 years later its all still working great.

Throwout Bearing - 1962 Chevy Belair 3.8L inline 6 - National P/N 1697C
Flywheel - SACHs p/n NFW1050
Clutch kit p/n 04-232
pilote bearing - GM p/n 12557583

dunno if any of that helps but..
 
I run the OEM GM NV4500 oil. I've heard NV4500s are super picky with oil.

below are my clutch parts that I run. I put the cheap crap in because I wasnt sure what would work and I didnt want to waste money on the expensive stuff. 11-12 years later its all still working great.

Throwout Bearing - 1962 Chevy Belair 3.8L inline 6 - National P/N 1697C
Flywheel - SACHs p/n NFW1050
Clutch kit p/n 04-232
pilote bearing - GM p/n 12557583

dunno if any of that helps but..
That does help, what is the part number of the oil you are running? I talked to my local Chevrolet dealer and they said it is discontinued.
 
not sure, I filled it in 2012 :ROFLMAO: but it did have GM all over the bottle.

I'll check when I get home... I may have a bottle somewhere
 
Haha no worries. From the forums I have read it looks like the redline mt-85 is the closest replacement for the gm and mopar oil. It is a tad thinner which is why I switched to the thicker amsoil gl4 oil. Unfortunately no change. I am thinking it has to be a clutch issue.
 
dunno if some said it already but check and make sure your throw out bearing isn't in contact with the fingers of the clutch when the pedal is fully disengaged.
I went through a ton of different throw out bearings before finding the one that didn't touch.
Come to think of it, I've heard that the counterweights on the center force clutches can cause problems too, but i've never has experience with them. Another reason why I went cheap on the clutch... rockauto special
 
dunno if some said it already but check and make sure your throw out bearing isn't in contact with the fingers of the clutch when the pedal is fully disengaged.
I went through a ton of different throw out bearings before finding the one that didn't touch.
Come to think of it, I've heard that the counterweights on the center force clutches can cause problems too, but i've never has experience with them. Another reason why I went cheap on the clutch... rockauto special
I will crawl under there and take a look. Not sure if I will be able to see through the bell housing
 
pop the rubber boot off the clutch fork... or are you running an internal slave?
 
I am running an internal slave yes. I have also thought maybe a shim between the internal slave and the bearing retainer. But sounds like you need space there. Best option could be to convert to an external slave maybe?
 
you'd have to take it all apart and measure everything. fun with the very light weight NV4500...
 
I am wondering what the width of your bellhousing is. I am running a bellhousing off of a 454 Chevy. Curious if maybe it is too short?
 
Im pretty sure Im running a factory bellhousing for when the GM trucks actually had an LS and NV4500 from the factory. I think they were made for 3 or 4 days, there wasnt many.
 
Im pretty sure Im running a factory bellhousing for when the GM trucks actually had an LS and NV4500 from the factory. I think they were made for 3 or 4 days, there wasnt many.
This is what I have. An NV-4500 that was behind an LS 6.0. 2003 I believe.

Is there a difference in the syncros for the Chevy vs dodge? Dodge ran the 4500 until they went to the 5600 6 speed.

Found this on the interweb, not sure how accurate it is:

These are the ONLY lubricants recommended for the NV4500:
75W-90 Castrol Syntorque Synthetic
Mopar Manual Transmission Lubricant (PN 4637579)
GM Transmission oil (PN 12346191)
NOTE: Syntorque is NOT the same as Castrol Syntech.

Reason for special fluid, Synchronizers: Carbon fiber composite
 
Those of you with NV4500s, what are you using for the transmission crossmember and mount?
 
Back
Top